Star Micronics BSC10II-UE Manual

Star Micronics Printer BSC10II-UE

Læs gratis den danske manual til Star Micronics BSC10II-UE (2 sider) i kategorien Printer. Denne vejledning er vurderet som hjælpsom af 11 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 6 anmeldelser. Har du et spørgsmål om Star Micronics BSC10II-UE, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

For the owners of other companies’ trademarks mentioned in this document, see Trademarks in our website (https://www.star-m.jp/eng/trademarks.html).

Pull the end of the paper out straight



and push down both sides of the printer

cover to close



Insert a paper roll in the direction shown in

the illustration



To change the paper width, the memory

switch must be set. Refer to the online

manual for details.

ⓘ

When using a paper roll with 58 mm

width, install the supplied paper roll

guide into the printer.

Hook your ngers into the cover open

groove on both sides of the printer cover



and open the printer cover



Inserting a Paper Roll

Star Windows Software

ⓘ

The Windows driver is included in the Star Windows Software. The Star

Windows Software can be used to configure the printer settings and

perform an operation test.



Download [ Star Windows Software ].



Extract the downloaded software and execute "Setup.exe".



Follow the wizard instructions and complete software installa-

tion.

Windows

Star Quick Setup Utility

ⓘ

For a wired LAN connection, use the tablet that is connected to the

same network as the BSC10II.





Once a static IP address is assigned, IP address changes through the DHCP server will not occur, so the specified connection destination device can be

used continuously once set.



Install [ Star Quick Setup Utility ].



Open the conguration utility, and select [ Start Guide (Initial

Settings)] - [Search Printer].



Follow the instructions of the utility to connect and set up a

tablet.

Android/iOS

Preparing/Setting Up the Conguration App

Conguration app

download site

ⓘ

Driver download site for Mac / Linux environment (https://www.star-m.jp/supportsite-wsw.html)

Use the conguration app to set up the printer from a tablet or PC. Scan the QR code on the right side or

search the app to access the download site.

ⓘ

The following app can be used in Standard mode. When using in a dierent mode, download the appropriate

software from the online manual.

The mode setting status can be checked from [Operation Mode] in the list that is printed at a self-printing.

For details about the self-printing procedure, refer to the online manual.

Turning on the Main Unit

Power

Turn on the power to the printer



, and

check the blue LED lights up



Connecting a Tablet or PC

Prepare a cable according to the terminal that you will use.

When using a commercially available cable, perform thorough operation verication

in advance.

Connect the cable to the connector on the printer.

USB-C

USB cable *

PC: C to A or C to C

Communication

Plug for the printer

Android

USB-A

Windows

USB-CLAN

USB-A

USB cable *

Android: A to C

Communication and Recharge

Plug for the printer

Cable that conforms to USB2.0 standards, supports

current of 1.5A or higher.

Cable that conforms to USB2.0 standards.

Cable that is compatible with category 5 or higher.

Wired LAN

LAN cable *

Communication

Plug for the printer

ⓘ

DHCP is enabled by default for the wired LAN settings.

To continually use the same IP address, set a static IP address before use. For the static

IP address setting procedure, refer to the Online Manual.

Connect the included power cable to the

inlet on the back side of the printer



Connect the plug of the power cable to the

outlet



What's Included

BSC10II online manual

This document explains the setup procedures for the BSC10II.

For further instructions, please refer to the BSC10II online manual.

Please read the instructions before using the printer.

Introduction

If contents are missing or damaged, please contact the reseller that sold you the printer.

Accessories vary depending on the region where the printer was purchased.

Attached to the paper roll guide.

BSC10II-UE

Paper Roll GuidePower Cable *

Rubber Feet *

User’s Manual Sheet

T hi s sh e e t

User's Manual Sheet

BSC10II

80870830

Produkt Specifikationer

Mærke:	Star Micronics
Kategori:	Printer
Model:	BSC10II-UE

Har du brug for hjælp?

Hvis du har brug for hjælp til Star Micronics BSC10II-UE stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Printer Star Micronics Manualer

Star Micronics TSP143IIU ECO Manual

29 August 2025

Star Micronics TSP100IV SK Manual

29 August 2025

Star Micronics BSC10II-U Manual

28 August 2025

Star Micronics DP8340 Manual

28 August 2025

Star Micronics mC-Label2 Manual

12 August 2025

Star Micronics TUP900 Manual

15 Juni 2025

Star Micronics TSP100IV Manual

5 September 2024

Star Micronics BSC10II-UE Manual

5 September 2024

Star Micronics SP700 Manual

21 August 2024

Star Micronics TSP1000 Manual

16 August 2024

Printer Manualer

Nyeste Printer Manualer

Dascom Tally 2610+ Manual

5 December 2025

Avision AP233QN Manual

5 December 2025

CUSTOM P3X Manual

5 December 2025

OKI MicroLine 5590eco Manual

5 December 2025

Avision AM233QW Manual

5 December 2025

Avision AM240AW Plus Manual

5 December 2025

Avision AM3321w Manual

4 December 2025

Avision AM4021w Manual

4 December 2025

Avision AM4332iw Pro Manual

4 December 2025

CUSTOM Q3X Manual

4 December 2025