Skylink 68 - remote Manual

Skylink Garageportåbner 68 - remote

Læs gratis den danske manual til Skylink 68 - remote (2 sider) i kategorien Garageportåbner. Denne vejledning er vurderet som hjælpsom af 20 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 10.5 anmeldelser. Har du et spørgsmål om Skylink 68 - remote, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Chamberlain®

Lift-Master®

Sears®

Wayne Dalton®

Master Mechanic®

Genie® (9 positions)

Genie® (12 positions)

Overhead Door®

Pulsar/Allister/Allstar®

Master Craft®

Linear®

M-O-M®

Stanley®

Multi-Code®

Skylink® UR-100

The model 68 transmitter

has 12 columns of posts,

each column has 3 posts.

(see diagram C)

2a. To program the model

68, open the case with

a coin. (see diagram B)

2b. There are 2 ways to pro-

gram the model 68 so

that it will communicate

with your garage door

opener. Open your exist-

ing transmitter, (the unit

you currently use to open

your garage), or look at

the back of your garage

door opener. If you see a

column of small switches

go to point 2c in this

manual. If there are no

switches, go to point 2e.

Diagram B

Each column contains one

connector (see digram D)

for a total of 12 connectors.

Diagram D

Diagram E

If the connector is placed

on the top and middle posts,

that column is set on “ + ”

or “ON” or “CLOSE”. If the

connector is placed on the

middle and bottom posts,

that column is set on “ - ”

or “OFF” or “OPEN”. If the

connector is removed

completely, (not placed

on any posts), it is set

to “ 0 ” or the neutral

position.(see diagram E

for examples of how to

set a column to the three

different positions). When

removing a connector to

set a column to the neu-

tral position, save the con-

nector in case you change

the code at a later date.

2c. To move the connectors,

slide an opened paper clip

into the side of a connector

and lift. (see diagram F)

When repositioning con-

nectors, place a connector

on the two chosen posts,

then push down on the

connector with your finger.

Paper

Clip

Diagram F

Diagram C

USA

CANADA

390

318

310

315

300

310

STEP 2 - SET CODE CONNECTORS

Linear *Position 1 to 8 + OR -

M-O-M *Position 1 to 8 + OR -

Stanley (310) Canada Position 1 to 10 + OR - 11,12 set to ‘+’ or ‘-’

Stanley (300) Position 1 to 10 + OR - 11,12 set to ‘+’ or ‘-’

Multi-Code Position 1 to 10 + OR - 11,12 set to ‘+’ or ‘-’

Chamberlain Position 1 to 9 +, 0 (blank), OR -

Lift-Master Position 1 to 9 +, 0 (blank), OR -

Sears Position 1 to 9 +, 0 (blank), OR -

Wayne Dalton Position 1 to 9 +, 0 (blank), OR -

Master Mechanic Position 1 to 9 +, 0 (blank), OR -

Genie (9 positions) Position 1 to 9 + OR -

Genie (12 positions) Position 1 to 12 + OR -

Master Craft Position 1 to 12 + OR -

Pulsar/Allister/Allstar Position 1 to 9 +, 0 (blank), OR -

Overhead Door Position 1 to 9 +, 0 (blank), OR -

Code connector setting to match your opener/motor

1a. Locate frequency

switch on the bottom

of the transmitter:

(see diagram A)

Diagram A

1b. Determine the brand of your garage door

opener and set the frequency switch to the

corresponding position. (see chart 1)

STEP 1 - SET FREQUENCY SWITCH

Thank you for your purchase of the Skylink garage door

remote control, Model 68. There are 2 different steps

you need to setup in order to use this universal garage

door remote control to operate your existing garage door

opener. These 2 steps are:

1) Frequency switch – select the correct frequency

according to the brand of your existing garage door

opener.

2) Code setting – Set the jumper connectors on the

Model 68 so that they match the code setting of your

existing garage door opener.

Please follow the detailed instructions below in order to set-

up the Skylink Model 68 to work with your existing opener.

NOTE: Transmission range may be reduced with use

on a metal garage door.

PROGRAMMING THE TRANSMITTER

Diagram G

Set the connectors numbered 1 through 12 to match the

switches of your existing transmitter or receiver. If your

garage door opener is manufactured by (Stanley®, Genie® ,

Multi-Code® , Linear® , Moore-O-Matic® ) these switches

may only have two positions, (“ +, ON, CLOSED” and “ - ,

OFF, OPEN”). (see diagram G) Set the connectors on the

model 68 to “ + ” if your existing switches are either “+ ,

ON, CLOSE ” and set to “ - ” if your existing switches are

either “ -, OFF, OPEN”. Do not use the center position “ 0 ”.

Examples of how to set Model 68

*Please check the FAQ section from www.skylinkhome.com for very old Linear / M-O-M systems.

Chart 1

390

300/390

390

318

310

300/310

390

D/A

D/C

315/390

318

315/390

310

390

C/A

Brand of your opener Set switch

to position Set switch

to position

Frequency Frequency

USA CANADA

Model 68

Existing

Transmitter

‘+’ or ‘ON’ or CLOSE ‘0’ = BLANK

‘-’ or ‘OFF’ or ‘OPEN’

STEP 2 - SET CODE CONNECTORS

BATTERYWARRANTY

If, within one year from date

of purchase, this product

should become defective

(except battery), due to

faulty workmanship or

materials, it will be repaired

or replaced, without charge.

