Skytech 3002 Manual

Skytech Diverse klimastyring 3002

Læs gratis den danske manual til Skytech 3002 (10 sider) i kategorien Diverse klimastyring. Denne vejledning er vurderet som hjælpsom af 8 personer og har en gennemsnitlig bedømmelse på 3.9 stjerner ud af 4.5 anmeldelser. Har du et spørgsmål om Skytech 3002, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/10

INSTALLATION AND OPERATING INSTRUCTIONS

IF YOU CANNOT READ OR UNDERSTAND THESE INSTALLATION INSTRUCTIONS DO NOT ATTEMPT

TO INSTALL OR OPERATE

Model: 3002

INTRODUCTION

This SKYTECH remote control system was developed to provide a safe, reliable, and user-friendly remote control system for gas

heating appliances. The system can be operated thermostatically or manually from the transmitter. The system operates on radio

frequencies (RF) within a 20-foot range using non-directional signals. The system operates one of 1,048,576 security codes that are

programmed into the transmitter at the factory; the remote receiver’s code must be matched to that of the transmitter prior to initial use.

Review COMMUNICATION SAFETY under theTRANSMITTER SECTION and THERMO SAFETY under the REMOTE RECEIVER

SECTION. These signal/temperature safety features shut down the appliance when a potentially unsafe condition exists.

REV. 4-19-12 Page 1

Skytech: 3002

The transmitter operates on (2) AAA-size 1.5V batteries. It is recommended that ALKALINE batteries always be used for

longer battery life and maximum operational performance. IMPORTANT: New or fully charged batteries are essential for

proper operation of the multi-function transmitter. Insert (2) AAA-size 1.5 V batteries into the battery compartment on the

back of the transmitter, positioning the (+) and (-) ends of the batteries as indicated on the casing. When the batteries are

inserted, gure #2 (with similar numbers) will display.

Fig. 1 Transmitter Front and Back Views

Note: If a LOW battery icon appears on the screen,

check the position of the batteries.

CAUTION: Due to the sensitive temperature-monitoring

components in the transmitter, it may be necessary to

allow the transmitter to stabilize to room temperature

before accurate room temperatures are displayed on

the screen. If the transmitter is activated from a

severe cold condition, it can take up to fteen minutes

for accurate temperature readings to appear.

1. BATTERY ICON - Symbol means battery power is low. Replace batteries within 2-weeks.

2. TIMER- Indicates time remaining before system shuts OFF, when timer-programmed; 9-hour maximum setting.

3. MODE- Indicates operation MODE of system. ON indicates the system is manually ON. OFF indicates the entire

system is turned OFF and THERMO indicates the system will automatically cycle ON/OFF, depending on the SET

temperature.

4. SET- Indicates desire SET room temperature for THERMO operation.

5. FLAME – Indicates burner/valve in ON position.

6. CLOCK – Indicates the current time in AM/PM

7. ROOM – Indicates CURRENT room temperature.

8. °F indicates degrees Fahrenheit (°C indicates degrees Celsius).

LCD DISPLAY FUNCTIONS

ROOM

SET

Fig. 2 LCD Display Functions

MODE

COVER CLOSED

MODE

TIMER

TIME

SET

SLIDE COVER

OPEN

AAA

BACK OF

TRANSMITTER

Skytech: 3002 REV. 4-19-12 Page 2

BASIC TRANSMITTER FUNCTIONS

To understand the operation of the transmitter, press and release the MODE button (Fig. 3) until the LCD screen reads

OFF in the display (Fig. 4).

Step 1: Press the MODE button one time to manually turn ON the appliance (Fig. 5).

Step 2: Press the MODE button a second time to put the to put the system in THERMO mode (Fig. 6).

Step 3: Press the MODE button a third time to turn the appliance back OFF again as show in (Fig. 4).

Fig. 4 OFF Mode

ROOM

SET

Fig. 5 Manual ON

ROOM

SET

Fig. 6 Thermo Mode

ROOM

SET

Slide down the lower section of the cover on the front of the transmitter to expose the “SET” buttons (Fig. 1). The slide

cover protects the SET buttons from being changed accidentally. Close the cover after completing the following settings/

programming.

Blinking numbers on the LCD display indicate the system is awaiting user input, such as using the UP and DOWN buttons

to program a new setting. If no change is made to ashing digits within 15-seconds, the system will complete the

procedure last programmed and reset the display to its normal state.

SETTING UP THE TRANSMITTER

SETTING THE CLOCK

1. Press and hold the TIMER/TIME button on the transmitter

for more than 2-seconds (Fig. 7). The hour digit(s) will begin

blinking (Fig. 8)..

2. Press the UP or DOWN button until the desired hour is

displayed in AM or PM.

3. After setting the desired hour, press and release the TIMER/

TIME button again to set the minutes; the minute digits will

begin blinking (Fig. 9)..

4. Press the UP or DOWN button until the desired minutes are

displayed.

5. Press and hold the TIMER/TIME button again for more than

2-seconds. The time digits will cease blinking, indicating the

clock has been successfully set. You may also press the

SET button on the transmitter to stop the time digits from

blinking and set the time.

ROOM

SET

ROOM

SET

Fig. 8 SettingHours Fig. 9 Setting Minutes

Fig. 3 Mode Button

MODE

Fig. 7 Timer/Time Button

MODE

TIMER

TIME

SET

Produkt Specifikationer

Mærke:	Skytech
Kategori:	Diverse klimastyring
Model:	3002

Har du brug for hjælp?

Hvis du har brug for hjælp til Skytech 3002 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Diverse klimastyring Skytech Manualer

Skytech 3002 Manual

1 August 2024

Diverse klimastyring Manualer

Nyeste Diverse klimastyring Manualer

Elco LOGON B SOL Zonneregelaar Manual

5 Oktober 2024

Junkers Storacell PF 1000 solar Manual

19 September 2024

Junkers Storacell SK 160 Manual

18 September 2024

Elco LOGON SOL plus Zonneregelaar Manual

17 September 2024

Ygnis TOTALECO TURBO Diversen klimaatbeheersing Manual

13 September 2024

Oregon Scientific BA169 weer hub Manual

27 August 2024

Riello BGK0.1 Manual

27 August 2024

Premix XR-Serie Manual

26 August 2024

Elektrobock RJ 402 Manual

26 August 2024

Elektrobock RJ 401 Manual

26 August 2024