Studer XTH 8000-48 Manual

Studer Batterioplader XTH 8000-48

Læs gratis den danske manual til Studer XTH 8000-48 (1 sider) i kategorien Batterioplader. Denne vejledning er vurderet som hjælpsom af 68 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 34.5 anmeldelser. Har du et spørgsmål om Studer XTH 8000-48, eller vil du spørge andre brugere om produktet?

Side 1/1
Xtender
XTH
Data may change without any notice
* Adjustable with the RCC-02/-03
** These features are valid only when using the cooling module ECF-01.
(1)
With -01 at the end of the reference, means 120V/60Hz. Available for all Xtenders except XTH 8000-48
Model
Inverter
Nominal battery voltage 12 Vdc 24 Vdc 48 Vdc
Input voltage range 9.5 - 17 Vdc 19 - 34 Vdc 38 - 68 Vdc
Continuous power @ 2C 2500 VA 4500 VA 5000 VA 7000 VA
Power 30 min. @ 25°C 3000 VA 5000 VA 6000 VA 8000 VA
Power 5 sec. @ 2C 7.5 kVA 12 kVA 15 kVA 21 kVA
Maximum load Up to short-circuit
Asymmetric load Up to Pcont.
* Load detection (stand-by) 2 to 25 W
Cos j
0.1-1
Maximum efciency 93 % 94 % 96 %
Consumption OFF/Stand-by/ON 1.2 W / 1.4 W / 14 W 1.4 W / 1.8 W / 18 W 1.8 W / 2.2 W / 22 W 1.8 W / 2.4 W / 30 W
* Output voltage Pure sine wave 230 Vac (± 2 %) / 120 Vac
(1)
* Output frequency Adjustable 45 - 60 Hz
(1)
± 0.05 % (crystal controlled)
Harmonic distortion < 2 %
Overload and short-circuit protection Automatic disconnection with 3 time restart attempt
Overheat protection Warning before shut-off - with automatic restart
Battery charger
* Charge Characteristic
6 steps: Bulk, Absorption, Floating, Equalization, reduced oating, periodic absorption
Number of steps, thresholds, end current and times completely adjustable with the RCC-02/-03
* Maximum charging current 160 A 140 A 100 A 120 A
* Temperature compensation With BTS-01 or BSP 500/1200
Power Factor Correction (PFC) EN 61000-3-2
General data
* Input voltage range 150 to 265 Vac / 50 to 140 Vac
(1)
Input frequency 45 to 65 Hz
Input current max. (transfer relay) / Output current max.
50 Aac / 56 Aac 50 Aac / 80 Aac
Transfer time < 15 ms
Multifunction contacts 2 independent contacts (potential free 3 points, 16 Aac / 5 Adc)
Weight 34 kg 40 kg 42 kg 46 kg
Dimensions h/w/l [mm] 230 / 300 / 500 230 / 300 / 500 230 / 300 / 500
Protection index IP20
EU declaration of conformity
Low Voltage Directive (LVD) 2014/35/EU:
- EN 50178:1997
Electromagnetic Compliance (EMC) Directive 2014/30/EU:
- EN 62040-2:2006, EN 61000-3-2:2014, EN 61000-3-12:2011
Operating temperature range -20 to 5C
Relative humidity in operation 95 % without condensation
Ventilation Forced from 55°C
Acoustic level <40 dB / <45 dB (without/with ventilation)
Warranty 5 years
ISO Certication 9001:2008 / 14001:2004
Accessories
Remote control RCC-02 or RCC-03
llll
Module Xcom-232i
llll
Communication sets Xcom-LAN /w Xcom-GSM / Xcom-SMS
llll
Battery Status Processor BSP
llll
Remote Control Module RCM-10 (3 m)
2 aux. contacts module ARM-02
Cooling Module ECF-01
Battery temp. sensor BTS-01 (3 m)
llll
Communication cable for 3ph and // CAB-RJ45-8-2
llll
Mounting frame X-Connect
llll


Produkt Specifikationer

Mærke: Studer
Kategori: Batterioplader
Model: XTH 8000-48

Har du brug for hjælp?

Hvis du har brug for hjælp til Studer XTH 8000-48 stil et spørgsmål nedenfor, og andre brugere vil svare dig