Vemer EV2M-4DIN Manual

Vemer Ikke kategoriseret EV2M-4DIN

Læs gratis den danske manual til Vemer EV2M-4DIN (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 13 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 7 anmeldelser. Har du et spørgsmål om Vemer EV2M-4DIN, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/2
Mod. EV2M-2DIN
EV2M-4DIN
EV2M-R
V3IS00443–010
EV2M-2DIN
EV2M-4DIN
EV2M-R
EV2M-2DIN
EV2M-4DIN
EV2M-R
EV2M-2DIN
EV2M-4DIN
EV2M-R
Power supply connection terminals
Voltage reading window
Current reading window
Parameter setting key
Metering connection terminals
36 60
45
65
88
72 60
45
65
87
5
72 75
72
66
L
N
1
3
5
6
8
COM I V
LOAD
L
N
COM I V
1
3
10
11
13
LOAD
5 4 3 12
L
N
LOAD
P1P2
P1P2
P1P2
EV2M-2DIN
TRUE RMS
kA
V
A
Prg
Input 5(6)A 600 V~
PRG
A
V
Input 5(6)A~ 600 V~
TRUE RMS
kA
EV2M-4DIN
V
A
kA
EV2M-R
TRUE RMS
Input 5(6)A 600 V~
Prg
User Manual
DIGITAL VOLMETER-AMMETER
Read all the instructions carefully
The EV2M meters are digital multimeters to measure TRMS values (true
root mean square values) for alternate voltage and current. It reads these two
quantities simultaneously on two 3-digit LED displays.
SAFETY WARNINGS
During the installation and operation of the instrument, proceed in accordance
with the instructions below:
1) The instrument should be installed by a competent operator following the
installation diagrams carefully
2) Before touching the connector terminals make sure that the wires to be connected
or already connected to the instrument are not live
3) The instrument should be installed in a panel from which no access can be gained
to the terminals after installation
4) Do not power or connect the instrument if any part of it is damaged
5) The electrical system of the building in which the instrument is to be installed
should have a switch and a protective device against over-currents
6) The instrument is designed for installations with over-voltage category III and
pollution level 2, in accordance with the EN 61010-1 standard.
Code Model Description
VE149100 EV2M–2DIN Voltage-current reading meter 2 DIN
VE196200 EV2M–4DIN Voltage-current reading meter 4 DIN
VE195400 EV2M–R Voltage-current reading meter 72 x 72
TECHNICAL SPECIFICATIONS
• Power supply: 230 V AC (-15%/+10%), 50/60 Hz
– maximum consumption: 4 VA
• Measurement of true root mean square (TRMS) values for voltage and current
• Voltmeter connection:
– connection type: direct
– maximum voltage: VMAX = 600 V
– maximum consumption: 2,5 VA
• Ammeter connection:
– connection type: by AT x/5 A
– available scales: from 5/5 A to 1000/5 A
– maximum and nominal current rating: In = 5 A; IMAX = 6 A
– maximum consumption: 2,5 VA
• Reading filter (update speed)
• Maximum section of wires:
– 6 mm2 for model EV2M-2DIN and EV2M-4DIN
– 2,5 mm2 for model EV2M-R
• Operating conditions:
– operating temperature: –10 ÷ +45 °C
– relative humidity: 10% ÷ 90% non-condensing
• Storage temperature: –20 ÷ +60 °C
• Display: 7-segment LED digit display
• Enclosure:
– 2 module DIN, RAL 7035 gray for EV2M-2DIN
– 4 module DIN, RAL 7035 gray for EV2M-4DIN
– standardized dimensions 72 x 72 mm according to DIN 43700 for EV2M-R
• Protection rating: IP51 on the front
RESOLUTION AND ACCURACY
• Voltage (full scale V MAX
= 600 V):
– Maximum reading: 615 V
– Minimum reading: 10V
– Resolution: 1V
– Accuracy: ± 0,5% full scale ± 1 digit (from 3% to 100% of full scale value)
• Current (full scale In = 5 A):
– Maximum reading: 6 A
– Minimum reading: 0,02 A
– Resolution: 0,01 A
– Accuracy: ± 0,5% full scale ± 1 digit (from 3% to 100% of full scale value)
Note: current data refer to the values provided by the amperometric transformer;
maximum and minimum readings directly depend on the AT ratio used, whereas
resolution is dependent on the scale used, as described below.
OPERATION
During normal operation the device reads the Voltage value (Volts) in the top window and the
current value (Amperes) in the bottom window.
The current value is automatically read in the most appropriate scale:
• 0,01 A resolution in the 0,02 A ÷ 10 A range (e.g.: )6.47
• 0,1 A resolution in the 10 A ÷ 100 A range (e.g.: )39.1
• 1 A resolution in the 100 A ÷ 1000 A range (e.g.: )528
• 10A resolution for values above 1000 A (e.g.: : )1.03
In the latter case the value is expressed in kA with the decimal point lit after the first digit and
the LED point lit to the right of the last digit above the kA symbol
SETTINGS
After switching the device on it is possible to check and/or change some of the factory settings
by pressing or holding down the key according to the procedure described below.Prg
• Press the Prg key
The voltage and current reading displays will read a value
referring to the transformer primary (factory setting: 5).
To change this value, hold down the key for at least 2 Prg
seconds until the digits fl ash. Then press and hold the key
pressed until the desired value is reached (the reading will
increase by 5-unit steps; 1000 is read as ).001.
• After a few seconds from the moment the key is released, a value
will indicate the reading fi lter (factory value: 10). The lower this
value, the faster the readings will be updated, the higher the
value, the more stable the reading will be.
To change this value, hold down the key for at least 2 Prg
seconds until the digits fl ash. Then press the key repeatedly
until the desired value is set (the reading will increase by 1-unit
steps; the value range is from 1 to 20).
After one of these parameters is set the device will go off and
then on again using the new parameters. The device is reset
automatically with no need to disconnect it from the power supply.
ERROR MESSAGES
• Memory error: EEE
The device has undergone damage that jeopardizes operation
• Overload error: KKK
The quantity measured (voltage and/or current) has exceeded the
maximum admissible value: V > 1,02 x VMAX; I > 1,2 x In.
Reset is automatic.
REFERENCE STANDARS
Conformity to the EU directives:
2006/95/CE (Low Voltage)
89/336/CEE mod. modified by 92/31/EEC and 93/68/EEC (EMC)
is declared with reference to the following harmonised standards:
EN 61010-1, EN 61000-6-2 and EN 61000-6-4
Dimensions
Dimensions
Dimensions
Connection
Connection
Connection
Description
Description
Description

