Supermicro SuperStorage 2029P-E1CR48H Manual

Supermicro Ikke kategoriseret SuperStorage 2029P-E1CR48H

Læs gratis den danske manual til Supermicro SuperStorage 2029P-E1CR48H (10 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 13 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 7 anmeldelser. Har du et spørgsmål om Supermicro SuperStorage 2029P-E1CR48H, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/10

Information for Lot 9 of ErP (Ecodesign)

This addendum addresses European Union (EU) Ecodesign requirements for servers and storage

products. All data and ratings within this addendum are in reference only to the Supermicro product(s) in

the manual. The below information conforms requirements laid down in Annex II of the Commission to

Regulation 2019/424.

3(1)(a): See Section 1.1 of the system manual for the product type.

3(1)(b): See the title page and preface of the system manual for the trademark and

manufacturer’s address.

3(1)(c): See the title page of the system manual for product model number(s).

3(1)(d): See the serial number on the physical system to determine the year of manufacture.

3(1)(e-j): PSU Efficiency and Power Factor Value (Table) (From 80 Plus report)

PSU Model #:PWS-1K62A- 1R

Watts: 1620

PSU Efficiency

Power Fact or

% Rated Load of

10 %

20 %

50 %

100 %

50 %

Single Output (AC-DC)

87.6 %

91.9 %

94.0 %

91.4%

0.98

System (EUT) Efficiency in Idle State Power (Table)

Representative

Configurations

Measured Idle State

Power (W)

Calculated Idle Power

Allowance (W)

High-End Performance

Configuration

312.90

679.56

Typical Configuration

N/A

Low-End Performance

Configuration

186.70

335.16

System (EUT) Efficiency in Active State Power (Table)

Representative

Configurations

Active State

Efficiency Score

(Effserver)

Minimum Active State

Efficiency for 2-Socket

Server

High-End Performance

Configuration

27.3

Typical Configuration

N/A

9.5

Low-End Performance

Configuration

18.6

3(1)(k): The operating condition class is A2.

Dry bulb temp °C

Hum idity range, non-condensing

Operating

condition

class

Allowable

range

Recom

mend ed

range

Allowable range

Recommended range

Max dew

point (°C )

Maximum

rate of

change (°

C/hr)

15 32-

18 27-

–

12 °C Dew Point (DP) and

8 % relative humidity (RH) to

17 °C DP and 80 % RH

–

9 °C DP to

15 °C and DP

60 % RH

5/20

10 35-

18 27-

–

12 C °DP and 8 % RH to

21 C and % °DP 80 RH

Same as A1

5/20

5-40

18 27-

–

12 C °DP and 8 % RH to

24 C and % °DP 85 RH

Same as A1

5/20

5-45

18 27-

–

12 C °DP and 8 % RH to

24 C and % °DP 90 RH

Same as A1

5/20

3(1)(l): The idle state power at the higher boundary temperature of the operating conditions

class is 369 W.

3(1)(m): The active state efficiency and performance is SERT Score = .327 (High End

Configuration)

3(1)(n): There are two methods by which a user can securely delete data from this system. The

user performing secure data deletion should be an IT professional.

The first is with a Unified Extensible Firmware Interface (UEFI) shell utility. This utility

works on X10/X11/H11/H12/M11 motherboard series with onboard SATA/NVMe devices.

Any user may access and download this utility through following link:

https://www.supermicro.com/about/policies/disclaimer.cfm?url=/wftp/utility/Lot9_Secure

_Data_Deletion_Utility/

Download the shell utility package and extract it to a USB flash drive, then plug the drive

into the server for which secure data deletion is necessary. Then turn the system on.

Navigate to the BIOS setup menu, then place the server system into the UEFI shell

environment. Follow the instructions in the README file to invoke the utility and

complete the deletion.

The second method is through the secure data deletion tool provided by the original

manufacturer of the hard drive. This should be used in a scenario where the shell utility

is not applicable. Each manufacturer should have the tool available on their website. If

needed, please look on the hard drive label for the name of the manufacturer and model

information.

3(1)(o): List of recommended combinations of blade servers with chassis: N/A.

3(1)(p): List of all current SKUs within this product family: -E1CR48H, 2029P-E1CR48L. 2029P

3(3)(a): There is no use of cobalt in batteries in this product.

Produkt Specifikationer

Mærke:	Supermicro
Kategori:	Ikke kategoriseret
Model:	SuperStorage 2029P-E1CR48H

Har du brug for hjælp?

Hvis du har brug for hjælp til Supermicro SuperStorage 2029P-E1CR48H stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Supermicro Manualer

Supermicro X11SWN-E Manual

6 Juni 2025

Supermicro X14SAE Manual

31 Marts 2025

Supermicro H8DGT-HF Manual

23 Februar 2025

Supermicro H8SGL Manual

23 Februar 2025

Supermicro X14DBI Manual

30 Januar 2025

Supermicro X14SAZ-F Manual

30 Januar 2025

Supermicro X10SLE-HF Manual

13 Januar 2025

Supermicro X10SLE-DF Manual

13 Januar 2025

Supermicro X10SLD-HF Manual

13 Januar 2025

Supermicro X10SLE-F Manual

8 Januar 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

AmpliVox Airvox SW695 Manual

15 Juni 2025

Stiga SBC 635 KD Manual

15 Juni 2025

Cleveland 36CGM300 Manual

15 Juni 2025

Gourmia GTF7970 Manual

15 Juni 2025

Planet Audio P9630B Manual

15 Juni 2025

ORNO OR-DOM-YR-934UD Manual

15 Juni 2025

Lavex 842CD12VST12 Manual

15 Juni 2025

Marshall RCP-PLUS Manual

15 Juni 2025

Hughes & Kettner BassForce XL Manual

15 Juni 2025

Hughes & Kettner Red Box Mk III Manual

15 Juni 2025