TP-Link TL-SF1006P Manual


Læs gratis den danske manual til TP-Link TL-SF1006P (3 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 9 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 5 anmeldelser. Har du et spørgsmål om TP-Link TL-SF1006P, eller vil du spørge andre brugere om produktet?

Side 1/3
Connection
© 2020 TP-Link 7106508699 REV1.0.0
Installation Guide
6-Port 10/100Mbps Desktop Switch with 4-Port PoE+
LED Explanation
Power
On: Power on
O: Power o
Note: 1. PoE ports can also connect to non-PoE devices, but only transmit data.
2. TL-SF1006P can supply up to 30 W for each PoE port and 67 W for all PoE ports.
Power
PoE MAX
PoE Max
On: 60 W≤Total power supply < 67 W
Flashing: Total power supply ≥ 67 W
O: Total power supply < 60 W
DC Power Adapter
AC Power Cord
Router
LAN Port WAN Port
Internet
Ethernet Ports (1-6)
PoE Ports (1-4)
IP Camera IP Phone
PoE Devices
AP
Link/Act and PoE Status
On: Link present but no activity
Flashing: Transmitting/receiving data
O: No link
On: Providing PoE power
Flashing: Current-overload/Short-circuit
O: Not providing PoE power
O: Port 1–4 run at 10/100 Mbps and support PoE power supply up to 100 m
away.
On: Port 1–4 run at 10 Mbps and support PoE power supply up to 250 m away.
Extend (Port 1–4)
O: All the ports transmit data in the same priority.
On: Port 1 and 2 transmit data in a higher priority than other ports. When
congestion occurs, packets which are transmitted by the ports with higher
priority occupy the whole bandwidth.
Priority (Port 1–2)
Switch Explanation
Network Video Recorder
Frequently Asked Questions (FAQ)
The Power LED should be lit when the power system is working normally. If the
Power LED is not lit, please try the following:
A1: Make sure the AC power cord is connected to the switch with power source
properly.
A2: Make sure the voltage of the power supply meets the requirements of the
input voltage of the switch.
A3: Make sure the power source is on.
Q1. Why is the Power LED not lit?
Please try the following:
A1: Make sure that the cable connectors are rmly plugged into the switch and
the device.
A2: Make sure the connected device is turned on and works normally.
A3: The cable must be less than 100 meters long (328 feet).
Q2. Why is the Link/Act LED not lit while a device is connected
to the corresponding port?
General Specications
Specications
Q3. Why are PoE ports not supplying power for PoE devices?
When the total power consumption of connected PoE devices exceeds the
maximum, the PoE port with a smaller port number has higher priority. The
system will cut o power to the ports with larger port numbers to ensure
supplying to other ports.
For example, if port 1, 2 and 4 are consuming 15.4 W respectively, and an
additional PoE device with 21 W is inserted to port 3, the system will cut o the
power of port 4 to compensate for the overload.
Operating Temperature
Storage Temperature
Operating Humidity
Storage Humidity
0 C to 40 C (32 F to 104˚ ˚ ˚ ˚F)
-40 C to 70 C (-40 F to 158˚ ˚ ˚ ˚F)
10% to 90%RH non-condensing
5% to 90%RH non-condensing
Environmental and Physical Specications
Продукт сертифіковано згідно с правилами системи УкрСЕПРО на відповідність вимогам
нормативних документів та вимогам, що передбачені чинними законодавчими актами
України.
Safety Information
Keep the device away from water, re, humidity or hot environments.
Do not attempt to disassemble, repair, or modify the device.
Do not use damaged charger or USB cable to charge the device.
Do not use any other chargers than those recommended.
Adapter shall be installed near the equipment and shall be easily accessible.
Place the device with its bottom surface downward.
Use only power supplies which are provided by manufacturer and in the origin packing of
this product. If you have any questions, please don’t hesitate to contact us.
TP-Link hereby declares that the device is in compliance with the essential requirements and other
relevant provisions of directives 2014/30/EU, 2014/35/EU, 2009/125/EC, 2011/65/EU and
(EU)2015/863.
The original EU declaration of conformity may be found at https://www.tp-link.com/en/ce.
EU Declaration of Conformity
PoE Disclaimer
The speed of the ports in extend mode will downgrade to 10 Mbps. The actual transmission
distance may vary due to power consumption of PoE-powered devices or the cable quality and
type.
PoE budget calculations are based on laboratory testing. Actual PoE power budget is not
guaranteed and will vary as a result of client limitations and environmental factors .
For technical support and other information, please visit
https://www.tp-link.com/support, or simply scan the QR code.
If you have any suggestions or needs on the product guides, welcome
to email techwriter@tp-link.com.cn.
To ask questions, find answers, and communicate with TP-Link users or
engineers, please visit https://community.tp-link.com to join TP-Link
Community.
Standard
Protocol
Interface
IEEE 802.3i, IEEE 802.3u, IEEE 802.3x, IEEE802.1p, IEEE
802.3af, IEEE 802.3at
CSMA/CD
6 10/100 Mbps RJ45 Ports, Auto-Negotiation MDI/MDIX
PoE Ports: Port 1-Port 4
PoE Power Budget: 67 W
Network Media (Cable)
10BASE-T: UTP category 3, 4, 5 cable (maximum 100 m);
EIA/TIA-568 100Ω STP (maximum 100 m)
100BASE-TX: UTP category 5, 5e cable (maximum 100 m);
EIA/TIA-568 100Ω STP (maximum 100 m)
Yes
94 mm
Wall Mountable
Distance Between
Mounting Holes
Switching Capacity
Power Supply
MAC Address Learning
Transfer Method
MAC Address Table
1.2 Gbps
2K
Store-and-Forward
Automatically learning, automatically aging
External Power Adapter
Input: 100-240 VAC, 50/60 Hz
Output: 53.5 VDC /1.31 A


Produkt Specifikationer

Mærke: TP-Link
Kategori: Ikke kategoriseret
Model: TL-SF1006P

Har du brug for hjælp?

Hvis du har brug for hjælp til TP-Link TL-SF1006P stil et spørgsmål nedenfor, og andre brugere vil svare dig