V-TAC VT-560 Manual


Læs gratis den danske manual til V-TAC VT-560 (27 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 16 personer og har en gennemsnitlig bedømmelse på 4.1 stjerner ud af 8.5 anmeldelser. Har du et spørgsmål om V-TAC VT-560, eller vil du spørge andre brugere om produktet?

Side 1/27
WARNING!
1. Please make sure to turn off the power before starting the installation.
2. The light source of this luminaire is not replaceable, when the light source reaches its
end of life the whole luminaire should be replaced.
2. Installation should only be done by a certified electrician.
WEEE Number: 80133970
INSTALLATION INSTRUCTION
NEON FLEX LIGHT
This marking indicates that this
product should not be disposed of
with other household wastes.
Caution, risk of electric
shock.
IN CASE OF ANY QUERY/ISSUE WITH THE PRODUCT, PLEASE REACH OUT TO US AT: SUPPORT@V-TAC.EU
FOR MORE PRODUCTS RANGE, INQUIRY PLEASE CONTACT OUR DISTRIBUTOR OR NEAREST DEALERS.
V-TAC EUROPE LTD. BULGARIA, PLOVDIV 4000, BUL.L.KARAVELOW 9B
TECHNICAL DATA:
2
YEARS
WARRANTY
*
IP65
RATING
Model Was Lumens
Beam
Angle
Body Type CRI
PCB
Width
Roll/M
LED
QTY/M
Opera on
Temperature
VT-559 13 1000 120° Silicone >80 8mm 10 120 -20 to +60°c
VT-560 8 530 120° Silicone >90 4mm 5 238 -20 to +60°c
VT-555 8 320 160° Silicone >80 5mm 10 120 -20 to +60°c
INTRODUCTION
Attention
!
vertically bending
Cutting instruction
SAFETY INSTRUCTION AND WARNINGS!
1. Please cut the LED Neon Flex according to the cutting as shown in the cutting instruc-
tions. Cutting outside the marking will damage the product. Please cut only on the
dotted/scissor marking on the LED Neon Flex. End Cap required.
2. LED Neon Flex cannot be folded, bent or twisted during the installation. Please install
in straight direction. DO NOT turn on power until LED Neon Flex is connected properly
and well-installed.
3. DO NOT touch/cut the LED Neon Flex when power is on.
4. DO NOT power the LED Neon Flex in roll/package.
5. DO NOT install in water or flammable environment, and make sure well ventilated.
6. DO NOT wrap or cover LED Neon Flex with any objects. Additional waterproof measure
needed when used outdoors.
7. DO NOT directly connect LED Neon Flex to AC power. Special power plug is needed.
8. If LED Neon Flex does not work when Power is on, please check "+" and "-" polarity.
9. When selecting power supply always add additional 10% to the maximum load.
10. DO NOT use excessive wire length between the power supply and LED Neon Flex to
avoid voltage drop
Thank you for selecting and buying V-TAC product. V-TAC will serve you the best.
Please read these instructions carefully before starting the installing and keep this
manual handy for future reference. If you have any another query, please contact
our dealer or local vendor from whom you have purchased the product. They are
trained and ready to serve you at the best. The warranty is valid for 2 years from
the date of purchase. The warranty does not apply to damage caused by incorrect
installation or abnormal wear and tear. The company gives no warranty against
damage to any surface due to incorrect removal and installation of the product.
The products are suitable for 10-12 Hours Daily operation. Usage of product for 24
Hours a day would void the warranty. This product is warranted for manufacturing
defects only.
Please cut only on the dotted/scissor marking on the LED Neon Flex.
End Cap required.
>60°


Produkt Specifikationer

Mærke: V-TAC
Kategori: Ikke kategoriseret
Model: VT-560

Har du brug for hjælp?

Hvis du har brug for hjælp til V-TAC VT-560 stil et spørgsmål nedenfor, og andre brugere vil svare dig