Ventus W263 Manual

Ventus Vejrstation W263

Læs gratis den danske manual til Ventus W263 (4 sider) i kategorien Vejrstation. Denne vejledning er vurderet som hjælpsom af 47 personer og har en gennemsnitlig bedømmelse på 3.7 stjerner ud af 24 anmeldelser. Har du et spørgsmål om Ventus W263, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

W263-0 & W235-0

Features:

- Soil moisture

- Soil temperature

- Air temperature on the remote sensor

- Indoor air temperature

- Watering alert display & alarm setting

- Weather Forecast

- Digital clock with daily alarm

Battery installation:

Main unit W203GP:

- Open the battery door and insert 4 pieces of AA batteries according to the polarity shown

Remote sensor W235G0

- For first time use, pull out the plastic strip from the battery door

- For battery replacement, remove the battery door and replace with a new CR2450 battery

Setting up the sensor:

1) Hold the [Channel/Search] button on the main unit W203GP to search for the sensor

2) Select the channel number on the remote sensor by rotating to the desired channel number

3) Hold the [Tx] button inside the battery compartment of the plant sensor W235G0 to transmit

signal

4) Once RF synchronization is completed, the corresponding channel data will be displayed on

the main unit

To setup for another remote sensor, select different channel number on the sensor and follow

above procedure.

Soil moisture display:

Moisture Levels:

Wet 4 bars

Slightly Wet: 3 bars

Slightly Dry: 2 bars

Dry: 1 bar

Buttons & Operation

Key Operation:

[CH (channel) ]:

- Select channel from channel 1,2,3,4,5 & auto-scroll

- Hold to search for remote sensor

[Watering alarm on/off]

- Press to enable / disable the watering alarm

The “AL ((.))” icon appears when it is enabled

Watering alarm beeping pattern:

- Beeps once every 1 minute

- It does not beep from 9pm to 9am

[Up / C/F]

- Press to toggle between degree C & F

- Press to increase digit value in setting mode

[Down]

- Press to increase digit value in setting mode

[Max Min Memory]

- Press to show maximum, minimum & current air, indoor & outdoor temperature readings

- Hold 3 seconds to clear the memory

[Alarm (Bell)]

- Press to show alarm time. When alarm time display, press to on/off alarm.

- When alarm time display, press and hold 3 seconds to enter setting alarm time

[Clock]

- Press and hold 3 seconds to enter setting clock

[Snooze]

- When alarming, press the button to enter snooze.

CLOCK SETTING

Hold “CLOCK“ button for 3 seconds to enter clock set. Using “ + , - “ to adjust and “ CLOCK ” to

confirm, the following values can be set in sequence: Hr > Min > 12/ 24 >Existing Weather >

confirm & exit (if not confirmed, auto exit & save after 1 minutes)

ALARM SETTING

Press to view Alarm Time for 10 seconds.

Hold “ALARM“ for 3 seconds, Hr will flash, press “ +, - “ to enter the desired value and press

“ALARM“ to conﬁrm. Minute will flash, press “ +, - “ to enter the desired value and press

“ALARM“ to confirm. Alarm mode Zz will flash, press “ +, -“ to select Zz snooze alarm, (bell) daily

alarm or Alarm oﬀ (no icon). Zz snooze alarm will be enabled when user enter into alarm setting

each time.

SNOOZE

Press SNOOZE to trigger snooze alarm. To stop alarm for one day, press ALARM key but not

“SNOOZE” key.

Setting up the sensor:

1) Hold the [Channel/Search] button on the main unit W263 to search for the sensor

2) Select the channel number on the remote sensor by rotating to the desired channel number

3) Hold the [Tx] button inside the battery compartment of the plant sensor W235 to transmit

signal

4) Once RF synchronization is completed, the corresponding channel data will be displayed on

the main unit

To setup for another remote sensor, select different channel number on the sensor and follow

above procedure.

Soil moisture display:

Moisture Levels:

Wet 4 bars

Slightly Wet: 3 bars

Slightly Dry: 2 bars

Dry: 1 bar

WEATHER FORECAST

The unit predicts weather condition of the next 12 – 24 hours based on the change of atmospheric

pressure. The coverage area is around 30 – 50 km. The weather forecast is based on

atmospheric pressure change and is about 70-80% correct. As weather conditions cannot be

100% correctly forecasted, we cannot be responsible for any loss caused by an incorrect forecast.

Produkt Specifikationer

Mærke:	Ventus
Kategori:	Vejrstation
Model:	W263

Har du brug for hjælp?

Hvis du har brug for hjælp til Ventus W263 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Vejrstation Ventus Manualer

15 Juli 2025

14 Januar 2025

21 December 2024

31 August 2024

31 August 2024

31 August 2024

31 August 2024

17 August 2024

8 Juli 2024

8 Juli 2024

Vejrstation Manualer

Nyeste Vejrstation Manualer

La Crosse Technology WS7006 Manual

30 September 2025

23 September 2025

23 September 2025

23 September 2025

21 September 2025

Brandson 305419 Manual

15 September 2025

Brandson 306643 Manual

15 September 2025

Brandson 304632 Manual

15 September 2025

Brandson 304577 Manual

14 September 2025

Brandson 304465 Manual

14 September 2025