Supermicro A+ Server 2024US-TRT Manual

Supermicro Server A+ Server 2024US-TRT

Læs gratis den danske manual til Supermicro A+ Server 2024US-TRT (1 sider) i kategorien Server. Denne vejledning er vurderet som hjælpsom af 12 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 6.5 anmeldelser. Har du et spørgsmål om Supermicro A+ Server 2024US-TRT, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/1

11 10 9

http://www.supermicro.com MNL-2315-QRG Rev. 1.0a

SuperServer AS -2024US-TRT Quick Reference Guide

Front View & Interface Rear View

Hard Drive Installation

Board Layout

Remov aing

Hot-Swap Drive Carrier from the

Chassis

1. Press the release button on the drive carrier, which will extend the

drive carrier handle.

2. Use the drive carrier handle to pull the drive out of the chassis.

Insta a Drivelling

1. Remove the dummy drive, by removing the screws securing the dummy drive to

the carrier. These screws are not used to mount the actual hard drive.

2. Insert a drive into the carrier with the PCB side facing down and the connector

end toward the rear of the carrier. Align the drive in the carrier so that the screw

holes line up.

3. Secure the drive to the carrier with four M3 screws, included in the chassis

accessory box.

4. Insert the drive carrier with the disk drive into its bay, keeping the carrier oriented

so that the release button is on the right side. When the carrier reaches the rear of

the bay, the release handle retracts.

5. Push the handle in until it clicks into its locked position.

Caution

SAFETY INFORMATION

IMPORTANT: See installation instructions and safety warning before

connecting system to power supply.

http://www.supermicro.com/about/policies/safety_information.cfm

WARNING:

To reduce risk of electric shock/damage to equipment, disconnect power

from server by disconnecting all power cords from electrical outlets.

If any CPU socket empty, install protective plastic CPU cap.

WARNING:

Always be sure all power supplies for this system have the same power

output. If mixed power supplies are installed, the system will not operate.

For more information go to : http://www.supermicro.com/support



1. Removing the Processor Force Frame

Use a Torx T20 driver to loosen the screws holding

down Force Frame in the sequence of . The 3-2-1

screw are numbered on the Force Frame next t each s o

screw hole.

2. Raising the Force Frame 3. Lifting the Rail Frame

5. Inserting the Carrier Frame/CPU Package 6. Lowering the Force Frame 7. Securing the Force Frame

Secure the screws in the order 1-2-3, tightening to

16.1 kgf-cm (14 lbf-in) of torque. The Force Frame

secures both the Rail Frame and CPU Package.

Caution: Tightening must be executed in proper

1-2-3 sequence to avoid causing catastrophic

damage to the socket or CPU Package.

8. The Force Frame Secured

Screw #1

Screw #2

Screw #3

Force Frame

Rail Frame

PnP Cover Cap

Carrier Frame/

CPU Package

Processor Installation

4. Removing the External Cap and PnP

Cover Cap

External Cap

PnP Cover Cap

Heatsink Installation

DescriptionNo.

PCI-E p1-x16 Slot (FH, 9.5” L)

PCI-E p1-x16 Slot (FH, 10.5” L)

VGA Port

UID LED

Serial Port

Dedicated LAN for IPMI

Two USB 3.0 Ports

Two 10G RJ45 Ports (Ultra Riser Card)

PCI-E p1-x16 Slot (LP)

10 PCI-E p1-x8 in p1-x16 Slot (FH, 10.5” L)

11 PCI-E p1-x16 Slot (FH, 10.5” L)

*Redundancy based on configuration and application load

Memory

DIMM Module Population Sequence

When installing memory modules, the DIMM slots should be populated in the following order:

DIMMA2, DIMMB2, DIMMC2, DIMMD2, DIMME2, DIMMF2, DIMMG2, DIMMH2, then DIMMA1,

DIMMB1, DIMMC1, DIMMD1, DIMME1, DIMMF1, DIMMG1, DIMMH1.

• The blue slots must be populated first.

• Always use DDR4 DIMM modules of the same type, size and speed.

• d DIMM s n be st d. er, l DI s Mixe speed ca in alle Howev al MM wil rul n a the d ot spee f stthe eslow DIMM.

• The motherboard will support odd-numbered modules (1 or 3 modules installed).

However, to achieve the best memory performance, fully populate the motherboard with validated

memory modules.

* Opt nal NVMeio Support (HDD0 a 1 from CPU1, a 3 from CPU2)nd HDD2 nd

HDD2

HDD1

HDD0

HDD5

HDD4

HDD3

HDD8

HDD7

HDD6

HDD11

HDD10

HDD9

RESET

Dummy Drive

Hard Drive Carrier

DESIGNED IN USA

H12DSU-iN

REV:

