Tripp Lite PDU3XVS6G20 Manual

Tripp Lite Strømskinne PDU3XVS6G20

Læs gratis den danske manual til Tripp Lite PDU3XVS6G20 (100 sider) i kategorien Strømskinne. Denne vejledning er vurderet som hjælpsom af 13 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 7 anmeldelser. Har du et spørgsmål om Tripp Lite PDU3XVS6G20, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/100

User’s Guide

SNMPWEBCARD

Firmware Version 12.06.0062 through 12.06.0065

Revision A

Documentation Notice: This User’s Guide is a supplement to the printed manual that came with your SNMPWEBCARD or network-enabled Tripp Lite device. Refer to

the printed manual for instructions on hardware installation and basic conﬁguration, including IP address assignment. If you have misplaced your printed manual, refer

to the electronic version included on the bundled CD-ROM or download it at www.tripplite.com/support/manuals/.

WARRANTY

REGISTRATION:

chance to win a FREE Tripp Lite

product—www.tripplite.com/warranty

1. Introduction 2

1.1 System Requirements 2

2. Installation and Conﬁguration 2

2.1 Saving Conﬁguration Changes 2

2.2 Default UPS System

Shutdown Settings 2

2.3 Other Default Settings 3

2.4 SNMP Conﬁguration 3

3. Web Console 4

3.1 Opening the Web Console 4

3.1.1 Alternate to Web Launch 4

3.2 Web Console Interface 5

3.3 Device Summary 5

3.4 Status Menu 5

3.4.1 Status > Overview 5

3.4.2 Status > Details 6

3.4.3 Status > Alarms 7

3.5 Device Menu 7

3.5.1 Device > Controls 7

3.5.2 Device > Loads 8

3.5.3 Device > Load Groups 8

3.5.4 Device > Events 9

3.5.5 Device > Device Discovery 9

3.6 Actions Menu 10

3.6.1 Actions 10

3.6.1.1 Actions > Event Actions >

Device Actions 10

3.6.1.2 Actions > Event Actions >

General Actions 13

3.6.2 Actions > Scheduling 14

3.6.3 Actions > Address Book 15

3.7 Logs 15

3.7.1 Logs > Event Logs 15

3.7.2 Logs > Data 15

3.8 Preferences 16

3.8.1 Preferences > Network 16

3.8.2 Preferences > DNS 18

3.8.3 Preferences > Security 18

3.8.4 Preferences > System 22

3.8.5 Preferences > Restart 24

3.9 RSS Support 24

3.10 Help 25

4. Telnet/SSH Console 26

4.1 Device Menu 27

4.1.1 Status 28

4.1.2 Identiﬁcation 29

4.1.3 Controls 30

4.1.3.1 Control Data 31

4.1.4 Events 32

4.1.5 Loads 35

4.1.5.1 Load Conﬁguration 35

4.1.5.2 Load Groups 36

4.1.5.3 Ramp/Shed Settings 37

4.1.6 Preferences and Thresholds 38

4.1.7 Device Alarms 39

4.1.8 Logs 39

4.2 System Conﬁguration 39

4.2.1 Address Book 39

4.2.1.1 Email Contacts 40

4.2.1.2 SNMP Contacts 41

4.2.1.3 HTTP Contacts 42

4.2.2 Global Actions 43

4.2.2.1 Action Proﬁles 43

4.2.2.2 Schedules 55

4.2.3 Security 59

4.2.3.1 Authentication Method 59

4.2.3.2 Local Users 60

4.2.3.3 RADIUS Servers 63

4.2.3.4 Change Password 64

4.2.4 Date/Time 64

4.2.4.1 Time Source Data

Entry Menu 64

4.2.4.2 Time Settings 65

4.2.4.3 SNTP Settings 66

4.2.4.4 RTC Settings 66

4.2.5 Local Device Discovery 67

4.2.6 Restart PowerAlert 68

4.3 Network Conﬁguration 69

4.3.1 IP Conﬁguration 69

4.3.1.1 Host Name 70

4.3.1.2 Domain Data Entry Menu 70

4.3.1.3 IPV4 Settings 70

4.3.1.4 IPV6 Settings 71

4.3.1.5 DNS Settings 72

4.3.2 Remote Services 73

4.3.2.1 Email Settings 73

4.3.2.2 Remote Syslog 75

4.3.2.3 Watchdog Settings 78

4.3.3 User Interfaces 79

4.3.3.1 Telnet/SSH 79

4.3.3.2 Web Console 79

4.3.3.3 SNMP Settings 80

4.3.3.4 FTP 80

4.3.3.5 Remote View Access Port 80

4.4 Alarms and Logging 81

4.4.1 Alarms 81

4.4.1.1 Alarm Details 82

4.4.2 View Logs 82

4.4.2.1 Data Log 83

4.4.2.2 Event Log 85

4.4.3 Logging Settings 88

4.4.3.1 Accounting Log Settings 88

4.4.3.2 Application Log Settings 88

4.4.3.3 Data Log Settings 89

4.4.3.4 Event Log Settings 90

4.4.3.5 Format Settings 91

4.5 About 92

5. Command Line Interface 93

5.1 Syntax Conventions 93

5.2 Manual Pages 94

5.3 Output Conventions 94

5.4

Getting Started with the PowerAlert CLI

6. Troubleshooting 96

7. Technical Support 96

8. Appendix 97

Table of Contents

1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/support

