Speaka 989272 Manual


Læs gratis den danske manual til Speaka 989272 (44 sider) i kategorien Vægbeslag. Denne vejledning er vurderet som hjælpsom af 27 personer og har en gennemsnitlig bedømmelse på 3.6 stjerner ud af 14 anmeldelser. Har du et spørgsmål om Speaka 989272, eller vil du spørge andre brugere om produktet?

Side 1/44
Diese Bedienungsanleitung ist eine Publikation der Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
Alle Rechte einschließlich Übersetzung vorbehalten. Reproduktionen jeder Art, z. B. Fotokopie, Mikrover lmung, oder die Erfassung
in elektronischen Datenverarbeitungsanlagen, bedürfen der schriftlichen Genehmigung des Herausgebers. Nachdruck, auch auszugs-
weise, verboten.
Diese Bedienungsanleitung entspricht dem technischen Stand bei Drucklegung. Änderung in Technik und Ausstattung vorbehalten.
© Copyright 2012 by Conrad Electronic SE.
Version 11/12
B E D I E N U N G S A N L E I T U N G
TV-Wandhalter 81-152 cm (32-60”) starr
Best.-Nr.: 98 92 72
Bestimmungsgemäße Verwendung
Der TV-Wandhalter dient zur Montage von geeigneten TV-Geräten an Wänden.
Das TV-Gerät darf die in den „Technischen Daten“ angegebenen Werte für TV-Größe und Gewicht nicht
überschreiten.
Eine andere Verwendung als zuvor beschrieben führt zur Beschädigung dieses Produktes oder des TV-Ge-
rätes und ist darüber hinaus mit Gefahren, wie z.B. Beschädigung von Möbeln in der Nähe des Wandhalters,
Verletzung von Personen etc. verbunden.
Das Produkt darf nicht geändert bzw. umgebaut werden.
Die Sicherheitshinweise sind unbedingt zu befolgen.
Lieferumfang
Siehe Bild 1 auf dem Beilageblatt zu dieser Anleitung.
Sicherheitshinweise
Bei Schäden, die durch Nichtbeachten dieser Bedienungsanleitung verursacht werden,
erlischt die Gewährleistung/Garantie. Für Folgeschäden übernehmen wir keine Haftung.
Bei Sach- oder Personenschäden, die durch unsachgemäße Handhabung oder Nichtbe-
achten der Sicherheitshinweise verursacht werden, übernehmen wir keine Haftung. In
solchen Fällen erlischt die Gewährleistung/Garantie.
Das Symbol mit dem Ausrufezeichen weist auf wichtige Hinweise in der Bedienungsanlei-
tung hin.
Das Symbol mit dem Pfeil kennzeichnet Tipps und Hinweise
Ein TV-Wandhalter ist kein Spielzeug. Halten Sie deshalb Kinder von dem Produkt fern.
Lassen Sie das Verpackungsmaterial nicht achtlos liegen. Es könnte für Kinder zu einem gefährlichen
Spielzeug werden.
Die Wahl eines nicht geeigneten Montageortes kann zu Personen- oder Sachschäden führen.
Gehen Sie beim Zusammenbau bzw. bei der Montage vorsichtig vor. Das Produkt kann teilweise scharfe
Kanten haben. Hier besteht Verletzungsgefahr!
Führen Sie nur die zur Montage (bzw. Einstellung) des TV-Wandhalters erforderlichen Arbeiten durch. Füh-
ren Sie niemals Umbauarbeiten oder Reparaturversuche durch.
Prüfen Sie vor Beginn der Montage, ob auf der Rückseite des TV-Gerätes geeignete Befestigungsmöglich-
keiten für den TV-Wandhalter vorhanden sind.
Abhängig von der Größe und Bauart des TV-Gerätes und des TV-Wandhalters ist es sinnvoll, wenn eine
zweite Person bei der Montage hilft. Diese kann z.B. das TV-Gerät festhalten, während Sie das TV-Gerät
am Wandhalter befestigen.
Führen Sie die Montage sehr gewissenhaft durch, da ein Herabfallen von TV-Gerät und TV-Wandhalter
nicht nur zu teuren Folgeschäden führen kann, sondern außerdem erhöhte Verletzungsgefahr besteht!
Verlegen Sie alle Kabel des TV-Gerätes so, dass sie nicht im Wandhalter eingequetscht oder geknickt werden.
Überlasten Sie den TV-Wandhalter nicht. Achten Sie auf die Angaben des Herstellers zu Maximalgewicht
des TV-Gerätes bzw. Baugröße.
Benutzen Sie den TV-Wandhalter nicht, um sich abzustützen oder sich daran festzuhalten.
Befestigen Sie keine anderen Gegenstände am TV-Wandhalter als das dafür vorgesehene TV-Gerät.
Im Zweifelsfall sollten Sie die Montage nicht selbst durchführen. Überlassen Sie dies einer Fachkraft.
Montage
Die Wandmontage ist nur dann zulässig, wenn die Wandbeschaffenheit dafür geeignet
ist. Dünne Leichtbauwände oder Gipskartonplatten sind normalerweise ungeeignet. Im
Fachhandel gibt es jedoch u.U. spezielle Dübel für solche Montageorte. Fragen Sie im
Zweifelsfall vor der Montage einen Fachmann.
Je nach Untergrund (z.B. Beton) ist dafür geeignetes Montagematerial zu verwenden
(Schrauben, Dübel usw.). Die beiliegenden Dübel sind ausschließlich für massive Wände
