Velleman HAM982K Manual

Velleman Sikkerhed HAM982K

Læs gratis den danske manual til Velleman HAM982K (52 sider) i kategorien Sikkerhed. Denne vejledning er vurderet som hjælpsom af 42 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 21.5 anmeldelser. Har du et spørgsmål om Velleman HAM982K, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/52

HAM982K 1 VELLEMAN

HAM982K – HOME ALARM STARTER SET

Introduction

Thank you for buying the HAM982K! Please read the manual thoroughly before bringing this device into service.

If the device was damaged in transit, don't install or use it and contact your dealer.

The HAM982K home alarm set comprises:

1. 1 x electronic siren

2. 1 x AC power adapter

3. 1 x PIR detector

4. 5 x magnetic reed switches

5. 1 x panic button

6. 1 x 8-zone alarm control panel

These numbers refer to the chapters below.

1. Electronic Siren

5" horn speaker

Operating voltage 6-12Vdc

Peak output power 7W

Current consumption 600mA

Connection diagram: + =red wire

- = black wire

It is important to know if the N.O. contact is of the positive or the negative type. If it is a positive type, connection

should be made as shown above. If it is a negative type, the switch should be on the black (-) wire.

2. AC Power Adapter

Input voltage 230Vac 50Hz

Output voltage 16.5Vac

Output current 3000mA max.

Rated power factor cos φ 0.96

Protection built-in thermal & current fuse

Dimensions (LxWxH) 76 x 89.5 x 62mm

Weight 1.2kg

Connect the 16.5Vac output terminals to the device's input terminals. Make sure its power consumption does not

exceed the maximum rating of the adapter, and that the connection wires are firmly fixed to the terminals.

Then plug the power plug into a 230Vac mains socket.

The power adapter is for indoor use only.

HAM982K 2 VELLEMAN

1M 2M 3M 4M 5M 6M 7M 8M 9M 10M 11M 12M

42.1░

-42.1

3. PIR Detector

a. Technical Specifications

Detection element low noise dual element pyro sensor

Operating voltage 8-16Vdc ; 12Vdc nominal

Current consumption typical 15mA at 12Vdc

Power-up delay typical 2 minutes with flashing LED indication

Alarm period 2-3s

Alarm output N.C. relay contact with 10Ω in-line resistor. Contact rating: 28Vdc, 0.1A

Walk test with LED alarm indicator

Pulse counting Normal response or 2 pulses within 12 seconds for "harsh" environments

Tamper switch N.C. contact with 10Ω in-line resistor. Contact rating: 12Vdc, 50mA

Operating temperature -10 to +55°C

Humidity max 95% non-condensing

EMC conform to CE standard

Dimensions (HxWxD) 116 x 73.5 x 74mm

b. PCB layout

1. Pyro-sensor (do not touch this sensor!)

2. Walk test & alarm indicator

3. Tamper switch

4. Pulse count jumper ("harsh": for environment with high risk of false detection)

5. LED on/off jumper (on = flashing during start-up, on during operation)

6. Connection terminal block:

Tamper: if a tamper switch is required, connect these terminals to a 24h

normally closed (NC) zone in the alarm control panel. Opening the

housing will trigger a tamper signal.

12Vdc: connect (+) to an 8-16V power source, usually from the alarm control

panel. Connect (-) to the common grounding point.

Alarm: the alarm output relay of the detector. Connect these terminals to a

normally closed (NC) zone in the alarm control panel.

c. Installation

• Install the detector indoors, on a stable surface with a clear view on the protection area.

• Avoid mounting where hot or cold air may blow directly onto the device and where objects

in the detection field may change temperature rapidly (heating or air-conditioning devices).

• Considering the detection angle of the device (see figure on the right), corner mounting is

recommended, at a height of 2 to 3 meters.

Procedure:

1. Open the cover by inserting a small screw driver into the edge of the unit and turning it to release the cover.

2. Remove the PCB by releasing the two fixing screws from the support post - DO NOT DROP THE PCB!

3. Numerous "knockouts" are provided on the back plate. Punch the one which will provide the best cable entry.

4. The two fixing holes on the back of the back plate are for surface mounting. The two fixing holes on the left and

right of the back plate are for corner mounting. Fix the back plate firmly on the wall with the two enclosed screws.

5. Put the PCB back onto the back plate and fix it firmly. Connect the wires to the terminal block.

6. Clip the front cover back in place on the back plate. See to it that the tamper switch is depressed when the front

cover is in place.

Produkt Specifikationer

Mærke:	Velleman
Kategori:	Sikkerhed
Model:	HAM982K

Har du brug for hjælp?

Hvis du har brug for hjælp til Velleman HAM982K stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Sikkerhed Velleman Manualer

Velleman HAM982K Manual

12 August 2024

Sikkerhed Manualer

Nyeste Sikkerhed Manualer

Aritech SHATTERPRO 3 Manual

15 Januar 2025

Axis Camera Station S9001 Mk II Desktop Terminal Manual

15 Januar 2025

Eminent EM6511 Manual

15 Januar 2025

Ranex RX2567-Z Manual

11 Januar 2025

NetworX NX-595E IP Communication Module Manual

5 Oktober 2024

Provision-ISR NVR2-4100P Manual

23 September 2024

Gira 0342 Manual

23 September 2024

Unitron Smart Alert Systeem Manual

23 September 2024

Netatmo Welcome Manual

21 September 2024

NetworX NX-408 Manual

20 September 2024