Tripp Lite AS400CABLEKIT2 Manual


Læs gratis den danske manual til Tripp Lite AS400CABLEKIT2 (16 sider) i kategorien Kabler til pc'er og periferiudstyr. Denne vejledning er vurderet som hjælpsom af 43 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 22 anmeldelser. Har du et spørgsmål om Tripp Lite AS400CABLEKIT2, eller vil du spørge andre brugere om produktet?

Side 1/16
Owner’s Manual
Warranty
Registration:
Register online today for a chance
to win a FREE Tripp Lite
product—www.tripplite.com/warranty
Programmable Relay I/O Card
Model: RELAYIOCARD
Copyright © 2010 Tripp Lite. All rights reserved. All trademarks are the property of their respective owners.
1111 W. 35th Street, Chicago, IL 60609 USA
www.tripplite.com
Use of this equipment in life support applications where failure of this equipment can reasonably be expected
to cause the failure of the life support equipment or to significantly affect its safety or effectiveness is not
recommended. Do not use this equipment in the presence of a flammable anesthetic mixture with air, oxygen
or nitrous oxide.
1 Introduction 2
1.1 Product Features 2
1.2 Package Contents 2
2 Installation and Setup 2
2.1 System Requirements 2
2.2 Communications Setup 2
2.3 Configuration 3
2.4 AS400 Configuration 4
3 Specifications 5
4 Warranty & Warranty Registration 5
Español 6
Français 11
201011142 932815.indb 1 1/6/2011 9:15:13 AM
2
1. Introduction
2. Installation and Setup
1.1 Product Features
The RELAYIOCARD is a programmable UPS management device featuring:
• 6 programmable relay output contacts
• Configurable normal open or normal close for each relay contact
• Configurable UPS shutdown delay time
• Configurable input signal to shutdown UPS or test battery
The RELAYIOCARD allows you to:
• Monitor UPS status and events
• Perform remote system shutdowns and battery tests
1.2 Package Contents
This Package Contains:
• RELAYIOCARD
• Configuration Cable
• Faceplates
• Owner’s Manual
2.1 System Requirements
The RELAYIOCARD supports all Tripp Lite SmartOnline™ UPS Systems and select SmartPro™ UPS Systems, including
SMART1050SLT, SMART1500SLT, SMART2200RMXL2U, SMX1050SLT, SMX1500SLT, SMART3000SLT, SMART2200SLT,
SM2200RMNAFTA, SMART2600RM2U, SMART3000RM2U, SMART1500CRMXL, SMART1500SLTXL, SMART750XLa,
SMX3000XLRT2U and SMX2200XLRT2U. Supported systems must run a UPS protocol of 3008 or above.
To determine your UPS protocol:
1. Open Tripp Lite PowerAlert software.
2. Click on the “Misc” button on the main screen of the PowerAlert console.
3. View the protocol variable.
2.2 Communications Setup
1. Connect Tx to pin 2, Rx to pin 3 and GND-C to pin 5 of RS-232 DB9 port.
2. In the Windows environment, launch the Hyper Terminal program, then open the specified COM port.
3. Set the following properties – Baud rate: 2400, Data Bits: 8, Parity: None, Stop Bit: 1, Flow Control: None.
201011142 932815.indb 2 1/6/2011 9:15:14 AM


Produkt Specifikationer

Mærke: Tripp Lite
Kategori: Kabler til pc'er og periferiudstyr
Model: AS400CABLEKIT2

Har du brug for hjælp?

Hvis du har brug for hjælp til Tripp Lite AS400CABLEKIT2 stil et spørgsmål nedenfor, og andre brugere vil svare dig