Vitamix Ascent A3300i Manual

Vitamix Køkkenmaskine Ascent A3300i

Læs gratis den danske manual til Vitamix Ascent A3300i (2 sider) i kategorien Køkkenmaskine. Denne vejledning er vurderet som hjælpsom af 69 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 35 anmeldelser. Har du et spørgsmål om Vitamix Ascent A3300i, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

PRINTER’S INSTRUCTIONS:

INSTR,INSTL,IRE-1.0 • LINEAR P/N: 223101X20 • INK: BLACK •

MATERIAL: 20LB. GLOSS WHITE PAPER • SIZE: 4.250” X 17.500” FOLD TO 4.250” X 3.500”

• FOLDING: 5 PARALLEL FAN-FOLDS, FINISH WITH LOGO SHOWING • SCALE: 1-1

223101X20 • IMAGE 1

DESCRIPTION

The IRE-1.0 represents the highest level in sophistication for attachable

IR Emitters. It features a unique EZ-Docker

™ port that permits instant

removal of the emitter when rearranging or servicing components.

An improved adhesive reduces callbacks for reattachment of “fallen

emitters”. The case may also be taken apart so that the tiny internal

emitter can be placed inside a component, when desired. High IR

output from the top curved surface allows emitter to be mounted

on a nearby surface, below, above or on a cabinet door, rather than

directly on the sensor of the unit where conditions permit.

ATTACHMENT

First, locate the component’s IR sensor window and (see Note 1)

thoroughly clean it of any fingerprints or other greasy substances.

The EZ-Docker™ port has a clear adhesive layer on its bottom surface.

Peel the protective layer off,

exposing the adhesive.

Orient the port vertical (see

Fig. 2) and press it over the

center of the component’s

sensor window. Press and

hold for several seconds to

ensure maximum contact

of the adhesive.

Slide the emitter from the

top down, into the EZ-

Docker™ port. You should

feel it “snap” into place. (To

remove the emitter at any

time, simply push upward

until it “pops” out).

IRE-1.0

Emitter

8 FT 9/16"

7/16"

3.5mm

mini plug

1/4"

Side View

Emitter

Wire Lead

Docki ng

Port

Clear Adhe sive Tape

(See Note 3)

Top View

NOTE: White striped side is posit ive ( +)

(– )

(+ )

Emitter slides in to

Docki ng Port

TYPICAL INSTALLATION

Satellite Receiver

PS-1.0

IRE-1.0

Emitter

IRE-1.0

Emitter

VCR

A/V Receiver

Hand Held

Remote

IRC-3.0

Emitter

IR Sensor

Window

AT-1.0

Amplified Terminator

Unit

Power Supply

120V AC

(unswitched)

Shelf Top

IR Receiver

Fig. 1

Insert the 3.5mm plug into an Emitter jack on a SpeakerCraft

Terminator or other source of IR (see Fig. 3)

CAUTION: Do not plug into an emitter jack that is set to Blaster

Power (BL ON) or to the HIGH OUT of other connecting blocks.

To do so will smoke the emitters!!

Note 1: If you have difficulty finding the component’s IR sensor, try

using a flashlight. Sometimes the owner’s manual is helpful. You may

need to contact the manufacturer direct.

Note 2: You may also attach the emitter without the EZ-Docker

™

port. Use one of the spare adhesives (included) applying it directly to

the bottom surface of the IRE-1.0 shell.

Note 3: If you need to remove the EZ-Docker™ port or emitter previ-

ously stuck to a component’s surface, use a fresh adhesive (included)

before reattaching.

Note 4: The emitter shell and EZ-Docker™

port, though dark in

appearance, are transparent to Infrared. This allows IR commands

to pass through them, permitting local hand held remote control as

well as through the IRE-1.0.

Fig. 3

IR Controlled Components

IR sensor

window

Docking Port

IRE-1.0 attached to

IR sensor window

2) Slide EmitterIRE-1.0

end into docking port

1) Attach Docking PortIRE-1.0

to IR sensor window with adhesive pad

Fig. 2

PRINTER’S INSTRUCTIONS:

INSTR,INSTL,IRE-1.0 • LINEAR P/N: 223101X20 • INK: BLACK •

MATERIAL: 20LB. GLOSS WHITE PAPER • SIZE: 4.250” X 17.500” FOLD TO 4.250” X 3.500”

• FOLDING: 5 PARALLEL FAN-FOLDS, FINISH WITH LOGO SHOWING • SCALE: 1-1

223101X20 • IMAGE 2

IR Controlled Components

IR Sensor

Window

Fig. 5a IRE-1.0 attached directly

to IR sensor window

Cabinet Door

Fig. 5b IRE-1.0 attached to inside of

cabinet door directly opposite

IR sensor window

IRE-1.0 attached to shelf directly

below or above IR sensor window

Fig. 5c & d

Fig. 5

Low

output side

toward IR

sensor

Connecting

lead

Emitter

Shell

High

output

side

Internal

IR Emitter

In others, it may be necessary to remove the internal emitter from its

shell so that it will fit in tiny chassis places. In this case, use the thin

edge of a knife to carefully pry the lower cover from the shell of the

emitter. Gently ease the tiny emitter and lead from it’s nest within the

shell. Use heat shrink tubing, or other insulating means, to prevent

shorting of the exposed leads.

