Vivanco UR 810 Manual

Vivanco Fjernbetjeninger UR 810

Læs gratis den danske manual til Vivanco UR 810 (34 sider) i kategorien Fjernbetjeninger. Denne vejledning er vurderet som hjælpsom af 19 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 10 anmeldelser. Har du et spørgsmål om Vivanco UR 810, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/34

UR 810 UNIVERSAL CONTROLLER

Vivanco GmbH, D-22926 Ahrensburg, E-Mail

: hotline@vivanco.de

, Helpline: +49 (0) 4102 231135 1

(GB) Instructions 1 

(D) Bedienungsanleitung 3 

(F) Notice d’emploi 6 

(E) Instrucciones para el uso 9 

(I) Istruzioni per l’uso 11 

(NL) Gebruiksaanwijzing 14 

(PL) Instrukcja obsługi 16 

(CZ) Návod k obsluze 19 

(P) Manual de instruções 21 

(DK) Betjeningsvejledning 24 

(S) Bruksanvisning 26 

(RUS)

  

 28

(GR) 31   

(GB) Instructions

VIVANCO UR 810 remote control for almost all

TV, audio, video and other infrared-controllable

appliances

Inserting the batteries

Open the battery flap on the back of the remote

control, press the flap lightly downwards, then

insert 2 alkaline AAA batteries. Check that the

polarity markings on the batteries and in the

battery compartment are correctly lined up

(+=+), then close the flap carefully. – Always

use undamaged batteries.

Adapting to appliances

In order to control your appliances you must

adapt or set the remote control to them. There

are three ways of doing so: direct control code

entry, code search or learn.

If your UR 810 does not understand you, it

blinks several times and you can then repeat

the entry. Each understood entry is confirmed

by an appliance button blinking once briefly.

Direct control code entry using the

enclosed list

Example: setting to control a Panasonic

television set:

1. The enclosed list gives, for

example, the Panasonic Code 153.

Please make sure you have selected the

correct list for television sets (TV).

2. To prepare code entry, press the

SET button, keep it pressend and then press

the required appliance button, e.g. TV,

additionally until the lamp (LED) inside lights

constantly.

3. Then press the number buttons

(e.g. 1 5 3) in sequence.

4. Once the numbers have been

entered the button lamp goes out and the

remote control is ready to control your

appliance.

5. Finally, test the control code setting

by trying to control (in this example) your

television set. If it does not work at all or not

correctly try a different code from the list or the

code search (see below).

6. To set the remote control for other

appliances, proceed in the same way. Instead

of the TV appliance button, press another

button e.g. VCR, DVB (SAT, DECODER),

DVD).

Code search

If the brand of your appliance is not in the list

or none of the codes given fits, we recommend

a code search.

UR 810 UNIVERSAL CONTROLLER

Vivanco GmbH, D-22926 Ahrensburg, E-Mail

: hotline@vivanco.de

, Helpline: +49 (0) 4102 231135 2

Manual code search

1. Switch on the appliance to be

controlled. Program is running.

2. To prepare code search, press the

SET button, keep it pressed and then press the

required appliance button, e.g. TV, additionally

until the lamp (LED) lights constantly.

3. Then point the remote control at the

appliance to be controlled.

4. Briefly press the ON/OFF

(appliance on/off) button once. The lamp (LED)

blinks. – Except when searching for a TV code

you can also briefly press the yellow > (Play)

button and use the Play function to search.

Make sure that a tape, a DVD or a CD is

inserted in the tape deck, player or recorder.

5. Press the ON/OFF (appliance

on/off) or Play button repeatedly, approx. every

1,5 seconds, until the appliance, e.g. your DVD

player, reacts. - If you notice the reaction of

your appliance too late and the next code has

already been emitted you can go back by

pressing SET and then ON/OFF or Play again.

If your appliance has switched itself off you

must switch it back on again, e.g. on the

appliance or with the original remote control, to

continue searching. - When your appliance

reacts you can also try out other buttons

without interrupting the search. If some buttons

do not work properly, simply continue

searching with ON/OFF or Play.

6. When your appliance reacts

correctly, press the appliance button, e.g. TV,

and end the search. The lamp (LED) goes out.

