SSV Works X3-US10 Manual

SSV Works Højttaler X3-US10

Læs gratis den danske manual til SSV Works X3-US10 (5 sider) i kategorien Højttaler. Denne vejledning er vurderet som hjælpsom af 21 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 11 anmeldelser. Har du et spørgsmål om SSV Works X3-US10, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/5

X3-US10

2016+ Can-Am Maverick x3

10” Under Seat Enclosure

SSV WORKS, 201 N. Rice Ave Unit A, Oxnard, CA 93030

www.SSVworks.com | Phone: 818-991-1778 | Fax: 866-293-6751

Please read and understand these

instructions completely before

installation to avoid possible injury, or

damage to the accessory or vehicle.

WARRANTY INFORMATION:

All SSV Works enclosures are covered by a limited lifetime warranty against defects

in material or workmanship. All SSV Works Electronics are covered by a limited 1 year

warranty against defects in material or workmanship. All SSV Works Speakers are

covered by a limited 1 year warranty against defects in material or workmanship. Labor

for replacement of defective components is not covered. Contact SSV Works for further

warranty information.

1. X3-US10 Enclosure

2. M6 x 16mm Screws x 10

3. M6 Washers x 10

4. M6 x 25mm Screw x 1

TOOLS NEEDED FOR INSTALLATION PARTS LIST

PARTS LIST IMAGES

5. Large washers x 2

6. D-Brackets x 2

7. A-Bracket x 1

8. B-Bracket x 1

2. M6 x 16mm Screws x 10

7. A-Bracket x 1

11. M6 Locking Hex Nut

8. B-Bracket x 1

12. Foam Strips x 3

3. M6 Washers x 10 4. M6 x 25mm Screw x 1

5. Large washers x 2

9. Seat Risers x 2

1. X3-US10 Enclosure

6. D-Brackets x 2

10. Small Spacer x 1

- 10mm Socket or Wrench

- T-30 Torx Driver

- T-40 Torx Driver

9. Seat Risers x 2

10. Small Spacer x 1

11. M6 Locking Hex Nut

12. Foam Strips x 3

A. Apply the foam strips to the inside right, left and top side of

the enclosure.

C. Remove the factory 10mm nut and bolt from the brake line. Place the washer on top of the factory bracket and push the long M6x25mm screw through

the top. Then attach the brake line, spacer, washer and nut. T hen hand tighten.

B. Using the supplied M6 screws and washers, screw the DD-brackets

to the bottom right and left side of the enclosure.

X3-US10

C C C

SSV HOLE PATTERN

KICKER HOLE PATTERN

FOR UNLOADED ENCLOSURES:

Pink hole pattern: SSV Works Subwoofer

Blue hole pattern: Kicker Subwoofer

If using a different brand subwoofer,

rst see if the subwoofer holes line up

with either one of the pre-drilled hole

patterns. If not, make sure to drill new

holes away from the pre-drilled holes.

Be sure to use the 8 supplied SSV Works

#7 screws when installing your own

subwoofer. #7 Screws x 8

Produkt Specifikationer

Mærke:	SSV Works
Kategori:	Højttaler
Model:	X3-US10

Har du brug for hjælp?

Hvis du har brug for hjælp til SSV Works X3-US10 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Højttaler SSV Works Manualer

SSV Works BR-2B65U Manual

24 August 2024

SSV Works BR-B65 Manual

24 August 2024

SSV Works WP-RZO + 2 Manual

24 August 2024

SSV Works RG4-SB10 Manual

24 August 2024

SSV Works BR-2B65A Manual

24 August 2024

SSV Works X3-US10 Manual

24 August 2024

SSV Works US2-C65 Manual

24 August 2024

SSV Works RZ4-3KRC Manual

24 August 2024

SSV Works RG4-F65K Manual

24 August 2024

SSV Works RZ3-1KRC Manual

24 August 2024

Højttaler Manualer

Nyeste Højttaler Manualer

BOGASING M5 Manual

16 Juni 2025

Sony BRAVIA Theatre Sub 7 Manual

16 Juni 2025

Sogo SS-8395 Manual

15 Juni 2025

Gembird SPK-BT-LED-08S Manual

15 Juni 2025

Teufel Rockster NEO Manual

15 Juni 2025

Rebeltec Stage 180 Manual

15 Juni 2025

Diamond Audio DES69C Manual

15 Juni 2025

Defender Enjoy S1000 Manual

15 Juni 2025

Diamond Audio DMD652 Manual

15 Juni 2025

Rebeltec Rodos Manual

15 Juni 2025