System Sensor SPRL Manual

System Sensor Højttaler SPRL

Læs gratis den danske manual til System Sensor SPRL (4 sider) i kategorien Højttaler. Denne vejledning er vurderet som hjælpsom af 50 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 25.5 anmeldelser. Har du et spørgsmål om System Sensor SPRL, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

1 I56-0001-001

01-12

For use with the following models:

Wall Speakers: SPRL, SPWL

Ceiling Speakers: SPCRL, SPCWL

PRODUCT SPECIFICATIONS

Standard Operating Temperature: 32°F to 120°F (0°C to 49°C)

Humidity Range: 10 to 93% Non-condensing

Nominal Voltage: 25 Volts or 70.7 Volts

Maximum Supervisory Voltage: 50 VDC

Speaker Frequency Range: 400 – 4000 Hz

Power Settings: ¼, ½, 1, 2 Watts

Input terminal wire gauge: 12 to 18 AWG

PRODUCT DIMENSIONS MOUNTING BOX OPTIONS

WALL PRODUCTS Length Width Depth SPEAKERS

Wall Speaker 6.520" (165 mm) 5.00" (127 mm) 0.97" (24.6 mm) 4" x 4" x 2

or deeper

CEILING PRODUCTS Length Width Depth

Ceiling Speaker 6.8" (173 mm) N/A 1.00" (25.4mm)

NOTICE: This manual shall be left with the owner/user of this equipment.

BEFORE INSTALLING

Please read the System Sensor Voice Evacuation Application Guide, which

provides detailed information on speaker notification devices, wiring and

special applications. Copies of this manual are available from System Sensor.

NFPA 72 and NEMA guidelines should be observed.

Important: The notification appliance used must be tested and maintained

following NFPA 72 requirements.

GENERAL DESCRIPTION

System Sensor series of notification appliances offer a wide range of audible

and visible devices for life safety notification. Our line of speakers is designed

to be used at either 25 or 70.7 volts, and operate at any one of four input

power levels. Our speakers are suitable for dry and damp environments.

These products are electrically backwards compatible with previous genera-

tion of System Sensor speakers. With its low total harmonic distortion, the

System Sensor SPL series offers high fidelity sound output. Wall and ceiling

products may be used interchangeably (wall products may be used on ceiling

and ceiling product may be used on wall).

The speakers, and all power level settings, are listed to ANSI/UL 1480 require-

ments for public mode applications.

FIRE ALARM SYSTEM CONSIDERATIONS

All wiring must be installed in compliance with the National Electrical Code

(NEC) and applicable local codes. System Sensor recommends installing fire

alarm speakers in compliance with NFPA 72, ANSI/UL 1480 and NEC 760.

WIRING AND MOUNTING

All wiring must be installed in compliance with the National Electric Code

and the local codes as well as the authority having jurisdiction. Wiring must

not be of such length or wire size which would cause the notification appli-

ance to operate outside of its published specifications. Improper connections

can prevent the system from alerting occupants in the event of an emergency.

Wire sizes up to 12 AWG (2.5 mm²) may be used with the mounting plate. The

mounting plate ships with the terminals set for 12 AWG wiring.

Make wire connections by stripping about

" of insulation from the end of

the wire. Then slide the bare end of the wire under the appropriate clamping

plate and tighten the clamping plate screw.

See Figure 1 for wiring terminals and strip guide reference.

1. Connect the speaker as shown in Figure 1.

2. There are two rotary switches on the back of the product. The first switch

is used to select either 25 or 70.7 volts input and the second switch is used to

select the input power of ¼, ½, 1 or 2 watts. (See Figure 2.)

FIGURE 1. WIRING DIAGRAM AND WIRING TERMINALS

(-)

(+)

(-)

(+)

Input from

Amplifier

Output to

Next Device or EOL

A0380-00

Wiring Terminals

1. Negative (-). Line in and out

2. Positive (+). Line in and out

3. Positive (+). Line in and out

NOTE: Do not loop electrical wiring

under terminal screws. Wires

connecting the device to the control

panel must be broken at the device

terminal connection in order to

maintain electrical supervision.

FIGURE 2. SPEAKER WATTAGE AND VOLTAGE SETTINGS

A0419-01

INSTALLATION AND MAINTENANCE INSTRUCTIONS

3825 Ohio Avenue, St. Charles, Illinois 60174

800/736-7672, FAX: 630/377-6495

www.systemsensor.com

I56-0001-001

Dual Voltage Speakers

for Fire and ECS/MNS Systems

– Wall and Ceiling Mount

Produkt Specifikationer

Mærke:	System Sensor
Kategori:	Højttaler
Model:	SPRL

Har du brug for hjælp?

Hvis du har brug for hjælp til System Sensor SPRL stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Højttaler System Sensor Manualer

System Sensor SPRK Manual

13 August 2024

System Sensor SPCWK-R Manual

12 August 2024

System Sensor SPR Manual

10 August 2024

System Sensor SPWL Manual

9 August 2024

System Sensor SPRL Manual

6 August 2024

Højttaler Manualer

Nyeste Højttaler Manualer

LG XBOOM Go DXG8T Manual

7 Januar 2026

LG XBOOM 360 XO2T Manual

7 Januar 2026

Dynaudio Acoustics M1 MkII Manual

7 Januar 2026

Dynaudio Acoustics M2 MkII Manual

7 Januar 2026

Kenwood eXcelon XM77 Manual

6 Januar 2026

Thomson RT400DABBT Manual

5 Januar 2026

Kenwood eXcelon XM77TWL Manual

4 Januar 2026

Kenwood eXcelon XM65WL Manual

4 Januar 2026

Kenwood eXcelon XM65TWL Manual

4 Januar 2026

Karma BM 541 Manual

4 Januar 2026