Tycon Systems RemotePro Manual

Tycon Systems Solpanel RemotePro

Læs gratis den danske manual til Tycon Systems RemotePro (12 sider) i kategorien Solpanel. Denne vejledning er vurderet som hjælpsom af 22 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 11.5 anmeldelser. Har du et spørgsmål om Tycon Systems RemotePro, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/12

RPST

RemotePro®

Remote Power System

▫ Wireless Base Stations

and Client Devices

▫ Surveillance Cameras

▫ Remote Sensors

▫ Remote Lighting

▫ Off Grid Electronics

Congratulations! on your purchase of the RemotePro off grid ™ -

remote power system. Please take a moment to review this Qwik

Install Guide before assembly or battery installation.

DANGER! Avoid Powerlines!

You Can Be Killed!

When following the instructions in this guide take extreme care

to avoid contact with overhead power lines, lights and power circuits.

Contact with power lines, lights or power circuits may be fatal. We rec-

ommend to install no closer than 20 feet to any power lines.

Safety: For your own protection, follow these safety rules.

▫ Perform as many functions as possible on the ground

▫ Do not attempt to install on a rainy, windy or snowy day or if

there is ice or snow accumulation at the install site or if the

site is wet.

▫ Make sure there are no people, pets, etc. below when you are

working on a roof or ladder.

Recommended Tools: Phillips Screwdriver, 13mm and 10mm

Wrench, nut driver, Flat Blade Screwdriver5/16”

Please help preserve the environment and return

used batteries to an authorized depot

Qwik Install

STEP 1: Add Grounding Wire Between Door and Enclosure: Remove

plastic covers on copper studs on

inside of door and inside of enclo-

sure. Add jumper wire between 2

copper studs and use copper wash-

ers and nuts to secure.

STEP 2: Remove the bottom cover

and replace it with the PowerVent™

included with the package. Add wire

feedthrus and any necessary con-

nectors into the bottom PowerVent™

plate.

STEP 3: Install hole plug in drain

hole in bottom right corner of the en-

closure.

STEP 4: Mount the DIN rail to the

door using screws provided. Mount

any extra equipment to the orange

backplate and secure the backplate in

the enclosure. Note: The DIN rail can

also be mounted to the orange back-

plate or sides of enclosure if desired.

STEP 5: If pole mounting the enclo-

sure, assemble the pole mount kit to

the back of the enclosure and mount

the enclosure to a pole using the 6 hose clamps provided. The enclo-

sure can also be wall mounted using the 4 holes in the back of the en-

closure.

Produkt Specifikationer

Mærke:	Tycon Systems
Kategori:	Solpanel
Model:	RemotePro

Har du brug for hjælp?

Hvis du har brug for hjælp til Tycon Systems RemotePro stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Solpanel Tycon Systems Manualer

Tycon Systems RemotePro Manual

22 August 2024

Tycon Systems RPAL48-180-1000 Manual

22 August 2024

Solpanel Manualer

Nyeste Solpanel Manualer

Mestic MSBC-250 Manual

8 Juni 2025

Mestic MSMO-140 Manual

8 Juni 2025

Mestic MSBC-110 Manual

7 Juni 2025

Mestic MSMO-100 Manual

7 Juni 2025

Mestic MSMO-180 Manual

7 Juni 2025

Mestic MSMO-120 Manual

6 Juni 2025

Mestic MSBC-300 Manual

6 Juni 2025

Mestic MSMO-200 Manual

6 Juni 2025

Mestic MSBC-220 Manual

6 Juni 2025

Mestic MSMO-160 Manual

6 Juni 2025