SKS Speedrocker XL SET Manual

SKS Ikke kategoriseret Speedrocker XL SET

Læs gratis den danske manual til SKS Speedrocker XL SET (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 18 personer og har en gennemsnitlig bedømmelse på 4.2 stjerner ud af 9.5 anmeldelser. Har du et spørgsmål om SKS Speedrocker XL SET, eller vil du spørge andre brugere om produktet?

Side 1/2
GERMANY
C 10x
A 4x
B 5x
REAR
FRONT
4x
2,5
D 6x
1 Nm
1.
2.
3 Nm
4x
MANUAL SPEEDROCKER XL SET 12034
ALLROAD ROAD
01
EN EN . Scope of delivery . Fender-assembling front
EN . Mounting rubber inlay & Fastening with velcro
Frame protection foil
Required tools
Seatpost
EN
Fit the rubber inserts C
supplied to the fastening
adapters.
Note. Check for tight fit.
D 6x
02 03
04
EN
Place the SPEEDROCKER on the
bicycle frame and roughly align it.
Then remove the SPEEDROCKER
once again and stick the supplied
protective film onto the frame at D
the support points.
Note. The surface must be clean and
free of grease
EN
Position the SPEEDROCKER mount-
ing adapter on the protective film.
Thread the Velcro strap with the A
rubberized side facing the
frame and pull tight.
Note. Before each ride,
check for tight fit and clean
contact surfaces.
EN
Also attach the mounting adapters to
the bicycle fork with the protective
foils. Move the strut to the correct
position depending on the frame
size (1) and then tighten on the
adapter (2).
01
EN . Fender-assembling rear
EN . Mounting rubber inlays &
Fastening with velcro and rubber straps
EN
Fit the rubber inserts C supplied
to the fastening adapters.
Note. Check for tight fit.
GERMANY
3.
4.
2.1.
5.
1.
2.
Remove
MANUAL SPEEDROCKER XL SET 12034
ALLROAD ROAD
EN . Individual adaptations
02
EN
Place the SPEEDROCKER on the
bicycle frame and roughly align it.
Then remove the SPEEDROCKER
once again and stick the supplied
protective film D onto the frame
at the support points.
Note. The surface must be clean
and free of grease.
03
04
05
06
EN
Bring the SPEEDROCKER into position
and attach it to the seat tube in the
first step. To do this, thread the Velcro
strap B with the rubberized side
facing the seat tube over the protec-
tive film and tighten. If necessary,
slide the extendable extension profile
into the correct position.
EN
Position the SPEEDROCKER
mounting adapter on the protective
foil. Then thread the enclosed rubber
straps B through the opening on the
adapter and pull them forward. Then
fasten them there
via the eyelets.
EN
Depending on the requirements, the
struts can be easily shortened with
suitable tools.
EN
If your bike has a cable on the seat
tube, the extension profile must be
removed. Otherwise, the attachment
may cause damage to the cable.
07
EN
The Velcro and rubber straps B
can be shortened after attachment.
Note. Mount/shorten the velcro
and rubber straps so that they
cannot get caught in the wheel
while riding.


Produkt Specifikationer

Mærke: SKS
Kategori: Ikke kategoriseret
Model: Speedrocker XL SET

Har du brug for hjælp?

Hvis du har brug for hjælp til SKS Speedrocker XL SET stil et spørgsmål nedenfor, og andre brugere vil svare dig