geeignet. Spezielle Dübel und Schrauben liegen dem TV-Wandhalter nicht bei und müssen
in Abhängigkeit von der Wandbeschaffenheit separat erworben werden.
Aufgrund des Gewichts von TV-Gerät, TV-Wandhalter und der Hebelwirkung ist auf eine
stabile Befestigung zu achten.
Planen Sie den Montageort sorgfältig, so dass sich der TV-Wandhalter mit dem daran be nd-
lichen TV-Gerät nach der Montage in der gewünschten Lage (Höhe und Position) be ndet.
Achten Sie beim Bohren bzw. Festschrauben darauf, dass keine Kabel oder Leitungen in
der Wand beschädigt werden. Werden versehentlich Elektroleitungen angebohrt, besteht
Lebensgefahr durch einen elektrischen Schlag!
Achten Sie beim Umgang mit elektrischen Werkzeugen (z.B. einer Bohrmaschine) auf Ihre
Sicherheit. Beachten Sie die Sicherheitshinweise in den entsprechenden Anleitungen.
Stellen Sie sicher, dass sich während der Montage keine Personen im Bereich unter dem
TV-Wandhalter bzw. dem TV-Gerät be nden.
Beachten Sie bitte die Bilder auf dem Beilageblatt zu dieser Anleitung.
Vorbereitung des TV-Gerätes
In der Regel muss vor der Befestigung der vorhandene Standfuß des TV-Gerätes entfernt werden. Beach-
ten Sie hierzu die Bedienungsanleitung Ihres TV-Gerätes.
Legen Sie das TV-Gerät ach mit der Displayseite nach unten auf eine weiche und saubere Unterlage.
Auf das Display darf kein Druck ausgeübt werden. Schützen Sie wertvolle Möbelober ächen während der
Montage mit einer geeigneten Unterlage.
Entfernen Sie den vorhandenen Standfuß. Je nach TV-Gerät ist dieser festgeschraubt oder eingeclipst.
Bild 2
Legen Sie am Montageort die Position und die Höhe des Befestigungsrahmens fest.
Richten Sie den Befestigungsrahmen mit Hilfe der integrierten Libelle waagerecht aus.
Zeichnen Sie die erforderlichen Bohrungen an der Montage äche an. Benutzen Sie den Befestigungsrah-
men hierbei als Schablone.
Bohren Sie die erforderlichen Löcher und versehen Sie die Bohrungen mit geeigneten beln (B bzw.
Spezialdübel).
Schrauben Sie den Befestigungsrahmen mit geeigneten Schrauben (A bzw. zu den Dübeln passende
Schrauben) und Beilagscheiben (C) fest.
Bild 3
Befestigen Sie die beiden Montagebügel mit passenden Schrauben (D-G) und Beilagscheiben (N bzw. O)
an der Rückseite Ihres TV-Gerätes.
Achten Sie bei der Bügelmontage darauf, dass die Klickverschlüsse an den Bügeln zur TV-Unterseite wei-
sen müssen.
Bei der Befestigung der Montagebügel ist unbedingt darauf zu achten, dass die richtigen
Schrauben verwendet werden. Diese müssen nicht nur das zum TV-Gerät passende Gewin-
de haben, sondern dürfen nicht zu lang sein, da andernfalls das TV-Gerät beschädigt wird.
Die Schrauben dürfen jedoch auch nicht zu kurz sein, da andernfalls keine sichere Ver-
bindung besteht. Sie sollten mit mindestens 5 vollständigen 360°-Gewindegängen in die
entsprechenden Gewinde des TV-Gerätes eingeschraubt werden.
Sollten Sie Zweifel über die richtige Schraubenlänge haben, so empfehlen wir Ihnen, sich
mit dem TV-Hersteller oder einem entsprechenden Fachmann in Verbindung zu setzen.
Wenden Sie beim Festschrauben keine Gewalt an, da hierdurch das TV-Gerät zerstört werden kann, Ver-
lust von Gewährleistung/Garantie!
Sollte Ihr TV-Gerät eine gewölbte Rückseite haben oder der Wandabstand aus anderen Gründen erhöht
werden müssen, können Sie zwischen TV-Gerät und Montagebügel Distanzstücke (L bzw. M) einfügen. In
diesem Fall müssen die längeren Schrauben (H-K) zur Befestigung verwendet werden.
Bild 4
Heben Sie das TV-Gerät mit den montierten Bügeln von oben auf den Befestigungsrahmen. Hierbei muss
das TV-Gerät mit der Oberseite leicht zur Wand geneigt werden.
Die oberen Raster der Befestigungsbügel ssen sauber in das Pro l des Befestigungsrahmens einrasten.
Richten Sie das TV-Gerät mittig auf dem Rahmen aus und kippen Sie es, bis es am unteren Teil des Befes-
tigungsrahmens anliegt.
Ziehen Sie an den Schlaufen der Sicherungsbänder, damit die unteren Rasten in den Befestigungsrahmen
einrasten können.
Wartung und P ege
Das Produkt ist wartungsfrei und bedarf abgesehen von einer gelegentlichen Reinigung mit einem weichen,
trockenen Tuch keinerlei P ege.
Verwenden Sie auf keinen Fall aggressive Reinigungsmittel oder chemische Lösungen, da ansonsten die
Gehäuseober ächen beschädigt werden könnten.
Technische Daten