1 2

4 5

11 12 13 14 15 16

No. t nDescrip io

1SXB1 1 : -L s S t P PCI-E 4.0 )A/ B/1C WIO Ri er Card uppor (C U2 x32

2SXB2: S t P PCI-E 4.0 x )WIO-R Riser Card uppor (C U2 16

3SXB3 3 : t S t P PCI-E 4.0 )A/ B/3C Ul ra I/O Riser Card uppor (C U1 x40

4CPU1 NV 0- S A 7Me Ports 1, AT 0-

5S AAT DOM 3.0 98-

6CPU2 NV S A 3Me Port 0, AT 10-1

7CPU2 VNM e Port 1, S AAT 14-17

8CPU1 NV 3Me Ports 2-

9CPU2 NV 3Me Ports 2-

10 JBT1 - CMOS Clear

11 CPU2 DI A S tsMM 1-D2 lo

12 CPU2

13 CPU2 DI E otsMM 1-H2 Sl

14 CPU1 DI A S tsMM 1-D2 lo

15 CPU1

16 CPU1 DI E S tsMM 1-H2 lo

Pro o a Their Co o M escess rs nd rresponding Mem ry odul

CPU# Cha el nn

1Cha el nn

2Cha el nn

3Cha el nn

4Cha el nn

5Cha el nn

6Cha el nn

7Cha el nn

8 DI SMM

CPU1 C2 D2 G2 H2

CPU2 C2 D2 G2 H2

16 MM DI S

CPU1 A2 B2 C2 D2 E2 F2 G2 H2

CPU2 A2 B2 C2 D2 E2 F2 G2 H2

32 MM DI S

CPU1 A1 A2 B1 B2 C1 C2 D1 D2 E1 E2 F1 F2 G1 G2 H1 H2

CPU2 A1 A2 B1 B2 C1 C2 D1 D2 E1 E2 F1 F2 G1 G2 H1 H2

JL1

JF1

FAN7

FAN8JF2

P2-DIMMA1

P2-DIMMB1

P2-DIMMA2

P2-DIMMC1

P2-DIMMB2

P2-DIMMD2

P2-DIMMD1

P2-DIMMC2

JVR1

FAN3

FAN4

FAN5

FAN6

P2-DIMMH2

P2-DIMMG2

P2-DIMMH1

P2-DIMMF2

P2-DIMMG1

P2-DIMME2

P2-DIMMF1

P2-DIMME1

P1-DIMMD2

P1-DIMMC2

P1-DIMMC1

P1-DIMMD1

P1-DIMMA1

P1-DIMMA2

P1-DIMMB1

P1-DIMMB2

CPU1CPU2

P1-DIMMG1

P1-DIMMG2

P1-DIMMH1

P1-DIMMF2

P1-DIMMF1

P1-DIMME2

P1-DIMME1

P1-DIMMH2 FAN1

FAN2

LE1

CPU Installation

Hard Drive Signal

Hard Drive Fail

Power Button

Reset Button

NIC1 LED

Information LED

Power LED

NIC2 LED

DescriptionNo.

HDD Activity LED

Power Fail LED

745

12 1

Default Cable Routing

C or on onnect

Bo dar Card/ C n onn ioect

Backplane HDD Ba MC Ca y S bl P/e N

JSLIM1

(M -H12D U-iNB S ) CN1 CN 0- L-, 2 7 CB SAST-1253-100

JSLI 2M3-

(M -H12D U-iNB S ) CN 8-3 11 CB TL-SAS -1269 -10F 0

JSLIM2

(M -H12D U-iNB S ) NV 1Me 0-1

(Hybrid wi th S A)AT CB TL-SAS -1247-85

JSLIM4

(M -H12D U-iNB S ) NV 2Me 2-3

(Hybrid wi th S A)AT CB TL-SAS -1245-85

Redundant Power Supply Modules*

Removing a Drive Carrier

Release Button

1. Mounting the Heatsink 2. curing the HeatsinkSe

Using a diagonal pattern and a Torx T20 driver,

tighten the four heatsink screws evenly to 16.1

kgf-cm (14.0 lbf-in) torque.

#4 cre S w

#2 cre S w

#1 cre S w

#3 cre S w

Produkt Specifikationer

Mærke:	Supermicro
Kategori:	Server
Model:	A+ Server 2024US-TRT

Har du brug for hjælp?

Hvis du har brug for hjælp til Supermicro A+ Server 2024US-TRT stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Server Supermicro Manualer

Supermicro SuperServer 6028TR-HTR Manual

30 Januar 2025

Supermicro SuperServer 6019U-TR4 Manual

30 Januar 2025

Supermicro SBA-4119S-T2N Manual

11 Januar 2025

Supermicro A+ Server 1024US-TNR Manual

11 Januar 2025

Supermicro SuperServer 2028U-TNRT+ Manual

11 Januar 2025

Supermicro SuperServer 2028TR-HTFR Manual

8 Januar 2025

Supermicro SuperBlade SBI-4129P-C2N Manual

28 December 2024

Supermicro SuperServer F619P2-RC1 Manual

28 December 2024

Supermicro SuperServer E300-9A-4C Manual

28 December 2024

Supermicro SuperServer 5029AP-TN2 Manual

28 December 2024

Server Manualer

Nyeste Server Manualer

15 Juni 2025

7 Juni 2025

1 Juni 2025

9 Marts 2025

9 Marts 2025

9 Marts 2025

23 Januar 2025

23 Januar 2025

23 Januar 2025

23 Januar 2025