- The UR 810 continues with the search at the

point where you interrupted it. When the end of

the code list is reached the search stops

automatically. The remote control blinks quickly

several times. The code last entered remains

stored. The search stops after approx. 30

seconds of inactivity.

Automatic code search

Your remote control finds the correct settings

almost automatically in seconds:

1. Switch on the appliance to be

controlled. A channel number, for example,

appears in the display of your satellite receiver.

2. To start the code search, press the

SET button, and then additionally the required

appliance button, e.g. TV, for more than 3

seconds until the lamp (LED) starts to blink.

3. Then point the remote control at the

appliance to be controlled while the remote

control emits a different ON/OFF signal every 2

seconds.

4. When your appliance reacts, press

any button, except SET, to end the search. – If

you ended the search too late, continue to

search using the Manual Code Search (see

above).

5. Finally, test the control code setting

by trying to control, for example, your DVD

appliance. If it does not work correctly, please

try the code search again. The code search

then begins with the next code in the

sequence. - Remember to switch your

appliance, e.g. DVD, back on again if you wish

to continue searching.

Code identification

You can read off the 3-digit codes you have set

at any time:

1. Press the appliance button of the

appliance which code you want to read off, e.g.

TV.

2. Press the button and 1,2,3, SET

depending on the part of the code you want to

read off. For example, if you press + after SET 1

TV and the code 156 (in this example) has

been set, the lamp blinks once after SET+1 is

released to show that the hundred figure is 1.

All you have to do is count. The ten figure is

indicated after + is released, e.g. it blinks SET 2

5 times for the 5 in 156. The one figure is

indicated after + is released, e.g. it blinks SET 3

6 times for the 6 in 156.

Learning, Programming, of Missing Control

Functions

The LEARN function is used to supplement the

preprogrammed codes. The standard code

may provide most of functions needed, but you

may miss some key functions. Or you didn´t

find any functioning preprogrammed code for a

device. You can capture upto 100 key funtion

codes, max 40 per device. The last captured

function will overwrite the previous. learnt.

1 For learning of key codes you must use a

functioning orginal remote controller. Please

use fresh batteries for both remote controls.

2 Please point the original´s remote control

transmitter LED towards the receiver LED of

UR 810 (placed on top, same as transmitter

LED). Distance of LEDs between both remotes

shall be approximately 30mm and must be in

straight line of sight.

3 Press down and hold the Learn key and

press the device key (e.g. DVD) additionally

and then release the both pressed keys. Then

e.g. the DVD device key starts blinking

indicating that DVD key codes (functions) can

be captured.

4 Press and release the target key, that

you want to learn to (reprogram) (e.g.

POWER), the device button lights up.

5 Press and hold the source key on the

Produkt Specifikationer

Mærke:	Vivanco
Kategori:	Fjernbetjeninger
Model:	UR 810

Har du brug for hjælp?

Hvis du har brug for hjælp til Vivanco UR 810 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Fjernbetjeninger Vivanco Manualer

Vivanco UR Zap 2 Manual

13 Juli 2024

Vivanco UR 850 LCD Manual

9 Juli 2024

Vivanco UR 820 LCD Manual

5 Oktober 2022

Vivanco UR 14 Manual

5 Oktober 2022

Vivanco UR 810 Manual

5 Oktober 2022

Vivanco UR 82 SE Manual

5 Oktober 2022

Vivanco UR 100 LCD Manual

5 Oktober 2022

Vivanco UR 81 Manual

5 Oktober 2022

Vivanco UR 2 Manual

5 Oktober 2022

Fjernbetjeninger Manualer

Nyeste Fjernbetjeninger Manualer

Ruwido Easytip 2 Manual

14 Oktober 2024

Technics RAK-SSA163XH Manual

13 Oktober 2024

Technics SA-GX350 Manual

13 Oktober 2024

Hama 00012086 3in1 Manual

12 Oktober 2024

One For All URC 3550 Super Easy Manual

11 Oktober 2024

Meliconi Personal 1 Manual

11 Oktober 2024

Logitech Harmony Smart Control Manual

10 Oktober 2024

Logitech Harmony 350 Manual

9 Oktober 2024

Telefunken TRC 800 Manual

9 Oktober 2024

T'nB RCOLORSI Manual

8 Oktober 2024