TV-Größe .....................................81-152 cm (32-60“)
Belastbarkeit ................................max. 45 kg
VESA-Befestigung .......................max. 600 x 400
Wandabstand...............................16 mm
Material ........................................ Stahl
O P E R A T I N G I N T R U C T I O N S
These operating instructions are a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, micro lming, or the capture in electronic data
processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited.
These operating instructions represent the technical status at the time of printing. Changes in technology and equipment reserved.
© Copyright 2012 by Conrad Electronic SE.
Version 11/12
TV wall bracket 81-152 cm (32-60”) xed
Item no. 98 92 72
Intended use
The TV wall bracket is used to install suitable TV sets on walls.
The TV set should not exceed the size and weight values speci ed in “Technical Data”.
Any use other than the one described earlier can damage this product or the TV set, and is associated with
risks such as damage to furniture in the vicinity of the wall bracket, physical injury to persons etc.
No part of the product may be modi ed or altered.
The safety instructions must be observed at all times.
Package Contents
See Figure 1 on the sheet attached to this manual.
Safety Instructions
The warranty will be void in the event of damage caused by failure to observe these safety
instructions! We will not assume liability for any resulting damage.
We shall not accept liability for damage to property or personal injury caused by incorrect
handling or non-compliance with the safety instructions. In such cases, the warranty will
be null and void.
The exclamation mark symbol indicates important information in these operating instruc-
tions.
The arrow symbol denotes tips and instructions
A TV wall bracket is not a toy. Keep the device out of the reach of children.
Do not leave packaging material lying around carelessly. They may become dangerous playthings for chil-
dren.
Selecting an unsuitable installation location can lead to personal or material damage.
Proceed with care when assembling and installing the product. The product can have sharp edges. There
is risk of injury!
Only perform work that is necessary for the installation (or adjustment) of the TV wall bracket. Never attempt
alterations or repairs.
Before starting the installation process, check whether there are appropriate mounting options for the TV
wall bracket on the rear of your TV set.
Depending on the size and design of the TV set and TV wall bracket, a second person should help with the
installation. This person can for example, hold the TV set when you mount the TV set on the wall bracket.
Apply your full concentration when carrying out the installation, because if the TV set and/or TV wall bracket
falls, this could cause expensive consequential damage to the equipment and there is increased risk of
personal injury!
Route all the TV set’s cables in such a way that they do not get jammed or kinked in the TV wall bracket.
Do not overload the TV wall bracket. Pay attention to the details provided by the manufacturer for the
maximum weight and/or size of the TV set.
Do not use the TV wall bracket to support yourself or hold on to it.
Do not mount any object on the TV wall bracket other than the TV set intended for it.
In case of uncertainty, do not perform the installation on your own. Engage a skilled person to do the job.
Installation
Wall-mounting is permissible only if the wall concerned is of the correct type and con-
dition. Lightweight partition walls or those made from gypsum boards are normally un-
suitable. However, specialist retailers do sometimes stock special dowel ttings for such
installation locations. If you are in doubt, ask a specialist before installation.
Suitable mounting materials must be used (screws, dowels, etc.), depending on the base
wall material (e.g. concrete). The attached dowels are suitable exclusively for solid walls.
Special dowels and screws do not come with the TV wall bracket and must be purchased
separately, depending on the quality of the wall.
Due to the weight of the TV set, the TV wall bracket and the lever action involved, ensure
that screws are xed securely.
