Skytec SP1200A Manual
Skytec
Højttaleranlæg
SP1200A
Læs gratis den danske manual til Skytec SP1200A (9 sider) i kategorien Højttaleranlæg. Denne vejledning er vurderet som hjælpsom af 19 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 10 anmeldelser. Har du et spørgsmål om Skytec SP1200A, eller vil du spørge andre brugere om produktet?
Side 1/9

SP Hi-End Active Speaker Series
170.310 / 170.311 / 170.306 / 170.313 / 170.316
INSTRUCTION MANUAL
HANDLEIDING
MODE D’EMPLOI
BEDIENUNGSANLEITUNG
MANUAL DE INSTRUCCIONES

4 - 18
INPUT PANEL
8” & 10” Versie:
1. Input connector for microphone
2. Volume control for the microphone
3. Volume control for the line input
4. Line input connector for the audio input source e.g. mixer, CD
player, etc.
5. Output connector to a second box or amplifier (line level)
6. Tone control for the output
12” & 15” Versie:
1. Input connector for microphones
2. Volume control for the microphone
3. Volume control for the line input
4. Volume control for the output
5. Tone control for the output
6. Output connector to a second box or amplifier (line level)
7. Line input connector for the audio input source e.g. mixer, CD
player, etc.
TROUBLESHOOTING
One certain method of determining if a speaker is faulty is to substitute a speaker that is known to work
correctly for the suspected problem speaker. If the “normally correct speaker” is experiencing the same
difficulties or problems as the suspected problem speaker, use the information below to isolate the problem.
Possible cause Action
No output
Cables Reseat all connectors
Substitute known good cables
Check solder joins
Inspect cable for damage
Inspect wire or connector for stray strand that may short
Intermittent
Poor connections While it is possible for a faulty speaker to exhibit intermittent output, it’s more likely
that an output cable/connector is the problem. Check the soldering on your
connectors.
Constant noise, buzzing and/or humming
Faulty electronic Any constant noise originates in the amplifier, mixer, signal processing, source
device in the signal devices, or line-level wiring. Check and correct system grounding as required. chain
check for noisy sources or electronic components. Check wiring for shielding.
Poor low-frequency output
Improper polarity When two speakers in close proximity to each other are connected out-of-polarity,
they can partially cancel each other out, especially at low frequencies. Check your
speaker cables to be sure they are all identically wired and connected. Check the
balanced line signal cables to be sure they are all correctly wired.
Do not attempt to make any repairs yourself. This would invalid your warranty. Do not make any changes to the unit. This
would also invalid your warranty. The warranty is not applicable in case of accidents or damages caused by inappropriate use
or disrespect of the warnings contained in this manual. Tronios cannot be held responsible for personal injuries caused by a
disrespect of the safety recommendations and warnings. This is also applicable to all damages in whatever form.
Produkt Specifikationer
Mærke: | Skytec |
Kategori: | Højttaleranlæg |
Model: | SP1200A |
Har du brug for hjælp?
Hvis du har brug for hjælp til Skytec SP1200A stil et spørgsmål nedenfor, og andre brugere vil svare dig
Højttaleranlæg Skytec Manualer
16 August 2024
15 August 2024
15 August 2024
15 August 2024
15 August 2024
14 August 2024
13 August 2024
13 August 2024
13 August 2024
13 August 2024
Højttaleranlæg Manualer
- Monacor
- Vorago
- Anchor Audio
- Korg
- Muse
- Yamaha
- Naxa
- Karma
- Sennheiser
- Pure Acoustics
- Trust
- Majestic
- Pyle
- Trevi
- DAP-Audio
Nyeste Højttaleranlæg Manualer
12 Juni 2025
2 Juni 2025
5 September 2024
3 September 2024
27 August 2024
27 August 2024
27 August 2024
27 August 2024
27 August 2024
27 August 2024