SkyRC e430 Manual

SkyRC Batterioplader e430

Læs gratis den danske manual til SkyRC e430 (4 sider) i kategorien Batterioplader. Denne vejledning er vurderet som hjælpsom af 58 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 29.5 anmeldelser. Har du et spørgsmål om SkyRC e430, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

Thank you for your choice of the SKYRC e430, 100-240V AC balance charger. This unit is simple to use

but its operation does require some knowledge on the part of the user. Please read this entire operating

manual completely and attentively before using this product, as it covers a wide range of information on

operating and safety.

SKYRC e430 Charger is an economic, high quality 100-240V AC balance charger, designed for charging

LiPo and LiFe batteries from 2-4 cells in balance mode. The circuit power is 30W and max charge current

can reach to 3A. There are three kinds of charge current 1A/2A/3A that can be selected. You could select

the proper charge current according to battery capacity.

INSTRUCTION MANUAL

INTRODUCTION

CHARGE PROCEDURES

SKYRC e430 comes with the built in power supply. You can connect the AC power cord to the AC socket (100-240V AC)

directly.

Insert the AC power cord into the charger.

Insert the AC cord into a wall socket (100-240V). All LEDS will light for 1 second and the charge status LED will flash

green which indicates the charger is ready to charge.

Select the battery type LiPo/LiFe by the slide switch.

Select the proper charging current 1A/2A/3A by the slide switch.

Connect the battery main charge lead to battery socket which is in the front side of the charger and battery balance

wire to balance port which is in the right side of the charger.

The charger starts charging. The charge status LED and the cell status LED will glow constant red. If the battery

pack is 2-cell, Cell 1 and Cell 2 LEDs will glow constant red; if the battery pack is 3-cell, Cell 1, Cell 2 and Cell 3

LEDs will glow constant red; and so on.

During the charging progress, when the charge status LED glows constant red, the charger is charging in CC mode;

when the charge status LED glows constant orange, the charger is charging in CV mode;

When the cell LED is flashing, this cell is discharging

for balancing.

When the battery is fully charged, the charge status

LED will glow constant green.

Unplug the battery from the charger and the charge

status LED will flash green which indicates the

charger is ready to charge another battery.

Please refer to following steps to charge the battery,

- - - -1 2

SPECIFICATION

AC Input

Battery Type

Cell Count

Charge Current

Cell Terminate Voltage

Circuit Power

Current Drain for Balancing

Dimension

Weight

100-240V

LiPo/LiFe

2-4 cells

1A/2A/3A ± 10%

LiPo: 4.2V ± 0.02V / LiFe: 3.6V ± 0.02V

30W

200mA

69.4x110.7x40.5mm

193g

SK-100107

This diagram shows the correct way to connect

your battery.

Failure to connect as shown in this diagram will

damage this charger.

CAUTION:

10)

Battery Type Switch

Cell 2 LED Indicator

Cell 1 LED Indicator

Cell 4 LED Indicator

Cell 3 LED Indicator

Battery Socket

AC 100-240V

Power Jack

Charge Current Switch

Charge Status LED Indicator

Balance Socket

EXPLANATION OF LED STATUS

If there is an error, the charge status LED and one of the cell LED will blink in sequence.

* Error Message

LED green blinking

LED glows constant red

LED glows constant orange

LED glows constant green.

LED glows constant red.

LED flashes red

The charger is ready to charge.

The charger is charging in CC mode.

The charger is charging in CV mode.

The charging process finishes.

The cell is charging.

The cell is discharging.

Charge Status LED

Cell Status LED

In this case, please disconnect the power cord from the wall socket and unplug the battery from the charger.

Charge Status LED + Cell 1 LED

Charge Status LED + Cell 2 LED

Charge Status LED + Cell 3 LED

The voltage difference among cells is too big (more than 300mV)

Wrong connection

Low Voltage Protection(≤2.5V)

LED Status Error Message

CONNECTION DIAGRAM

LiPo

TO 100-240V AC

Socket

Cell LED will blink simultaneously

Charge Status Cell 1+2+3+4 LED

Cell 1+2 LED

The whole charging process exceeds 5 hours.

Battery type changed while charging.

Produkt Specifikationer

Mærke:	SkyRC
Kategori:	Batterioplader
Model:	e430

Har du brug for hjælp?

Hvis du har brug for hjælp til SkyRC e430 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Batterioplader SkyRC Manualer

SkyRC B6AC+ V2 Manual

17 August 2024

SkyRC SK-100059-01 Manual

16 August 2024

SkyRC B6 nano Manual

15 August 2024

SkyRC e680 Manual

14 August 2024

SkyRC iMAX B6mini Manual

13 August 2024

13 August 2024

12 August 2024

12 August 2024

12 August 2024

12 August 2024

Batterioplader Manualer

Nyeste Batterioplader Manualer

Savio LA-06 Manual

25 Oktober 2025

Goji GQICAR17C Manual

19 Oktober 2025

Tecmate Optimate 5 Voltmatic Manual

19 Oktober 2025

Sungrow IDC30E Manual

18 Oktober 2025

Sungrow SG33CX Manual

18 Oktober 2025

NEO Tools 11-890 Manual

15 Oktober 2025

Xtorm XPD06 Manual

13 Oktober 2025

Xtorm AU202 Manual

12 Oktober 2025

Alpha Tools A-ES 1000/1 Manual

12 Oktober 2025

Alpha Tools A-ES 1700/1 Manual

12 Oktober 2025