Vibiemme Domobar Double version 3 Manual

Vibiemme Kaffemaskine Domobar Double version 3

Læs gratis den danske manual til Vibiemme Domobar Double version 3 (3 sider) i kategorien Kaffemaskine. Denne vejledning er vurderet som hjælpsom af 22 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 11.5 anmeldelser. Har du et spørgsmål om Vibiemme Domobar Double version 3, eller vil du spørge andre brugere om produktet?

Side 1/3
Courtesy of:
Vibiemme Double Boiler Supplemental Instructions
Turning on and priming:
1. If reservoir model, rinse and fill the reservoir. If plumbed in version, connect and open
water supply (water softener and water pressure regulators requirements are covered
separately)
2. Plug the machine in and turn the switch to position “I” (one). The Power light on far right
will come on. NOTE: Setting the rotary switch to position “I” will activate all the
functions of the machine such as the autofill circuit, power to the PID, power to the
pump, solenoid valve, microswitch for the lever and power the brew boiler heating
element (but not the steam boiler heating element). The machine should arrive with the
PID turned off and it is very important for the PID to remain OFF until both of the boilers
are primed. When the PID is OFF, there is no power supplied to the brew boiler heating
element.
Upon turning the switch to position “I” the display will turn on and show the software
version (ex. 1.00). Then after few seconds, the word OFF will appear. If OFF is not
displayed and you see a temperature reading instead, immediately push and hold the right
side button on the PID to turn it off.
3. Within a few seconds the autofill should turn on (you will hear the pump) and the steam
boiler will fill until the proper level is reached. For reservoir models keep an eye on the
water reservoir and make sure that the water level is going down.
4. It is possible that the steam valve and hot water spout have been opened for shipping,
especially in the winter months to avoid freezing issues. If they are open, now is a good
time to close them. However, if they arrived closed, now is a good time to open them to
release negative/cold air that may have accumulated in the boiler.
5. After the steam boiler’s autofill is completed, engage the grouphead lever (pump will
start again). Allow a few ounces of water to flow out the group, and then turn the lever
down (off).
Now both of the boilers of your machine are primed.
6. At this point, turn the PID ON by pushing and holding the right button. The word OFF
will disappear and the PID will start reading brew boiler temperature. For the US market,
the default temperature reading is in degrees F. If you prefer degrees C it can easily be
changed with the instructions we will cover further along.
7. The steam boiler can now be turned on by turning the switch to position II (the left light
will come on indicating that power is passing through the pressurestat and reaching the
heating element).
v.7/09 1
NOTES regarding the steam boiler: it takes about 5 minutes for the steam boiler to reach
temperature. The steam boiler also provides hot water to the water spout. During warm up, it is
normal to hear the anti-vacuum valve hissing until enough pressure has built inside the boiler to
shut the valve.
8. Once the pre-set pressure has been reached, the pressurestat will terminate power to the
heating element and the left light will go OFF. Let out a couple of steam bursts and you
are ready to steam milk.
Thanks to the double-boiler technology, there are separate circuits within the machine for heating
the brew boiler and the steam boiler. Personally, I recommend leaving the power switch in
position “I” (thus NOT connecting disengaging the steam heating element) unless you are
preparing to steam milk or lengthen shots with hot water (Americano).
There are a few advantages to leaving an unused steam boiler off:
Less maximum electricity consumption (600w versus 1600w)
Less heat dispersion into the ambient
Less wear and tear on some components
Safer if you intend to put your machine on a timer.
PID Function:
Although the PID is pre-set by the factory, one convenience of the double boiler machine is that
you can customize your brewing temp without sacrificing steam pressure. (PID vs. pressurestat.)
WARNING: you can really mess up the settings, so if you have to change some parameters, make
sure you jot down the original settings in your owner’s manual before following these steps:
Changing from C to F or vice versa:
1. Turn the machine off
2. While holding both buttons of the PID (- & +), turn the machine back on.
3. Keep holding the buttons. The display will show the software version (ex. 1.00)
4. In 3 seconds, the display will show F03. You are now in programming mode.
5. Release both buttons and push the right button until the display shows F.
6. Stop pushing buttons. After 3 seconds, the display will go back to F03.
7. You are now in F. Turn machine off and back on.
To scroll from F to C push the RIGHT button until the desired value is shown.
WARNING: IF YOU TOUCH THE LEFT BUTTON WHILE IN PROGRAMMING MODE,
YOU WILL MODIFY THE PID PARAMETER, MAKING THE MACHINE FUNCTION
IMPROPERLY.
IF you must modify the PID values, then once in the F03 mode:
1. Push the left button; display will show P.
2. Once P is displayed, push the right button.
3. The set value will show (ex 1.8).
v.7/09 2


Produkt Specifikationer

Mærke: Vibiemme
Kategori: Kaffemaskine
Model: Domobar Double version 3

Har du brug for hjælp?

Hvis du har brug for hjælp til Vibiemme Domobar Double version 3 stil et spørgsmål nedenfor, og andre brugere vil svare dig