Techno Line WS 9251 Manual

Techno Line Vejrstation WS 9251

Læs gratis den danske manual til Techno Line WS 9251 (6 sider) i kategorien Vejrstation. Denne vejledning er vurderet som hjælpsom af 39 personer og har en gennemsnitlig bedømmelse på 4.1 stjerner ud af 20 anmeldelser. Har du et spørgsmål om Techno Line WS 9251, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/6
Please read the instructions carefully and keep the manual well for future reference.
1. Remove the battery door of the main unit and transmitter.
2. Install 2 new AA size batteries for both main unit and transmitter, according to the polarity mark on
the battery compartment.
3. Replace the battery door.
4. After the batteries are installed, all LCD segment will be shown.
5. Press the “RESET” key of main unit first, and press the “RESET” key of transmitter.
6. It will automatically receive 433 MHz signal from transmitter for channel test in 8 seconds.
7. After 5 minutes channel test, it will turn to RC signal reception automatically.
8. Radio Controlled function, the current time & date automatically synchronized with the time signal
transmitted from Germany(DCF77).
1. The unit can operate up to 3 remote transmitters.
2. Position the unit and transmitter within the effect transmission range: 50 meters in usual ive
circumstances.
3. In some cases, you may not receive the signal immediately, you can reset the unit and transmitter
again as described above.
1. LCD display
- Display of the time, alarm time, outdoor & indoor temperature and weather forecast.
2. SNOOZE / LIGHT key
- Press it to turn on backlight for 5 seconds.
- When the alarm is sounding, press it to stop the current alarm and activate snooze.
3. ALARM SET key
- Press it to display alarm time for 5 seconds. During alarm time displayed, press it to turn on/ off alarm
function.
- Press and hold it for 3 seconds to enter alarm setting mode.
- In alarm setting mode, press it to step the setting item, and press it to save and exit the setting.
4. CH/+ key
- In normal mode, press it to select channel 1 to channel 3.
- Press and hold it for 3 seconds to turn to channel auto-change mode. Press it again to return to
normal mode.
- In setting mode, press it to adjust the value of the flashing digit upwards. And press it without
releasing to speed up the setting.
5. MEM/- key
- In normal mode, press it to check the max./min. indoor and outdoor temperature record for 5 seconds.
- Press and hold it for 3 seconds to delete the max./min. temperature record.
- In setting mode, press it to adjust the value of the flashing digit downwards. And press it without
releasing to speed up the setting.
6. DISPLAY SET key
- In normal mode, press and hold it for 3 seconds to enter time setting mode.
- In time setting mode, press it to step the setting item, and press and hold it for 3 seconds to save and
exit the setting.
7. °C/°F slide switch
- Select temperature unit between °C/°F.
8. SENSOR key
- Press it to start 433 MHz channel test for main unit & transmitter.
- During the channel test, press and hold it for 3 seconds to manual turn off.
9. RCC key
- Press it to manual receive RC signal.
- During the RC reception, press and hold it for 3 seconds to turn off synchronisation.
10. RESET key
- In case of mal-function, press it by using a metal wire to reset all the values.
11. Battery door
1. LED indicator
- Flashes when the remote unit transmitting a reading.
2. CHANNEL slide switch
- Assign the transmitter to Channel 1, 2 or 3.
3. RESET key
- Press it to reset the transmitter.
4. Wall-mounting holder
- Use it to support the transmitter on the wall.
5. Battery compartment
The signal indicator flashing means time signals are being received. If the RC weather station receives
signal successfully, a sync-time symbol “ ” appears on the LCD. The unit has already received the
time signal. Otherwise, the signal strength symbol will disappear from the LCD display.
You may press “RCC” key to receive the time signal manually. The receive mode will be off
automatically after 6-16 minutes. Receive mode consumes more battery power that may reduce
battery lifetime.
The weather station has been programmed to automatically switch when daylight saving time is in
effect. Your clock will display “DST” on the LCD during the summer.
If the weather station does not receive the time signal successfully, you can set the time manually. As
soon as the transmitter is received again, the weather station will automatically synchronize with the
received time.

Produkt Specifikationer

Mærke: Techno Line
Kategori: Vejrstation
Model: WS 9251

Har du brug for hjælp?

Hvis du har brug for hjælp til Techno Line WS 9251 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Vejrstation Techno Line Manualer

Techno Line

Techno Line WS 9130 Manual

3 August 2025
Techno Line

Techno Line WS 9215 Manual

3 August 2025
Techno Line

Techno Line WS 9490 Manual

2 August 2025
Techno Line

Techno Line WS 9750 Manual

2 August 2025
Techno Line

Techno Line MA 10860 Manual

2 August 2025
Techno Line

Techno Line WS 6441 Manual

2 August 2025
Techno Line

Techno Line WS 9136 Manual

2 August 2025
Techno Line

Techno Line WS 9910 Manual

1 August 2025
Techno Line

Techno Line WS 6832 Manual

1 August 2025
Techno Line

Techno Line WL1025 Manual

1 August 2025

Vejrstation Manualer

Nyeste Vejrstation Manualer

Hyundai

Hyundai WS 2303 Manual

10 August 2025
TFA

TFA 30.3039 Manual

8 August 2025
TFA

TFA Linea Plus 35.1144.01 Manual

7 August 2025
TFA

TFA 98.1111.02 Manual

7 August 2025
TFA

TFA 30.3900.02 Manual

7 August 2025
TFA

TFA View 35.1142 Manual

7 August 2025
Brandson

Brandson 307346 Manual

5 August 2025
Theben

Theben LUXORliving M140 Manual

3 August 2025
Theben

Theben Meteodata 140 S Manual

3 August 2025
Theben

Theben LUXORliving M130 Manual

2 August 2025