Tanita D-1000PLUS Manual

Tanita Ikke kategoriseret D-1000PLUS

Læs gratis den danske manual til Tanita D-1000PLUS (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 48 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 24.5 anmeldelser. Har du et spørgsmål om Tanita D-1000PLUS, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

D10007921(0)

You will receive readings only if data has been programmed into the Tanita Remote Display.

For questions or help with product: Call Customer Service (847) 640 - 9241 (US & Canada Only)

Do not use the body fat reading feature of this product if you have a pacemaker or other electronic

implanted medical device. The body fat monitor function is not intended for pregnant women,

professional athlete or bodybuilders.

WARNING

1) Before proceeding, a) Install the batteries in the platform.

b) Install the batteries and set the clock in the remote display.

c) The platform and the remote display are within 17 feet (5 m) of each other.

2. Pairing the remote display and Tanita wireless platform (”platform”)

The platform needs to pair with the applicable remote display before measurements are attempted.

2) Press and hold the OFF button for 2 seconds on the remote display.

The remote display will show “ 1234 ” for selecting a personal number.

Select the preferred personal number which will be paired with the platform

using ▲/▼buttons and press the SET button to confirm.

3) The remote display will show “ SEt-P ”. Select “ YES ” or “ no ”

using ▲/▼ buttons, and press the SET button to confirm,

4) Input the 5 digit serial number found on the bottom of the

platform using ▲/▼buttons and press the SET button to

confirm.

Note: ・ “ 00000 ”, “ 000001 ” and more than “ 65535 ”.

These serial numbers are not allowed. Please input the correct serial number.

・ The serial number is located on the bottom of the platform.

Cancellation-1: Press the OFF button to cancel during the pairing process and then the clock will be displayed.

Cancellation-2: The pairing process will be cancelled if inactive for 1 minute and then the clock will be displayed.

1) Set Hour

Press ▲/▼buttons to set hour and then press SET.

The unit will beep once to confirm.

2) Set Minute

Press ▲/▼buttons to set minute and then press SET.

The unit will beep twice to confirm the programming.

• Resetting Clock

Press the clock button on the bottom of the remote display.

Then follow the clock setting procedure 1) and 2).

1. Initial Setting (Clock Setting)

Insert batteries into the remote display and then press

any front panel button to set the clock.

a) “ YES ”: The pairing process will continue to the next step.

b) “ no ”: The pairing process will be cancelled and then

the clock will be displayed.

Note:

To confirm the paired serial number on each personal number after completion the

pairing process:

Press and hold the SET button for 2 seconds on the remote display. The remote display will show “ -1- ”.

Select the personal number using ▲/▼buttons, and press the SET button to confirm. The display shows

the paired serial number for 3 seconds.

“- - - - -” is shown if there is no serial number stored for the selected personal number.

5) Once the pairing process is completed with the platform, the remote

display shows “ donE ” and then the clock will be displayed. If the remote

display shows “ P-Err ”, please try the pairing process again.

1) Selal Data Number

Use the SET button to activate the unit. Use ▲/▼buttons to select a personal data number.

Press the SET button.

You will receive readings only if data has been programmed into the Tanita remote display.

2) Set Age (Applicable Age: Refer to the platform manual)

Use ▲/▼buttons to select age. Press the SET button.

3) Select Female or Male (Athlete mode: Refer to the platform manual)

Use ▲/▼buttons to select Female / Male / Athlete Female / Athlete Male. Press the SET button.

4) Specify Height

Use ▲/▼buttons to select height. Press the SET button to confirm.

3. Setting and storing personal data in the remote display

The remote display will beep twice and the display will flash all data three times to confirm the programming.

The power will then shut down automatically.

To use the DCI (Daily Calorie Intake) feature properly, you need to set the Activity Level.

Level 1 = Inactive lifestyles (little or no exercise)

Level 2 = Moderately active lifestyles (occasional, low intensity exercise)

Level 3 = Adult involved in intense physical activity

Note: If you select the Athlete Mode, it will automatically set the Activity Level to Level 3.

Use the ▲/▼ buttons to specify Activity Level. Press the SET button to confirm.

5) Select Activity Level

Please review the Tanita wireless platform instruction manual for remote display operations, warnings, and other

important information. The instruction manual of each platform also includes the following procedures.

- Taking body composition readings

- Programming The Guest Mode - Taking Weight Measurement Only

- Recall Function

Battery Cover

Backlight Button

Upright Position

Note: If there is no serial number on the bottom of the

platform, the pairing process is not required and

you can skip to the section 3, settting and storing

personal data in the remote display.

Note: D-1000plus only, but it also depends on the platform specification, refer to platform manual.

Serial Number Sticker

Serial No.

X X X X X

Produkt Specifikationer

Mærke:	Tanita
Kategori:	Ikke kategoriseret
Model:	D-1000PLUS

Har du brug for hjælp?

Hvis du har brug for hjælp til Tanita D-1000PLUS stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Tanita Manualer

Tanita FitScan UM-041F Manual

2 August 2024

Tanita Style Leader SR-901 Manual

31 Juli 2024

Tanita 1479J2 Manual

4 Marts 2024

Tanita CalorieJump Manual

11 November 2023

Tanita WBGT Heat Index Meter TT-563 Manual

5 Maj 2023

Tanita D-1000PLUS Manual

14 April 2023

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

OmniMount POWER40 Manual

17 Juni 2025

OmniMount OL50FT Manual

17 Juni 2025

Intermatic FD30MHW Manual

17 Juni 2025

Toorx SRX-EVOLVE Manual

17 Juni 2025

OmniMount WorldMount 2N1-L Manual

17 Juni 2025

OmniMount WorldMount 4N1-L Manual

17 Juni 2025

Intermatic FD60MC Manual

17 Juni 2025

Microchip MPFS160TLS Manual

17 Juni 2025

Hughes & Kettner Metal Master Manual

17 Juni 2025

Hansgrohe AXOR Montreux 16516310 Manual

17 Juni 2025