Produkt Specifikationer

Mærke: Vemer
Kategori: Ikke kategoriseret
Model: EV2M-4DIN

Har du brug for hjælp?

Hvis du har brug for hjælp til Vemer EV2M-4DIN stil et spørgsmål nedenfor, og andre brugere vil svare dig


Ikke kategoriseret Vemer Manualer

Vemer

Vemer Mini Time Manual

20 Juni 2025
Vemer

Vemer TCR Manual

2 Oktober 2024
Vemer

Vemer Set PC RF8 Manual

1 Oktober 2024
Vemer

Vemer ADR-D Vision Manual

22 September 2024
Vemer

Vemer ES Manual

10 September 2024
Vemer

Vemer Thalos RF Manual

3 September 2024
Vemer

Vemer VE 502E Manual

1 September 2024
Vemer

Vemer Elettrosonda Z Manual

25 August 2024
Vemer

Vemer VE LAN Manual

10 August 2024
Vemer

Vemer LCR048 Manual

10 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Dahua Technology

Dahua Technology EVS5036S-R Manual

1 November 2025
Dahua Technology

Dahua Technology LM24-F211 Manual

1 November 2025
Chief

Chief CMS495 Manual

1 November 2025
Philips

Philips SPT7308 Manual

1 November 2025
Cardo

Cardo Lazer Velovox Manual

1 November 2025
Dahua Technology

Dahua Technology XVR7108H-4K-I2 Manual

1 November 2025
Dahua Technology

Dahua Technology XVR5208/16AN-4KL-X Manual

1 November 2025
DAP-Audio

DAP-Audio ZA-9120DAB Manual

1 November 2025
Ikea

Ikea KVISSLE 401.980.18 Manual

1 November 2025
IFM

IFM EBC060 Manual

1 November 2025