Velbus VMBSTART-W-10 Manual

Velbus Ikke kategoriseret VMBSTART-W-10

Læs gratis den danske manual til Velbus VMBSTART-W-10 (5 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 28 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 14.5 anmeldelser. Har du et spørgsmål om Velbus VMBSTART-W-10, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/5

Quick start guide VMBSTART-x-10

Pagina van 1 5

Congratulations on your purchase of the Velbus Starter Kit!

This quick start guide will walk you through the installation step by step.

Need a more detailed manual? Scan the QR code to access the

product page and find additional support under the "Support" tab.

Step 1: Connecting the Components

Connect the components of the set as shown on the connection diagram:

Important notes:

• You can add multiple Velbus DIN rail modules between

the VMBUSB and VMB4RYNO modules.

• Use the included Molex cable to connect the

VMB4RYNO module to the VMBPSU module. Cut off

one side of the Molex connector, strip the black (-)

and red (+) wires, and connect them to the VMBPSU.

• The Molex connections on the VMB4RYNO and

VMBUSB modules are internally connected. It does

not matter which port you use.

• Each DIN rail module comes with a Molex cable for

daisy-chaining the bus. Need additional (longer) cables?

See our and

VMBCABLE20SET, VMBCABLE40SET

VMBCABLE150SET.

• Strip both ends of the EIB cable and connect them to

the connectors on the VMBELO and VMBUSB

modules. Follow the color coding of the bus

connections:

Red Voltage 15V (± 3V) +

Black Voltage - 0V

White CANbus Low L

Yellow CANbus High H

Overview cable sets:

Quick start guide VMBSTART-x-10

Pagina van 2 5

Step 2: Configuring the Terminators

All Velbus modules (except the VMBUSB-20) are equipped with a terminator (a switch marked "TERM") that is

open by default. In every Velbus installation, at least two terminators must be closed, with as much cable

distance as possible between them. These are usually the first and last (farthest) modules in the installation.

For DIN rail modules, open the front panel to access the terminator. For other modules, the terminator is

located on the back. The terminator is enabled when the corresponding LED is lit.

In this basic setup, close the terminator on both the VMBELO panel and the VMB4RYNO module.

Step 3: Checking the BUS Connection

Velbus is a highly stable system, but any issues are usually caused by poor BUS connections.

Always perform the following check during the initial installation and after any cabling changes:

Press any button on a module (except the RESET button). You will see the LED next to the TX (transmit)

marking light up briefly. At the same time, the RX (receive) LEDs on all other modules in your installation will

also briefly light up. This indicates that a signal from the module is correctly placed on the bus and received by

the other modules.

Repeat this test for all other modules in your installation (except for the VMBUSB module, as it has no

buttons). If the other modules do not respond to the signal, double-check the cabling and follow our

troubleshooting guide.

Step 4: Programming via PC

• Download the latest Velbuslink software from . www.velbus.eu/downloads

The installation does not require admin rights unless you want to install the optional USB drivers.

• Connect the VMBUSB module to your computer using the included USB

cable after installing Velbuslink, and start the program.

• Click on "New" (top left) to start the "Create a new project" wizard.

Select for the following options: "Connect to an existing installation" Next

a "Direct connection via cable". nd

Produkt Specifikationer

Mærke:	Velbus
Kategori:	Ikke kategoriseret
Model:	VMBSTART-W-10

Har du brug for hjælp?

Hvis du har brug for hjælp til Velbus VMBSTART-W-10 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Velbus Manualer

Velbus VMBSTART-B-10 Manual

27 Januar 2025

Velbus VMBSTART-W-10 Manual

27 Januar 2025

Velbus VMB6PBN Manual

28 December 2024

Velbus VMBPIRO-W-20 Manual

23 November 2024

Velbus VMBPIRO-B-20 Manual

22 November 2024

Velbus VMBPIRO-B-10 Manual

3 September 2024

Velbus VMBPIRO-W-10 Manual

3 September 2024

Velbus VMBPIR-20 Manual

1 September 2024

Velbus VMBELO-W-20 Manual

27 August 2024

Velbus VMBRFR8S Manual

21 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Navman MiVue 540 Manual

2 August 2025

Pro User PSI2000TX Manual

2 August 2025

Guede 5T Manual

2 August 2025

Navman EZY40 Manual

2 August 2025

Thule Chariot Ski kit Manual

2 August 2025

Hozelock 5102 Manual

2 August 2025

ART 310 Manual

2 August 2025

Gorenje KAS53ZDCINVFT Manual

2 August 2025

Gorenje KAS35ZDCINVFT Manual

2 August 2025

Navman MY450LMT Manual

2 August 2025