WAC Lighting MO-LED810 Manual

WAC Lighting Lys MO-LED810

Læs gratis den danske manual til WAC Lighting MO-LED810 (1 sider) i kategorien Lys. Denne vejledning er vurderet som hjælpsom af 2 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 1.5 anmeldelser. Har du et spørgsmål om WAC Lighting MO-LED810, eller vil du spørge andre brugere om produktet?

Side 1/1
WAC Lighting
www.waclighting.com
Phone (800) 526.2588 • Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive • Port Washington, NY 11050
Phone (516) 515.5000 • Fax (516) 515.5050
Western Distribution Center
1750 Archibald Ave • Ontario, CA 91761
Phone (800) 526.2588 • Fax (800) 526.2585
WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. JUNE, 2014
INSTALLATION INSTRUCTION
MO-LED810
SAFETY INSTRUCTION
IMPORTANT: NEVER attempt any work without shutting o the electricity.
Read all instructions before installing.
System is intended for installation by a qualied electrician in accordance with the National Electrical Code and
local regulations.
Go to the main fuse box, or circuit breaker. Place the main power switch in the “OFF” position and unscrew the fuse(s)
or switch ”OFF” the circuit breaker switch(es) that control the power to the xture or room that you are working on.
Place the wall switch in the “OFF” position.
CAUTION
All parts must be used as indicated in these instructions. Do not substitute any parts, leave parts out, or use any parts
that are worn out or broken. Failure to follow this instruction could invalidate the ETL/CETL listing of this xture.
AVERTISSEMENT
IMPORTANT : COUPEZ LÉLECTRICITÉ AVANT TOUTE MANIPULATION.
Lisez toutes les instructions avant d’installer.
Système est destiné à être installé par un électricien qualié en conformité avec le code national de l’électricité et les
règlements locaux.
Accédez au panneau central de disjoncteurs ou de fusibles de votre demeure et placez l’interrupteur principal en
position d’arrêt (« OFF »).
Placez l’interrupteur mural en position d’arrêt (« OFF »).
MISE EN GARDE:
Toutes les pièces doivent être utilisées tel qu’il est indiqué dans ces instructions. Ne remplacez pas les pièces, nen laissez pas
de côté et ne les utilisez pas si elles sont usées ou brisées. Le non-respect de ces instructions peut annuler l’homologation
ETL/CETL du luminaire.
FIXTURE INSTALLATION:
1. Loosen the three canopy screws, twist and separate the canopy cover from the base plate (keep screws on base plate ).
2. Remove a knock out from the base plate.
3. Attach the base plate to the surface using slotted holes for mounting screws (supplied).
4. Connect xture wires to 120V AC power wire, with wire nuts (supplied).
5. Connect ground wire to the green wire from xture.
6. Mount the canopy to the base plate by twisting key holes over three screws in base plate.
7. Tighten screws to secure canopy.
8. After the light is on, rotate the luminaire body horizontally or vertically to aim properly.
Framing Projector and Barn Doors (Ordered separately)
Installing Framing Projector or Barn Doors
These accessories are simply press-tted by hand into the
front of the xture


Produkt Specifikationer

Mærke: WAC Lighting
Kategori: Lys
Model: MO-LED810

Har du brug for hjælp?

Hvis du har brug for hjælp til WAC Lighting MO-LED810 stil et spørgsmål nedenfor, og andre brugere vil svare dig