Vanson BC-2612T Manual

Vanson Batterioplader BC-2612T

Læs gratis den danske manual til Vanson BC-2612T (4 sider) i kategorien Batterioplader. Denne vejledning er vurderet som hjælpsom af 10 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 5.5 anmeldelser. Har du et spørgsmål om Vanson BC-2612T, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

ENGLISH

GREAT BRITAIN

For consumer contact, please visit www.clasohlson.co.uk and click on customer service.

Ver. 200811

Battery Charger

Art.no.: 18-2442 Model: BC-2612T-UK

36-3633 BC-2612T

Please read the entire instruction manual before using the product

and save it for future reference. We apologise for any text or photo-

graphic errors and any changes of technical data. If you have any

questions concerning technical problems please contact our

Customer Service Department.

1. Safety

• This charger is only intended for the charging of rechargeable

lead-acid batteries. The charging of other types of battery could

damage the charger, battery or other property.

• Battery acid is corrosive. If any acid comes into contact with

your skin or eyes: Rinse immediately with plenty of water and

immediately contact a doctor.

• The charger is not intended for use as a power supply unit.

• Only use the battery charger indoors in a well ventilated place.

Do not cover the charger.

• Never expose the charger to moisture or humidity.

• During charging the battery can emit explosive gases. It is

therefore important to avoid making sparks close to the battery.

• Wear safety glasses and turn your face away when you connect

or disconnect the battery clamps.

• Always disconnect the charger from the power supply before

cleaning it or when it is not in use.

• Never use the charger if it is damaged. Do not charge

damaged batteries.

• Do not open the casing. Certain components inside the casing

carry dangerous currents. Contact with these may cause

electric shocks.

• The charger should only be repaired by qualied service personnel.

• The charger is only short-circuit protected for a limited duration;

avoid short-circuiting the charger for longer than 1 minute,

otherwise the charger could become damaged.

• Make sure the battery is connected with the correct polarity.

• Open the battery caps (does not apply to maintenance-free

batteries) before charging.

• Check the level of the electrolyte and top up with distilled water

if necessary before beginning to charge the battery.

• The battery charger and lead-acid batteries are not toys. Do not

let children use them without supervision.

• First unplug the charger from the mains, then remove the battery

clamps from the terminals.

2. Product Description

• Automatically charges 2, 6 and 12 V lead-acid batteries.

• Switches automatically to maintenance charge when the battery

is fully charged.

• Safety feature to ensure that the connectors are not live until

they are connected to the battery in the correct way.

• Protected from short circuits and reverse polarity.

N.B. Make sure that the charger is set to the correct voltage

setting. Setting the charger incorrectly can result in damage to

the battery and/or charger.

3. Functions

• As opposed to a simpler charger, the charging current of this

charger is variable and depends on the battery’s level of charge,

condition, age, capacity and type.

• If the battery is very discharged, the charger will use a high

charging current (up to 0.6 A) at the beginning, after a while

the current will then drop whilst the voltage will increase. Large

batteries naturally take longer to charge than smaller batteries.

• The battery does not need to be completely discharged before

it is recharged; it is all right to charge a partially discharged

battery. The battery can also be connected to the charger for

maintenance charging over a long period of time.

• If the charger is short circuited or the polarity is reversed when

connected, the charger will be disconnected immediately.

It will start automatically when the cables have been properly

connected to the battery.

• The charger will make sure that the battery becomes fully

charged whilst at the same time preventing over-charging and

internal gas build-up.

• LEDs indicate charging (green) and reverse polarity or defect

battery (red).

4. Use

1. Always unplug the charger from the mains before connecting

the charger leads to the battery.

2. Before starting to charge the battery, make sure the battery is

rechargeable and has a rated voltage of 2, 6 or 12 V.

3. Set the selector switch (on the bottom of the charger) to the

correct voltage (2, 6 or 12 V) depending on the type of battery.

4. Connect the positive (RED) battery clamp to the battery’s

positive terminal (+) and the negative (BLACK) to the battery’s

negative terminal (-).

5. Plug the charger into the mains to start the charging process.

6. The LEDs on the front of the charger display the status of

the charging:

• Red: Defective battery, reversed polarity

• Green: The battery is correctly connected and charging

has commenced.

• None of the LEDs come on: The selector on the bottom of

the charger is set to the wrong voltage. Open-circuit in the

battery or leads. The battery clamps are not connected to

a battery.

5. Care and Maintenance

Always disconnect the charger from the power source before cleaning.

Use a soft, damp cloth to clean the device. Never clean the product

using strong detergents or solvents.

6. Troubleshooting

The charger does not start charging:

1. Check the terminal voltage of the battery.

2. Make sure that the selector on the bottom of the charger is set to

the same terminal voltage as the battery.

3. The battery might be faulty, test the charger with another battery.

7. Disposal

Follow local ordinances when disposing of this product.

If you are unsure how to dispose of the product, please

contact your municipality.

8. Specications

Battery charger for

lead-acid batteries

having a voltage of: 2, 6 or 12 V.

Power supply: 230 V AC, 50 Hz (Max. 22 W)

Charging current: Max. 0.6 A

Charging voltage: Normal charging: 2.3 V, 6.9 V and 13.8 V

Maintenance charging: Max. 100 mA

Recommended battery

capacity: 2 Ah – 10 Ah

Short-circuit protection: Yes, for up to 1 minute

Produkt Specifikationer

Mærke:	Vanson
Kategori:	Batterioplader
Model:	BC-2612T

Har du brug for hjælp?

Hvis du har brug for hjælp til Vanson BC-2612T stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Batterioplader Vanson Manualer

Vanson V-9688 Manual

23 August 2024

Vanson BC-2612T Manual

23 August 2024

Vanson V-3150 Manual

23 August 2024

Vanson V-878 Manual

23 August 2024

Batterioplader Manualer

Nyeste Batterioplader Manualer

Powertec BC2A-Li40V Manual

5 December 2025

Scheppach BC3A-Li18V Manual

4 December 2025

Schumacher SC1280 Manual

4 December 2025

Aqiila Sunbird P100 Manual

3 December 2025

Schumacher SC1361 Manual

3 December 2025

Alogic Smartbox SB-DCS7C Manual

3 December 2025

Dometic SinePower DSP 1524 Manual

3 December 2025

Dometic SinePower DSP 1512 Manual

1 December 2025

Dometic SinePower DSP 1024 Manual

28 November 2025

CamLink Omega Manual

26 November 2025