Star Micronics TSP100IV SK Manual

Star Micronics Printer TSP100IV SK

Læs gratis den danske manual til Star Micronics TSP100IV SK (2 sider) i kategorien Printer. Denne vejledning er vurderet som hjælpsom af 10 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 5.5 anmeldelser. Har du et spørgsmål om Star Micronics TSP100IV SK, eller vil du spørge andre brugere om produktet?

Side 1/2
Copyright 2023 Star Micronics Co., Ltd.
For the owners of other companies’ trademarks mentioned in this document,see Trademarks in our website (https://www.star-m.jp/eng/trademarks.html).
Easy Setup
Guide
Safety
Instructions
Rubber
Feet
GuideUSB CablePower Cable* LAN CableTSP143IV-UE SK
This Sheet
If contents are missing or damaged, please contact the reseller that sold you the printer.
*accessories vary depending on the region where the printer was purchased.
What's Included
FAQ
TSP100IV SK online manual
This document explains the setup procedure for the
TSP100IV SK. For further instructions, please refer to the
TSP100IV SK online manual. Please read the instructions
before using the printer. You can also see FAQ from the
QR code on the inside of the printer.
Introduction
Easy Setup Guide
TSP100IV SK
80878950
1
Connecting a Tablet or PC
Connect an appropriate cable to the connector on the printer according to your
operating environment.
USB-A
   
Android
You will need: USB cable included with the printer.
1
Plug for the printer
USB-C
®
    
Windows, Mac, Linux
You will need: USB cable included with the printer.
2
3
Wired LAN
You will need:
LAN cable included with the printer.
Android
USB-A
Windows
USB-CLAN
3
12
ⓘ
When using a USB cable that is available commercially or that came with a
smartphone or tablet, perform thorough operation verification.
3
4
5
5
4
3
1
2
Star Windows Software
When using Windows
Star Quick Setup Utility
When using Android iOS/
Once a static IP address is assigned, IP address changes through the DHCP server will not occur, so the specied connection destination
device can be used continuously once set.
● For 58 mm paper width
(Gray x 1)
Install the roll paper guide
Paper Setup
Online Manual
- Use Accessories
A (LEFT) B (RIGHT)
4
Preparing/setting up the conguration app
Use the conguration app to set up the printer from a tablet or PC.
Scan the QR code on the right side or search the app to access the download site.
Conguration app
download site
Install [ Star Quick Setup Utility ].
Open the conguration utility, and select [ Start Guide (Initial
Settings)] - [ Search Printer].
Follow the instructions of the utility to connect and set up a tablet.
ⓘ
For a wired LAN connection, use the tablet that is connected to
the same network as the TSP100IV SK.
The Windows driver is included in the Star Windows Software.
The Star Windows Software can be used to configure the printer
settings and perform an operation test.
Download [ Star Windows Software ].
Extract the downloaded software and execute “Setup.exe”.
Follow the wizard instructions and complete software installation.
Driver download site for Mac / Linux environment. (https://www.star-m.jp/supportsite-wsw.html)
3
Turning on the Main Unit Power
Connect the included power cable to the inlet
on the back side of the printer
.
Connect the plug of the power cable to the
outlet
.
Turn on the power to the printer
, and check
the blue LED lights up
.
1
2
Push the opening lever
and
then open the printer cover
.
Insert a paper roll in the direction
shown in the illustration
.
Pull the end of the paper out
straight
.
Push down both sides of the
printer cover to close
.
2
Inserting a Paper Roll
When using a 58mm or 40mm width paper roll, install the supplied paper guide into the printer.
To change the paper width, the memory switch must be set. Refer to the online manual for details.
Label Builder
and more
[
Convenient Function
]
Sign up for Star Micronics Cloud Services
Service site
Registration
site
ⓘ
Please refer to the above Service site for available countries.
FREE services are available if you register TSP100IV SK with Star Micronics
Cloud Services.

Connect the printer to the internet.
(See “Wired LAN” in Step “Connect a cable”)1

Scan the QR code from a smartphone or tablet to access the registration site
for “Star Micronics Cloud Services”.
Follow the procedures to register the printer with “Star Micronics Cloud
Services” to start using the services.
● For 40 mm paper width
(Light Gray x 2)
Communication and Recharge
Communication
Communication
Plug for the printer
Plug for the printer
80 mm
58 mm
40 mm


Produkt Specifikationer

Mærke: Star Micronics
Kategori: Printer
Model: TSP100IV SK

Har du brug for hjælp?

Hvis du har brug for hjælp til Star Micronics TSP100IV SK stil et spørgsmål nedenfor, og andre brugere vil svare dig