Proof of purchase is

required.

12 volt " cigarette lighter "

type (size 23A) battery

(included).

2d. If your existing transmitter or receiver has fewer than 12 switches, match only the first corres-

ponding connectors. Leave the remaining posts blank, (remove the connectors).

2e. If your existing opener does not have any switches, then it can “learn”

the code needed to open your garage door. Set the connectors of the

model 68 to any combination of “ +, 0 , - ”. For security reasons, do not

leave the connectors at the current position (see point 2c on how tomove

the connectors). Press the learn button on the garage door opener (unit

with motor located in the ceiling of the garage, see diagram J) for appro-

ximately two seconds. The LED light located beside the learn button will

go on. Then press the button on the model 68 transmitter and hold for

about one second. The LED light on the garage door opener will flash

then go off.

The model 68 is now pro-

grammed correctly and will

open your garage door.

Diagram J ‘Learn’ Button

Garage Door

Opener (GDO)

STEP 2 - SET CODE CONNECTORS

Skylink will not be held

liable or responsible for

any misuse or application

of this product other than

for its intended use.

GARAGE DOOR/GATE

REMOTE CONTROL

USER'S INSTRUCTIONS

(Model 68)

® are registered trademarks of their respective corporations

CUSTOMER SERVICE

2213 Dunwin Drive

Mississauga, Ontario,

L5L 1X1, CANADÁ

(905)608-9223

(905)608-8744 FAX

Email:support@skylinkhome.com

(Reply within 24 hrs)

Customer Service : (800)304-1187

From Monday to Friday, 9am to 5pm EST

http://www.skylinkhome.com

P/N. 101A184-001 Rev.1

Patent no. D380895, 5680134,

5841390, 6005508

Patents Pending

Diagram I

If your garage door opener is manufactured by (Chamberlain®, Sears®, Lift-Master®, Wayne Dalton®, Pulsar® or Master

Mechanic® ) the switches will have 3 positions, (“+, 0, -”). Set the connectors on the model 68 to match their corresponding

positions.

If your opener is a Sears®, Chamberlain® or Lift-Master® and the existing transmitter has three buttons, (see diagram I), the first

connector in the model #68 may need to be changed to another position.

If your Chamberlain®, Sears®, Lift-Master® has 9 DIP switches, match them to the first 9 connectors on the model 68 and

remove the last 3 connectors (connectors 10, 11, 12). If there are only 8 DIP switches on your Chamberlain®,Sears®, Lift-

Master®, match them to the 2-9 position on the model 68 and remove the last 3 connectors

(connectors 10, 11, 12). Now you may have to change the positioning of the #1 connector

on the model 68.

If the large button of Diagram I is used to open the garage door, set the #1 connector to “ - ”

position. If the middle button is used, set the #1 connector to the “ 0 ” or “blank” position. If

the smaller button on the left is used, set the #1 connector to the “ + ” position.

Diagram H

Original Position

Reversed Position

If your existing transmitter has fewer

than 12 switches, see point 2d in this

manual. Press the button on the trans-

mitter. If the garage door does not open,

reverse all of the connectors on the

model 68. The “ + ” will be changed to

the “ - ” position and the “ - ” position

will be changed to the “ + ” position.

(see diagram H)

FCC

The Universal Garage Door Remote Control

is approved by the FCC and it complies with

Part 15 of the FCC Rules. Its operation is

subject to the following two conditions :

1. This device may not cause harmful inter-

ference.

2. This device must accept any interference

that may cause undesired operation.

WARNING:

Changes or modifications to this unit not

expressly approved by the party responsible

of compliance could void the user’s authority

to operate the equipment.

WARNING

If this transmitter triggers

other garage doors in

your neighborhood,

change all your trans-

mitters and receiver to a

new code setting.

DO NOT let children use

the garage door trans-

mitter without adult

supervision. Children

can injure themselves or

others by the garage

door.

NOTE

If your Skylink Universal Remote Control does not activate

your Garage Door Opener, the reason may be that your

GDO age or manufacturer is not listed on the compatibility

chart.

The solution is the Skylink UR-100 Universal Receiver.

If you would like to order Skylink’s product or have difficulty

getting your Skylink’s remote control to work, please :

1. visit our website FAQ at www.skylinkhome.com, or

2. email us at support@skylinkhome.com

(reply within 24 hrs)

3. call our toll free at 1-800-304-1187 from Monday to Friday,

9 am to 5 pm EST.

Produkt Specifikationer

Mærke:	Skylink
Kategori:	Garageportåbner
Model:	68 - remote

Har du brug for hjælp?

Hvis du har brug for hjælp til Skylink 68 - remote stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Garageportåbner Skylink Manualer

Skylink GT-100 Manual

26 August 2024

Skylink 68 - remote Manual

26 August 2024

Garageportåbner Manualer

Nyeste Garageportåbner Manualer

Chamberlain Liftmaster Manual

14 Januar 2025

LiftMaster 8500 Elite Manual

11 Januar 2025

Somfy Freevia Essential Manual

30 December 2025

Craftsman CMXZDCG4910 Manual

30 September 2024

Marantec Digital 302 Manual

30 September 2024

Marantec Comfort 270 Manual

30 September 2024

Marantec Command 181 Easywave Manual

22 September 2024

Novoferm Novomatic 803S Manual

22 September 2024

Somfy SOLAR - AKKU KIT Manual

20 September 2024

Berner K60 Manual

20 September 2024