SNMPWEBCARD is an optional network card that you can install in the accessory slot of a compatible UPS system, PDU* or cooling unit.

SNMPWEBCARD connects your Tripp Lite device to your Ethernet network as a manageable device that supports remote monitoring, remote control

and remote condition reporting. You can manage the device from PowerAlert Network Management System, an SNMP Network Management

Station, a Web browser or telnet. Remote access capability allows you to reboot, control outlets, shed nonessential loads, monitor load levels and

more. The SNMPWEBCARD can also send SNMP traps or email messages to the addresses you specify, alerting you automatically to events such

as power failures.

* SNMPWEBCARD is preinstalled in Tripp Lite Monitored and Switched PDUs, which can be identiﬁed by the presence of “MN” or “NET” in the model name. SNMPWECARD is also preinstalled in SRCOOLNET.

For instructions on hardware installation and basic conﬁguration, refer to the printed manual that came with your SNMPWEBCARD or Tripp Lite

device. For instructions on loading a ﬁrmware or device driver upgrade on the SNMPWEBCARD, refer to the PowerAlert software release notes. The

manual and release notes can be found on the bundled CD-ROM or downloaded from www.tripplite.com/manuals/.

2.1 Saving Conﬁguration Changes

While using PowerAlert, most of your conﬁguration changes will take effect immediately so you can try out your conﬁguration before committing to

it. The Web and Telnet Menu user interfaces will typically advise you if your conﬁguration requires a restart to take effect.

In general, the conﬁguration is not persisted permanently until you restart PowerAlert (or ‘reboot’ the SNMPWEBCARD). You should restart PowerAlert

when your conﬁguration is complete and before testing conﬁgurations that simulate or nearly simulate a power outage. For your convenience, most

changes will auto-save after about 30 minutes of idle time. Changes to the network settings will not.

Restarting PowerAlert cannot cause equipment powered through your UPS or PDU to experience an outage and has no effect on the general

operation of your Tripp Lite device.

When used with a Tripp Lite UPS, during a power failure, SNMPWEBCARD

is pre-conﬁgured to shut down the UPS system two minutes after

receiving a low battery signal. This allows the UPS system to provide

the maximum available runtime to connected equipment. If you want to

change the default setting, follow these instructions and refer to Figure

2-1 and Figure 2-2:

1. Use a Web browser to open the PowerAlert console window for your

SNMPWEBCARD (see 3.1 Opening the Web Console for instructions).

2. Click the Actions menu A and access the Event Actions submenu B.

3. Select Device Shutdown in the Device Shutdown Actions C section.

4. Click the button on the bottom of the screen D to add a new

action.

5. In the Name ﬁeld E, type a name for the new action.

• Tripp Lite UPS system, PDU, or cooling unit with compatible accessory slot or preinstalled SNMPWEBCARD.

• Ethernet network that supports the TCP/IP protocol. Firewall ports 3664 and 3665 must be open.

• One of the following options for remote monitoring and control:

• PowerAlert Network Management System

• SNMP-based Network Management Station (such as HP® OpenView®)

• Web browser that supports frames, forms and Java™ (such as Microsoft® Internet Explorer® 8.0 or later) (if launching vid browser)

• VT-100 Telnet and/or SSH Client

• For “Terminal Mode” conﬁguration only:

• Terminal emulation software program (such as TeraTerm Pro by Ayera Technologies)

• Computer with available DB9 serial port

Warning: Use of this equipment in life support applications where failure of this equipment can reasonably be expected to cause the failure of the life support equipment or to signiﬁcantly affect its

safety or effectiveness is not recommended. Do not use this equipment in the presence of a ﬂammable anesthetic mixture with air, oxygen or nitrous oxide.

1. Introduction

2. Installation and Conﬁguration

1.1 System Requirements