StarTech.com RJ45SPLITTER Manual

StarTech.com Kabler til pc'er og periferiudstyr RJ45SPLITTER

Læs gratis den danske manual til StarTech.com RJ45SPLITTER (2 sider) i kategorien Kabler til pc'er og periferiudstyr. Denne vejledning er vurderet som hjælpsom af 26 personer og har en gennemsnitlig bedømmelse på 3.6 stjerner ud af 13.5 anmeldelser. Har du et spørgsmål om StarTech.com RJ45SPLITTER, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Quick-Start Guide

To view manuals, FAQs, videos, drivers, downloads, technical drawings, and more, visit www.startech.com/support.

Manual Revision: May 25, 2020 4:41 PM

Product Diagram (RJ45SPLITTER)

Component Function

1RJ45 Connector • Connect the to an existing Cable Adapter

Network.

2RJ45 Ports • Allows you to connect up to 2 Network Devices

to an existing .Network

Requirements

For the latest requirements, please visit www.startech.com/RJ45SPLITTER

• Network Devices x 2 (max 2)

• CAT5 Cables x 2

• Existing Network

Installing the Cable Adapter

1. Connect the on the to an RJ45 port on a RJ45 Connector Cable Adapter Network

Device (Ethernet Patch Panel, Wall Outlet, etc.).

Note: The on the combines the signals of 2 connections CAT5 Cable Cable Adapter

over the one .CAT5 Cable

2. Connect a to the on the and the other side to an CAT5 Cable RJ45 Port Cable Adapter

RJ45 port on a .Network Device

3. Repeat step 2 to connect a second to the .Network Device Cable Adapter

2-to-1 RJ45 Splitter Cable Adapter - F/M

Connectivity Diagram

The lays out the following scenario:Connectivity Diagram

Scenario: A company has two oces (A and B). A single CAT5 Ethernet drop connects

Oce B to the network. The company wants to put a network printer and wireless

access point in Oce B. They would like to have a dedicated Ethernet connection for

each device back to the Network Switch in Oce A.

Solution: Cable Adapters By using the two one at each location, the company can

combine two connections to the switch over the existing wiring at Oce A and split

the signal back into two connections at Oce B.

FCC Compliance Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC

Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not

occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be

determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the

following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including

interference that may cause undesired operation. Changes or modications not expressly approved by StarTech.com could void

the user’s authority to operate the equipment.

Industry Canada Statement

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe [B] est conforme à la norme NMB-003 du Canada.

CAN ICES-3 (B)/NMB-3(B)

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:

(1) This device may not cause interference, and (2) This device must accept any interference, including interference that may

cause undesired operation of the device.

Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation

est autorisée aux deux conditions suivantes:

(1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi,

même si le brouillage est susceptible d’en compromettre le fonctionnement.

Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols

This manual may make reference to trademarks, registered trademarks, and other protected names and/or symbols of third-

party companies not related in any way to StarTech.com. Where they occur these references are for illustrative purposes only

and do not represent an endorsement of a product or service by StarTech.com, or an endorsement of the product(s) to which

this manual applies by the third-party company in question. StarTech.com hereby acknowledges that all trademarks, registered

trademarks, service marks, and other protected names and/or symbols contained in this manual and related documents are the

property of their respective holders.

PHILLIPS® is a registered trademark of Phillips Screw Company in the United States or other countries.

Warranty Information

This product is backed by a three-year warranty.

For further information on product warranty terms and conditions, please refer to .

www.startech.com/warranty

Limitation of Liability

In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their ocers, directors, employees or agents)

for any damages (whether direct or indirect, special, punitive, incidental, consequential, or otherwise), loss of prots, loss of

business, or any pecuniary loss, arising out of or related to the use of the product exceed the actual price paid for the product.

Some states do not allow the exclusion or limitation of incidental or consequential damages. If such laws apply, the limitations

or exclusions contained in this statement may not apply to you.

Safety Measures

• If product has an exposed circuit board, do not touch the product under power.

Mesures de sécurité

• Si l’un des circuits imprimés du produit est visible, ne pas touchez le produit lorsqu’il est sous tension.

安全対策

•  製品に露出した状態の回路基盤が含まれる場合、電源が入っている状態で製品に触らないでください。

Misure di sicurezza

• Se il prodotto ha un circuito stampato visibile, non toccare il prodotto quando è acceso.

Säkerhetsåtgärder

• Rör aldrig vid enheter med oskyddade kretskort när strömmen är påslagen.

FR: startech.com/fr

DE: startech.com/de

ES: startech.com/es

NL: startech.com/nl

IT: startech.com/it

JP: startech.com/jp

StarTech.com Ltd.

45 Artisans Cres

London, Ontario

N5V 5E9

Canada

StarTech.com Ltd.

Unit B, Pinnacle 15

Gowerton Rd,

Brackmills

Northampton

NN4 7BW

United Kingdom

StarTech.com LLP

2500 Creekside

Parkwy

Lockbourne, Ohio

43137

U.S.A.

Produkt Specifikationer

Mærke:	StarTech.com
Kategori:	Kabler til pc'er og periferiudstyr
Model:	RJ45SPLITTER
Vægt:	45 g
Produktfarve:	Grå
Pakkevægt:	30 g
Pakkedybde:	220 mm
Pakkebredde:	200 mm
Pakkehøjde:	30 mm
Certificering:	RoHS
Kabelteknologi:	10/100Base-T(X)
Kabellængde:	0.33 m
Plug and play:	Ja
RJ-45 indgangs-porte:	1
Stik køn:	Hanstik/Hunstik
RJ-45 udgangs-porte:	2
Standard for kabler:	Cat5e
Kabel kappemateriale:	Polyvinylchlorid (PVC)