SkyRC E6 Manual

SkyRC Batterioplader E6

Læs gratis den danske manual til SkyRC E6 (2 sider) i kategorien Batterioplader. Denne vejledning er vurderet som hjælpsom af 37 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 19 anmeldelser. Har du et spørgsmål om SkyRC E6, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Thank you for your choice of the SKYRC e6, 100-240V AC balance charger. This unit is simple to use but

its operation does require some knowledge on the part of the user. Please read this entire operating

manual completely and attentively before using this product, as it covers a wide range of information on

operating and safety.

SKYRC e6 Charger is an economic, high quality 100-240V AC balance charger, designed for charging

LiPo and LiFe batteries from 2-6 cells in balance mode. The circuit power is 50W and max charge current

can reach to 5A. There are four kinds of charge current 1A/2A/4A/5A that can be selected. You could

select the proper charge current according to battery capacity.

INSTRUCTION MANUAL

INTRODUCTION

CHARGE PROCEDURES

SKYRC e6 comes with the built in power supply. You can connect the AC power cord to the AC socket

(100-240V AC) directly.

Note: This charger can charge LiPo and LiFe batteries ONLY in balance mode. In this case, you must use

balance board to connect the charger with the battery.

Insert the AC power cord into the charger.

Insert the AC cord into a wall socket (100-240V). All LEDS will light for 1 second and the charge

status LED will flash green which indicates the charger is ready to charge.

Select the battery type LiPo/LiFe by the toggle switch.

Select the proper charging current 1A/2A/4A/5A by the toggle switch.

Connect the battery to the charger main battery lead to battery socket and balance wires to balance

socket.

The charger starts charging. The charge status LED and the cell status LED will glow constant red. If

the battery pack is 2-cell, Cell 1 and Cell 2 LEDs will glow constant red; if the battery pack is 3-cell,

Cell 1, Cell 2 and Cell 3 LEDs will glow constant red; and so on.

During the charging progress, when the charge

status LED glows constant red, the charger is

charging in CC mode; when the charge status

LED glows constant orange, the charger is

charging in CV mode;

When the cell LED is flashing, this cell is

discharging for balancing.

When the battery is fully charged, the charge

status LED will glow constant green.

Unplug the battery from the charger and the

charge status LED will flash green which

indicates the charger is ready to charge

another battery.

Please refer to following steps to charge the battery,

EXPLANATION OF LED STATUS

If the charger encounters a problem, all LEDs will flash red in sequence to alert you to the errors. In this

case, please disconnect the power cord from the wall socket and unplug the battery from the charger.

* Error Message

- 1 - - 2 -



SPECIFICATION

AC Input

Battery Type

Cell Count

Charge Current

Circuit Power

Current Drain for Balancing

Dimension

Weight

Charger/Cell Status

100-240V

LiPo/LiFe

2-6 cells

1A/2A/4A/5A ± 10%

50W

200mA

82.7x140.5x45.7mm

310g

SK-100052

This diagram shows the correct way to connect your

battery to the e6 charger while charging in balance

mode.

Failure to connect as shown in this diagram will

damage this charger.

The main battery leads must be connected along with

the balance lead connector as shown before charging

your battery.

CAUTION:

LED flashes green

LED glows constant red

LED glows constant orange

LED glows constant green.

LED glows constant red.

LED flashes red

The charger is ready to charge.

The charger is charging in CC mode.

The charger is charging in CV mode.

The charging process finishes.

The cell is charging.

The cell is discharging.

Charge Status LED

Cell Status LED

CONNECTION DIAGRAM

Battery Type Switch

Cell 3 LED Indicator

Cell 2 LED Indicator

Cell 1 LED Indicator

Cell 6 LED Indicator

Cell 5 LED Indicator

Cell 4 LED Indicator

Charge Current Switch

Charge Status LED Indicator

Battery Socket

Balance Socket

100-240V

Power Jack

Charger

Balance

Adaptor

Battery

10)

Produkt Specifikationer

Mærke:	SkyRC
Kategori:	Batterioplader
Model:	E6
Type:	Indendørs batterioplader
Bredde:	82.7 mm
Dybde:	140.5 mm
Højde:	45.7 mm
Vægt:	310 g
Antal pr. pakke:	1 stk
Produktfarve:	Sort
Indgangsspænding:	100-240 V
Indgangsfrekvens:	50/60 Hz
Antal battericeller:	6
Kompatible batteri-teknologier:	Lithium polymer (LiPo)
Udgang:	50W
Aktuel opladning:	1A, 2A, 4A, 5A