Theben CHEOPS drive KNX Manual

Theben Termostat CHEOPS drive KNX

Læs gratis den danske manual til Theben CHEOPS drive KNX (2 sider) i kategorien Termostat. Denne vejledning er vurderet som hjælpsom af 11 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 6 anmeldelser. Har du et spørgsmål om Theben CHEOPS drive KNX, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

310486

CHEOPS drive KNX

Electromotor-driven, proportional actuator 7319200

3. Description of the device

The motor-driven actuator with the stroke display receives set commands

from a room temperature regulator.

Closing cover

Access in open state

to program button and

unlocking of actuator

Display of valve

opening, for

example 20 %

Note:

The valve is opened as

following depending on which

LED is lit up.

9. Display of the valve setting

Valve opening in %:

81 .. 100 %

61 ... 80 %

41 ... 60 %

21 ... 40 %

1 ... 20 %

0 % = no LED

1. Close the cover to secure access to

interlock of the actuator and to secure

the programming button.

2. Turn the enclosed special key, rotate

the interlock by 90°.

10. Protection against unauthorized removal

11. Technical data

12. Service

1. Usage

The electro-motor-driven proportional (constant) actuator is suitable for connection

to the European Installation Bus KNX. The connection is made directly without any

separate bus coupler. The power supply comes from the KNX.

2. Safety

Installation and assembly of electrical equipment must only be performed by appro-

priately trained electricians. National requirements and safety regulations must be

observed. The regulations and instructions conforming to the manual of the ZVEI/

ZVEH for building system technology must be observed for proper laying of bus lines

and placing the KNX devices in service! Tampering with or making changes to the

machine will cause render any claims under the warrantee null and void.

4. Assembly/disassembly

Assembly:

1. Select the adapter ring that fits from those included with delivery.

2. Tighten the adapter ring (Fig. ). Finger-tight is sufficient.1

3. Open the cover of the actuator.

4. Bring the device into the vertical assembly position, Fig. 2.

5. Push the device onto the adapter ring until you can hear it snap into place.

Disassembly:

1. Open the cover of the actuator.

2. Press on the red lever, see Fig. , to the left.3

3. Remove the actuator.

5. Bus connection

7. Entering the physical address

1. Apply the bus voltage. While the automatic adjustment run is in progress, one

of the three lower LEDs flashes.

Note:

The adjustment process may last as long as 10 minutes.

Once the automatic adjustment is finished, only the 4th LED from the top lights up.

If no application is loaded:

The actuator is opened to 25 % (the 4th LED from the top lights up).

8. Adjusting the automatic valve

Only ETS can be used to assign the physical address and

group addresses, and to adjust parameters

Loading the physical address/ application:

1. Press the key . LED is lit.1 2

2. Now ETS can be used to load first the physical

address and then the application.

The connection cable can be brought to

a desired mounting location in one of the

cable ducts.

1. Push the cable into the cable duct

that has been prepared on the rear

side of the device.

2. Note the polarity.

3. + –Connect the bus cable to the bus line (red / black )

Note: The two free connection cables can be used as binary inputs for

window contacts and/or presence indicators, for example.

Fig. 1Fig. 2Fig. 3

6. Connection to the window contact and/or presence indicator

yellow/ green: E1

Window Window

---- ----

---- ---- ---- ----

Presence

white/ brown: E2 Bus voltage KNX: 29 V DC

Current consumption KNX bus < 12 mA

Operating temperature: 0 °C ...+ 50 °C

Run time: < 20 s/mm

Set force: max. 120 N

Detection of valve limit stops: Automatic

Adapter rings included will fit: Danfoss RA, Heimeier, MNG, Schlösser from

3/93, Honeywell, Braukmann, Dumser (distri-

butor), Reich (distributor), Landis + Gyr,

Oventrop, Herb, Onda

Type of device: 1 according to EN 60730-1

Protection class: III

Protection type: IP 21 (EN 60529)

Pollution degree: 2

Rated impulse voltage: 330 V

Theben AG

Hohenbergstr. 32

72401 Haigerloch

GERMANY

Tel. +49 7474 692-0

Fax +49 7474 692-150

Service

Tel. +49 7474 692-369

Fax +49 7474 692-207

hotline@theben.de

Addresses, telephone numbers etc. at

www.theben.de

2 1

Cheops drive_310 486_GB_Cheops_drive_GB - 310 080 30.01.14 16:56 Seite 1

Produkt Specifikationer

Mærke:	Theben
Kategori:	Termostat
Model:	CHEOPS drive KNX

Har du brug for hjælp?

Hvis du har brug for hjælp til Theben CHEOPS drive KNX stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Termostat Theben Manualer

Theben RAMSES 850 top3 OT Manual

3 August 2025

Theben RAM 811 Top - 811 9 901 Manual

5 Oktober 2024

Theben RAM 797 HF Manual

1 Oktober 2024

Theben RAMSES 366-1 top2 Manual

23 September 2024

Theben Ramses 784 S Manual

22 September 2024

Theben RAM 801 top Manual

18 September 2024

Theben RAM 797 HF set 4 Manual

15 September 2024

Theben RAMSES 725 Thermostaat Manual

15 September 2024

Theben RAMSES 798 Thermostaat Manual

15 September 2024

Theben RAMSES 707 Thermostaat Manual

15 September 2024

Termostat Manualer

Nyeste Termostat Manualer

Vimar 09474 Manual

25 December 2025

Fantini Cosmi EC18RL Manual

18 December 2025

Fantini Cosmi L23EM1B Manual

17 December 2025

Fantini Cosmi Intellicomfort CH141AK Manual

16 December 2025

Fantini Cosmi Intellicomfort CH141E Manual

16 December 2025

Essentials MATRIX Manual

2 December 2025

Honeywell CT62B Manual

1 December 2025

Honeywell X2P RTH20B Manual

28 November 2025

Honeywell RTH2CWF Manual

27 November 2025

Honeywell CT60A1036 Manual

27 November 2025