PROmax PM-300 POWER METER Manual

PROmax Energimåler PM-300 POWER METER

Læs gratis den danske manual til PROmax PM-300 POWER METER (1 sider) i kategorien Energimåler. Denne vejledning er vurderet som hjælpsom af 63 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 32 anmeldelser. Har du et spørgsmål om PROmax PM-300 POWER METER, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/1

910 11

TOTAL

KWh

MAX

KWh

Battery

Before operating, two 1.5V (type LR-44 or AG-13) button cell

batteries (included) should be installed into the unit.

Unplug the unit from the outlet

Put the two batteries into the compartment while observing

the correct polarities as shown on the battery compartment.

Place the cover back onto the unit.

The two batteries serve to backup the readings and electricity

rate in case of power failure or when the unit is unplugged from

the outlet.

Note: If you have to leave the unit unplugged for a long period

of time (more than a month), the batteries should be

removed in order to conserve battery consumption.

About the PM300

PM300 is a power meter that allows you measure the energy

consumption of electrical appliance, and by entering the

electricity rate, to calculate the total cost of an appliance's power

consumption. It also detects the overload condition and usage

information. To fully utilize the function of the power meter,

please read the rest of the manual.

Quick User Guide

MEASUREMENT

!Press A(UP) key to select Voltage , Amp, Max AMP, Watt ,

Max Watt and Overload Display

!Press B(DOWN) key to select KWh, Total Cost and Price

SET PRICE

!Press B(DOWN) key to select Price display Mode

!Press D(PRICE SET) key to enter Price Setting Mode

!Use A(UP) or B(DOWN) key to adjust price and press

D(PRICE SET) key to confirm

SET OVERLOAD WARNING

!Press A (UP) key to select Overload Display Mode

!Press C (Overload Set) key to enter Overload Setting Mode

!Press A(UP) or B(DOWN) key to select desired W or A

!Press C (Overload Set) key to enter to Value Setting Mode

!Use A(UP) or B(DOWN) to adjust to desired value of Over

Load Watt or Amp and press C(OVERLOAD SET) key to

confirm

CLEAR MAX LOAD

!Press and hold A (UP) & C(OVERLOAD SET) key for 3

seconds to clear the Max Load readings and buzzer beep

CLEAR USAGE READING

!Press and hold B (DOWN) & D(PRICE SET) key for 3

seconds to clear "usage time " and "KWh" reading , buzzer

beep

Fig.5

Fig.6

Fig.7

Fig.8

MAX

KWh

6. Overload setting Mode

In this mode, "OVERLOAD" symbol is lighted ON. The

default setting of "overload wattage" is 0 W. Press

OVERLOAD key, the symbol "W" flash means "overload

wattage" is selected. Press UP or DOWN key to toggle

between "W" and "A". Flash "A" means "overload current" is

selected. Press OVERLOAD key again, the first digit

flash,use UP key or DOWN key to set the desired value of

the first digit. Press OVERLOAD key to select next digit,

and so on.

Press and hold the UP key and OVERLOAD together for about

3 seconds, all MAX reading will be clear to zero.

MID PANE

Press the "DOWN KEY" key to view each of the following 3

mode's status. All of these information are displayed on the

middle pane.

4. Wattage Mode

In this mode, real power (in Watt). The calculation of the

power consumed by the load, in watt, is resulted from

multiplying the voltage, current and power factor (power =

voltage x current x power factor). The resolution of power

consumed is 1 watt. Press UP key will go to MAX. Wattage

mode.

5. MAX. Wattage Mode

In this mode, the maximum wattage is displayed. This

reading will be held until another higher reading is captured

and save as the new Max. Wattage.

1. Volt Mode

Line voltage (in V) is displayed on the top pane. Press UP

key will go to Current Mode.

2. Current Mode

In this mode, present current (in A) drawn by the load is

displayed. Press UP key will go to MAX. Current mode.

3. MAX. Current Mode

In this mode, the maximum current is displayed.This reading

will be held until another higher reading is captured and

save as the new Max. current.

Current

Mode

Max

Current

Mode

Wattage

Mode

Max

Watt

Mode

Overload

Setting

Line

Voltage

Mode

Fig.1

Fig.3

Fig.4

Fig.2

Total

energy

KWH

Total

Cost

Price

per

KWH

Total

energy

KWH

PM-300 POWER METER

USER MANUAL

LCD Display

1. KWh Mode

This mode displays the total accumulated energy used by

the appliance (in KWh) from the start of measurement. The

resolution is 0.01 KWh and the maximum is 9999.99KWh.

Press DOWN key will go to Total Cost mode.

2. Total Cost mode

The accumulative energy cost used by the load is

calculated. When the cost is over $999.999, there will be no

decimal place, so the total cost can be shown up to

$999999. The total cost is based on the price set in

Price/KWh mode.

Press DOWN key go to Price/ KWh mode.

3. Price/ KWh mode

In this mode the price per KWh is displayed and set. The

rate set here will affect "cost of the energy used".

LCD

Display

Panel

UP Key Battery

Cover

Down Key

Overload Set

Price Set

Socket

Line

Voltage

Mode

MAX

KWh

TOTAL

PRICE/KWh

Produkt Specifikationer

Mærke:	PROmax
Kategori:	Energimåler
Model:	PM-300 POWER METER

Har du brug for hjælp?

Hvis du har brug for hjælp til PROmax PM-300 POWER METER stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Energimåler PROmax Manualer

PROmax PM-300 POWER METER Manual

25 August 2024

Energimåler Manualer

Nyeste Energimåler Manualer

Schneider PowerLogic METSEION7410 Manual

25 September 2024

Schneider PowerLogic METSEION7403 Manual

25 September 2024

Schneider EasyLogic PM2230 Manual

25 September 2024

Schneider PowerLogic METSEION7413 Manual

25 September 2024

T.I.P. SINUS 5/1 S0 Manual

4 September 2024

T.I.P. SINUS 85 S0 Manual

4 September 2024

Voltcraft SEM6000 app Manual

26 August 2024

Go Green gsm 00812 Manual

25 August 2024

Xavax 111908 Premium Manual

23 August 2024

Kostal Smart Energy Meter Manual

22 August 2024