Fig. 4

IRE-1.0

IR Emitter

SmartPath™

INSTALLATION INSTRUCTIONS

LIT03100 (rev2)

223101X20

940 Columbia Avenue, Riverside, CA 92507 • Phone 1-800-448-0976 • Fax 951-787-8747

www.speakercraft.com

LIMITED 5-YEAR WARRANTY

SpeakerCraft Inc. warrants to the original retail purchaser only that this

SpeakerCraft product will be free from defects in materials and workman-

ship, for a period of 5-years, provided it was purchased from a SpeakerCraft

Authorized Dealer.

Defective products must be shipped, together with proof of purchase,

prepaid insured to the SpeakerCraft Authorized Dealer from whom they

were purchased, or to the SpeakerCraft factory at the address listed on this

installation instruction manual. Freight collect shipments will be refused. It

is preferable to ship this product in the original shipping container to lessen

the chance of transit damage. In any case, the risk or loss or damage in

transit is to be borne by the purchaser. If upon examination at the Factory

or SpeakerCraft Authorized Dealer it is determined that the unit was defec-

tive in materials or workmanship at any time during this warranty period,

SpeakerCraft or the SpeakerCraft Authorized Dealer will, at its option, repair

or replace this product at no additional charge, except as set forth below.

If this model is no longer available and can not be repaired effectively,

SpeakerCraft, at its sole option may replace the unit with a current model of

equal or greater value. In some cases where a new model is substituted, a

modification to the mounting surface may be required. If mounting surface

modification is required, SpeakerCraft assumes no responsibility or liability

for such modification. All replaced parts and product become the property

of SpeakerCraft Inc. Products replaced or repaired under this warranty

will be returned to the original retail purchaser, within a reasonable time,

freight prepaid.

This warranty does not include service or parts to repair damage caused

by accident, disaster, misuse, abuse, negligence, inadequate packing or

shipping procedures, commercial use, voltage inputs in excess of the rated

maximum of the unit, or service, repair or modification of the product which

has not been authorized or approved by SpeakerCraft. This warranty also

excludes normal cosmetic deterioration caused by environmental conditions.

This warranty will be void if the Serial number on the product has been

removed, tampered with or defaced.

This warranty is in lieu of all other expressed warranties. If the product is

defective in materials or workmanship as warranted above, the purchaser’s

sole remedy shall be repair or replacement as provided above. In no event

will SpeakerCraft be liable for any incidental or consequential damages

arising out of the use or inability to use the product, even if SpeakerCraft

Inc. or a SpeakerCraft Inc. Authorized Dealer has been advised of the pos-

sibility of such damages, or for any claim by any other party. Some states

do not allow the exclusion or limitation of consequential damages, so the

above limitation and exclusion may not apply. All implied warranties on the

product are limited to the duration of this expressed warranty. Some states

do not allow limitation on the length of an implied Warranty. If the original

retail purchaser resides in such a state, this limitation does not apply.

Other Emitter Placements

Since the IRE-1.0 has high output from it’s curved top , (See Fig. 4)

you may attach it to other surfaces nearby, if the installation permits.

(See Fig. 5)

Use the higher power setting (NOT Blaster Power) on the connect-

ing block or terminator, if so provided.

Some installers like the option of placing the emitter completely inside

a component, as near as possible to the IR sensor, for a clean external

appearance. In some cases, the whole emitter can be so placed.

ELT03100

SpeakerCraft®

Produkt Specifikationer

Mærke:	Vitamix
Kategori:	Køkkenmaskine
Model:	Ascent A3300i

Har du brug for hjælp?

Hvis du har brug for hjælp til Vitamix Ascent A3300i stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Køkkenmaskine Vitamix Manualer

Vitamix The Quiet One Manual

12 Februar 2024

Vitamix Ascent A3300i Manual

29 Maj 2023

Køkkenmaskine Manualer

Nyeste Køkkenmaskine Manualer

Kenwood CookEasy+ CCL50 Manual

16 August 2025

Philips HR7962 Manual

15 August 2025

Sencor STM 3757TQ Manual

14 August 2025

Sencor STM 3787CH Manual

14 August 2025

Sencor STM 3752BL Manual

14 August 2025

Sencor STM 4467CH Manual

14 August 2025

Sencor STM 3756YL Manual

14 August 2025

Sencor STM 3754RD Manual

14 August 2025

Bestron Kitchen Master AKM2000 Manual

14 August 2025

Tefal Masterchef Compact QB2001 Manual

13 August 2025