Simrad LiveSight Thru-Hull Manual

Simrad Skibsradar LiveSight Thru-Hull

Læs gratis den danske manual til Simrad LiveSight Thru-Hull (2 sider) i kategorien Skibsradar. Denne vejledning er vurderet som hjælpsom af 5 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 3 anmeldelser. Har du et spørgsmål om Simrad LiveSight Thru-Hull, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Dimensions

Parts included

A M8-1.25, ange nut, 316 ss (x2)

B M8 washer, 316 stainless steel (x2)

C M8 washer, nylon, M8, 8.5mm ID, 16mm OD (x2)

D Flange nut, M33

E M33 washer, 316 stainless steel

F M33 fairing isolator washer, nylon

G M8-1.25 x 185 mm stud, 316 ss

H M8-1.25 x 150 mm, stud, 316 ss

I Isolator sleeve, M8 (x2)

J Isolator sleeve, M33

K Fairing block

L LiveSight thru-hull transducer

M Documentation pack

A Drill

B Drill bits 9 mm (3/8”)

C Hole saw 35 mm (1 3/8”)

D Heat gun

E Sandpaper

LiveSight thru-hull transducer

Installation Guide

Technical specications

Environmental

Water temperature for

operation

0°C to +35°C

(32°F to +95°F)

Storage temperature -30°C to +70°C

(-22°F to +158°F)

Physical

Weight 2.3 kg (Thru hull without

fairing block)

0.84 kg (fairing block)

Cable length 7,6 m (25 ft)

Hull requirements

Dead rise angle 0 - 25°

Max hull thickness 5 cm (2”)

The most up-to-date specications are available at the

product web site.

*988-12344-001*

Compliance statements

Europe

Navico declares under our sole responsibility that the product

conforms with the requirements of:

• CE under EMC Directive 2014/30/EU

United States of America

¼Note: The user is cautioned that any changes or

modications not expressly approved by the party

responsible for compliance could void the user’s authority to

operate the equipment.

Australia and New Zealand

Navico declares under our sole responsibility that the product

conforms with the requirements of:

• level 2 devices of the Radiocommunications

(Electromagnetic Compatibility) standard 2017

Declarations

The relevant Declaration of Conformity is available on the

following websites:

• www.lowrance.com

• www.simrad-yachting.com

Address

Navico Logistics Europe B.V.

Laan van Europa 450

3317 DB Dordrecht

The Netherlands

Required tools

195 mm

7.7 “

112 mm

4.4 “

370 mm

14.6 “

132 mm

5.2 “

The Fairing block

A Vessels with a dead rise angle > 10°

B Vessels with dead rise angle < 10°

C Minimum fairing thickness = 12 mm (0.5“)

The transducer must be mounted as parallel to the water

surface as possible.

For hulls with a dead rise angle, the fairing block should be

used to compensate for the dead rise angle.

A B

F Marine grade above

or below waterline

sealant

G 13 mm and 50 mm size

wrench

H Band saw or table saw

Cutting the fairing block

Installation

Mounting location (guidelines only)

L/3

150 - 300 mm

(6 - 12”)

300 - 600 mm

(12 - 24”)

Displacement hull powerboat

The transducer will not work while it is out of the water, ensure that it is in contact with the water at all speeds. The transducer

must be mounted in an area that provides smooth non-turbulent water ow, unobstructed by keel or propeller shafts. On single-

drive vessels, if the propeller is turning clockwise, mount the transducer on the starboard side. If the propeller is turning counter-

clockwise mount the transducer on the port side. On twin-drive vessels, mount the transducer between the drives.

Stepped hull

Mount just in front of the rst step and and between the

centerline and the rst set of lifting strakes.

Planing hull, outboard and stern-drive

Mount well aft, and between the centerline and the rst

set of lifting strakes.

Planing hull, inboard

Mount well ahead of the propeller(s) and shaft(s), and

between the centerline and the rst set of lifting strakes.

Full keel sailboat

Mount in front of the keel at the point of minimum

deadrise angle and close to the centerline.

Fin keel sailboat

Mount to the side of the centerline and 300 – 600 mm

(12 - 24”) in front of the keel.

Attach the fairing block to a piece of wood

using wood screws (not included).

Measure the deadrise angle ( ) at the transducer A

mounting location and adjust your saw accordingly.

Cut the fairing block.3

Mark the holes on the outside of the hull using the

mounting template.

Drill the holes.2

Screw the M8 studs into the transducer.

Metal hulls only, install the isolator sleeves over the studs.

Metal hulls only, make sure that the isolatorsleeves will

cover the contact area between the hull and the studs. Use a

heatgun to shrink the isolator sleevs in place.

Use sand paper to remove all burrs and sharp edges to

smooth the installation surface.

Apply marine grade sealant or epoxy to the sanded surfaces

and to the mating edges of the fairing block. Push the

transducer through the lower part of the fairing block, and

press the assembly through the holes in the boat.

Apply marine grade sealant or epoxy to the sanded surfaces

and to the mating edges of the fairing block. Install the

upper part of the fairing block from the inside of the boat.

Apply marine grade sealant or epoxy in and round the holes

of the fairing block. Secure the assembly with the washers

and the nuts.

Produkt Specifikationer

Mærke:	Simrad
Kategori:	Skibsradar
Model:	LiveSight Thru-Hull

Har du brug for hjælp?

Hvis du har brug for hjælp til Simrad LiveSight Thru-Hull stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Skibsradar Simrad Manualer

Simrad LiveSight Thru-Hull Manual

21 August 2025

Simrad StructureScan 3D Module Manual

21 August 2025

8 Oktober 2024

8 Oktober 2024

3 Oktober 2024

4 September 2024

8 August 2024

6 August 2024

3 August 2024

Simrad IS20 Analog Manual

8 Marts 2024

Skibsradar Manualer

Nyeste Skibsradar Manualer

Furuno MODEL 1815 Manual

23 Juli 2025

Furuno DRS12A X-Class Manual

23 Juli 2025

Furuno FAR-2268DS Manual

23 Juli 2025

Furuno DRS25A-NXT Manual

22 Juli 2025

Furuno DRS4D-NXT Manual

22 Juli 2025

Furuno FAR-2258 Manual

22 Juli 2025

Furuno FAR-1513 Manual

22 Juli 2025

Furuno DRS12A-NXT Manual

22 Juli 2025

Furuno FAR-1416 Manual

22 Juli 2025

Furuno WV-100 Manual

22 Juli 2025