SKS 11322 Manual

SKS Cykeltilbehør 11322

Læs gratis den danske manual til SKS 11322 (1 sider) i kategorien Cykeltilbehør. Denne vejledning er vurderet som hjælpsom af 8 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 4.5 anmeldelser. Har du et spørgsmål om SKS 11322, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/1

MADE IN GERMANY SKS-GERMANY.COM

G E R M A N Y

MOUNTING INSTRUCTION RACEBLADE PRO XL ¬ 11321 + 11322

EN. INSTRUCTIONS FOR USE

The SKS RACEBLADE PRO is an ultra-light wheel protection set boasting excellent splash protection, especially for racing wheels and crossbike wheels. The Raceblade can be assembled in a very short space of time thanks to the simple

SKS quick assembly system. The RACEBLADE PRO is available in two different widths:

RACEBLADE PRO: For racing wheels with a max. tyre width of up to 25 mm

RACEBLADE PRO XL: For racing wheels and crossbike wheels with a tyre width of between 25-32 mm

Rear assembly:

Align the wheel protector facing upwards in such a manner that the distance to the tyre on the front strut (A) is a minimum of 1.5 cm whilst the strut is in contact with the fastening points on the frame. In order to determine the

correct distance, move the strut holder upwards or downwards on the frame. (Arrow C) The distance between the wheel protector and the tyre should now also amount to 1.5 cm on the strut ( ). If the distance is higher or lower, the B

strut must be adjusted to its frame shape.

In order to do so, ﬁrst attach the strut to the seating struts of its frame on each side with the of clamping rubber by hooking the clamping rubber into the fastening points. Clamp the rubber so tightly that it is impossible for

the strut to slip on the frame.

If necessary, use the enclosed paintwork protection in order to protect the frame. Please see the section entitled »Permanent attachment of the wheel protector« for information regarding the permanent attachment of the wheel

protectors with the enclosed cable ties.

The distance between the strut ( ) and the tyre can be adjusted by changing the inclination of the struts (B D). Loosen the four Allen screws belonging to the connection and move the strut into the correct position. Check the distance

between the wheel protector and the tyre once again.

Finally, check whether the distance between the wheel protection proﬁle and the brake is set correctly. It should amount to at least 1 cm. If necessary, set the distance by moving the proﬁle in the strut brackets.

Where necessary, carefully shorten the clamping rubbers with scissors so that the ends cannot come into contact with the wheel spokes.

Front assembly:

As was the case with the rear wheel, ﬁrst check whether the struts need to be adjusted to match the shape of the forks. Pay attention to an equal distance of at least 1.5 cm between the wheel protector and the tyre along the entire

length of the proﬁle. Where necessary, adjust the inclination of the struts as described under Point 2.

If necessary, use the enclosed paintwork protection in order to protect the forks.

Distance between the proﬁle and the forks

The distance to the forks should amount to a minimum of 1 cm. The distance to the forks can be regulated by moving the proﬁle in the strut brackets. Ensure that the distance to the wheel protector is sufﬁcient when the

pedal is in the front position.

You can also carefully shorten the clamping rubber here using scissors where necessary.

Permanent attachment of the wheel protectors

In order to fasten with the quick-release clamping rubbers, the RACEBLADE PRO wheel protectors can also be attached with the enclosed cable ties. This type of fastening is only suitable for the permanent fastening of the RACEBLA -

DE on the wheel. In order to assemble, use a further 2 cable ties per side in addition to the clamping rubbers. Ensure that the cable ties run precisely in the grooves provided for this purpose. Pull the cable ties as tight as possible so that

slipping cannot occur. Carefully cut the protruding ends of the cable ties using scissors.

Safety information!

Before each journey, check that the wheel protectors are sitting correctly. If the minimum distance between the wheel protector and the tyre is not observed, the wheel protector may become damaged and, in the worst case scenario,

could lead to a crash. Therefore, it is essential that the minimum distance of 1.5 cm is observed during assembly. Ensure that the ﬂawless function of the brakes is guaranteed and that the wheel protector does not come into contact with

the moving brake parts. Due to the effect of UV radiation, the clamping rubbers are subject to natural ageing. Regularly check the condition of the clamping rubbers and promptly replace them in the event of damage.

Pro tip

If the wheel protectors are correctly set, the proﬁles can be permanently screwed together with the strut brackets. In order to do so, remove the fully adjusted wheel protectors from your wheel once again.

In order to make this process easier, we recommend pre-drilling a 2 mm hole in the respective position.

Now screw the enclosed screws through the proﬁle and into the drill hole of the strut bracket.

WARNING! SKS is not responsible for damage to frame paint or carbon resulting from use of this product. Proper use of protection ﬁlm and maintenance, including regular cleaning of frame and fender at

attachment points, will prevent such damage.

1,5cm

1,5cm A

1,5cm

1b.1. 4.

1a.

3a.

5a.

4a.

SW 2,5

INBUS INBUS

6b.

6a.

ø 2 mm

1cm

HINTEN/REAR VORNE (NORMALE GABEL)/FRONT (REGULAR FORK)

Lackschutzfolie/

paintworkprotection Lackschutzfolie/

paintworkprotection

ROADALLROAD MOUNTAIN

MONTAGEVIDEO

MOUNTING VIDEO

Produkt Specifikationer

Mærke:	SKS
Kategori:	Cykeltilbehør
Model:	11322
Type:	Fender, Front & rear mudguards (set)
Antal pr. pakke:	2 stk
Produktfarve:	Sort
Produkttype:	For- & bagskærme (sæt)
Antal:	2
Kompatibel hjulstørrelse (maks):	28 "
Kompatibel dækbredde:	32, 25 mm
Forskærm længde:	565 mm
Bagskærm længde:	730 mm