Plan the installation location carefully so that the TV wall bracket holding the TV set is in the
desired position (height and position) after the installation.
When drilling holes and tightening screws, ensure that no cables or pipes are damaged. If
electric cables are drilled through inadvertently, there is danger of fatal electric shock!
Pay special attention to your safety when using electric tools (e.g. a drill). Heed the safety
instructions in the corresponding chapters of this manual.
During installation, ensure that no persons are located under the TV wall bracket or under
the TV set.
Please follow the gures on the sheet attached to this manual.
Preparation of the TV set
Normally, the existing stand of the TV set must be removed before mounting it on the TV wall bracket.
Observe the operating instructions for your TV set.
Place the TV set atly with the screen facing downwards on a soft and clean supporting base. Do not exert
any pressure on the screen. Protect valuable furniture surfaces during installation by using a suitable pad
or cloth.
Remove the existing stand. It is either screwed tightly or clipped, depending on the TV set.
Figure 2
De ne the position and height of the mounting frame at the installation location.
Adjust the mounting frame horizontally with the help of the integrated spirit level.
Mark the necessary drilling holes on the mounting surface. Use the mounting frame as stencil.
Drill the required holes and provide them with suitable dowels (B or special dowel).
Fix the mounting frame with suitable screws (A or screws tting the dowels) and at washers (C).
Figure 3
Fix the two installation clamps with suitable screws (D-G) and at washers (N or O) on the rear side of your
TV set.
When installing the clamps, ensure that the snapping interlocks on the aps point to the bottom of the TV
set.
When xing the installation clamps at the rear of the TV set, make absolutely certain that
you use the correct screws. Not only must these have the correct thread type for the TV set,
but they must also not be too long; as otherwise the TV set may be damaged.
However, the screws must not be too short, as otherwise the connection will not be
secure. They must be screwed into the corresponding threads of the TV set with at least
5 full 360° turns.
If you have any doubt about the correct length of the screws, contact the manufacturer of
the TV set or an appropriate specialist.
Do not use any force when tightening the screws; otherwise the TV set may be destroyed, leading to loss
of warranty/guarantee!
If your TV set has an arched rear, or the distance from the wall must be increased for other reasons, you
can insert spacers (L or M) between the TV set and the installation clamp. In this case, the longer screws
(H-K) must be used for the mounting.
Figure 4
Lift the TV set with the installed clamps from the top on to the mounting frame. The TV set must be inclined
slightly towards the wall.
The upper grids of the mounting clamp must engage cleanly in the section of the mounting frame.
Align the TV set at the centre of the frame and tilt it until it is supported by the lower part of the mounting
frame.
Pull the loops of the safety strap, so that the lower grids may engage in the mounting frame.
Maintenance and Care
The product does not have to be serviced and, except for occasional cleaning with a soft, dry cloth, requires
no maintenance whatsoever.
Never use aggressive cleaning agents or chemical solutions as these may damage the surface of the case.
Technical Data
TV size .........................................81-152 cm (32-60“)
Load capacity ..............................max. 45 kg
VESA mount ................................max. 600 x 400
Wall distance ...............................16 mm
Material ........................................ steel
O P E R A T I N G I N T R U C T I O N S


Produkt Specifikationer

Mærke: Speaka
Kategori: Vægbeslag
Model: 989272

Har du brug for hjælp?

Hvis du har brug for hjælp til Speaka 989272 stil et spørgsmål nedenfor, og andre brugere vil svare dig




Vægbeslag Speaka Manualer

Speaka

Speaka 631819 Manual

17 Juni 2024
Speaka

Speaka 989272 Manual

17 Juni 2024
Speaka

Speaka 631820 Manual

17 Juni 2024
Speaka

Speaka 989930 Manual

17 Juni 2024
Speaka

Speaka 989273 Manual

17 Juni 2024

Vægbeslag Manualer

Nyeste Vægbeslag Manualer