T.I.P. SINUS 5/1 S0 Manual

T.I.P. Energimåler SINUS 5/1 S0

Læs gratis den danske manual til T.I.P. SINUS 5/1 S0 (2 sider) i kategorien Energimåler. Denne vejledning er vurderet som hjælpsom af 29 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 15 anmeldelser. Har du et spørgsmål om T.I.P. SINUS 5/1 S0, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

L1↑: incoming line conductor L1 of the circuit

L1↓: outgoing line conductor L1 to load

L2↑: incoming line conductor L2 of the circuit

L2↓: outgoing line conductor L2 to load

L3↑: incoming line conductor L3 of the circuit

L3↓: outgoing line conductor L3 to load

N: neutral conductor of the circuit

N: (neutral conductor of the circuit)

Quick installation Guide

for SINUS Energy Meters

SINUS 85 S0 / M-Bus / Modbus

Installation notes for SINUS Energy Meters

Always take note of the specications on

the type label!

For an energy meter with the voltage specications

3x230/400V on type label please note the following values:

Reference voltage Un = 3x230/400V

(3-phase four-wire alternating current system)

For an energy meter with the current specications 0,25-5(85)

A on type label please note the following values:

Initial current Ist

= 0,02 A

Minimal current Imin = 0,25 A

Suppressed

leakage current Itr = 0,5 A

Reference current Iref = 5 A

Maximal current Imax = 85 A

with symmetrically loaded phases.

Always follow the specications for the measurement

operating requirements on the type label.

As pre-fuse please install only in the measurement voltage

circuits fuses with max. 80 A.

The used wires have to be chosen regarding to current

density and installation requirements, so that the conductors

at all time don’t heat up to more than +55°C closer than 20cm

tot he energy meter. The load capacity of wires and cables is

dened in DIN VDE 0298- 4.

The size of the curre -, voltage- and neutral terminals is for nt

min 2,5 mm² and max 25 mm².

For the screws use a screwdriver type SL for slotted screws

with a size of 5,5mm x 1,0mm. The M5 terminal-screws

should be tightened with a torque of 2,5 Nm.

The size of the additional terminals is for min 0,25 mm² and

max 1,5 mm².

For the screws use a screwdriver type SL for slottet screws

with a size of 3,5mm x 0,6mm. The M5 terminal-screws

should be tightened with a torque of 0,4 Nm.

Wires with splitted core should end in a wire termination. The

torques for screws at clamping units are dened in DIN EN

60999 1.-

Further important information for use af this device are in the

manual (delivered with the device).

TIP Thüringer Industrie Produkte GmbH

Bahnhofstraße 26 D- 842 Ruhla –99

Tel.: +49 36929 64029 0 Fax: +49 36929 64029 29 –

www.stromzaehler.de

CT K1: incoming line conductor L1 of the circuit

CT L1: outgoing line conductor L1 to load

CT k1: CT output S1/k conductor L1

CT l1: CT output S2/l conductor L1

CT K2: incoming line conductor L2 of the circuit

CT L2: outgoing line conductor L2 to load

CT k2: CT output S1/k conductor L2

CT l2: CT output S2/l conductor L2

CT K3: incoming line conductor L3 of the circuit

CT L3: outgoing line conductor L3 to load

CT k3: CT output S1/k conductor L3

CT l3: CT output S2/l conductor L3

Meter k1: to CT-output S1/k conductor L1

Meter l1: to CT-output S2/l conductor L1

Meter k2: -output S1/k conductor L2 to CT

Meter l2: to CT-output S2/l conductor L2

Meter k3: to CT-output S1/k conductor L3

Meter l3: to CT-output S2/l conductor L3

Meter L1: Measurement voltage input (L1)

Meter L2: Measurement voltage input (L2)

Meter L3: Measurement voltage input (L3)

Meter neutral conductor of the circuit N:

Meter (neutral conductor of the circuit) N:

Quick installation Guide

for SINUS Energy Meters

SINUS 5//1 S0 / M-Bus / Modbus

Installation notes for SINUS Energy Meters

Always take note of the specications on

the type label!

For an energy meter with the voltage specications

3x230/400V on type label please note the following values:

Reference voltage Un = 3x230/400V

(3-phase four-wire alternating current system)

For an energy meter with the current specications 0,01-1(6)

A on type label please note the following values:

Initial current Ist

= 0,002 A

Minimal current Imin = 0,01 A

Suppressed

leakage current Itr = 05 A 0,

Reference current Iref = 1 A

Maximal current Imax = 6 A

with symmetrically loaded phases.

Always follow the specications for the measurement

operating requirements on the type label.

As pre-fuse please install only in the measurement voltage

circuits fuses with max. 6 A.

The secondary circuits oft he current transformers may not be

fuses.

The cable cross-section and the sort of voltage lines tot he

energy meter have to be chosen regarding to the place, pre-

fuses and installed length between the meter and voltage

source and if necessary regional valid regulations. The load

capacity of wires and cables is dened in DIN VDE 0298- 4.

The selection of the cable cross-sections of the current line

has to regard to the secondary CT nominal current, apparent

power, over current range of the CTs, the length of the cable

between meter and voltage source and if necessary regional

valid regulations.

The size of the current-, voltage- and neutral terminals is for

min 0,5 mm² and max 6 mm².

For the screws use a screwdriver type SL for slottet screws

with a size of 4,0mm x 0,6mm. The M5 terminal-screws

should be tightened with a torque of 0,5 Nm.

The size of the additional terminals is for min 0,25 mm² and

max 1,5 mm².

For the screws use a screwdriver type SL for slotted screws

with a size of 3,5mm x 0,6mm. The M5 terminal-screws

should be tightened with a torque of 0,4 N m.

Wires with splitted core should end in a wire termination. The

torques for screws at clamping units are dened in DIN EN

60999 1.-

Further important information for use af this device are in the

manual (delivered with the device).

TIP Thüringer Industrie Produkte GmbH

Bahnhofstraße 26 D-99842 Ruhla –

Tel.: +49 36929 64029 0 Fax: +49 36929 64029 29 –

www.stromzaehler.de

Produkt Specifikationer

Mærke:	T.I.P.
Kategori:	Energimåler
Model:	SINUS 5/1 S0

Har du brug for hjælp?

Hvis du har brug for hjælp til T.I.P. SINUS 5/1 S0 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Energimåler T.I.P. Manualer

T.I.P. SINUS 5/1 S0 Manual

4 September 2024

T.I.P. SINUS 85 S0 Manual

4 September 2024

Energimåler Manualer

Nyeste Energimåler Manualer

Schneider PowerLogic METSEION7410 Manual

25 September 2024

Schneider PowerLogic METSEION7403 Manual

25 September 2024

Schneider EasyLogic PM2230 Manual

25 September 2024

Schneider PowerLogic METSEION7413 Manual

25 September 2024

Voltcraft SEM6000 app Manual

26 August 2024

PROmax PM-300 POWER METER Manual

25 August 2024

Go Green gsm 00812 Manual

25 August 2024

Xavax 111908 Premium Manual

23 August 2024

Kostal Smart Energy Meter Manual

22 August 2024

Hama 108834 Manual

21 August 2024