Westinghouse Iron Hill 6129200 Manual

Westinghouse Lys Iron Hill 6129200

Læs gratis den danske manual til Westinghouse Iron Hill 6129200 (3 sider) i kategorien Lys. Denne vejledning er vurderet som hjælpsom af 12 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 6.5 anmeldelser. Har du et spørgsmål om Westinghouse Iron Hill 6129200, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/3

CHANDELIER MOUNTING AND WIRING INSTRUCTIONS

NOTE: Underwriters Laboratories (UL) does not require all fixtures to have ground wires. These fixtures

meet all UL specifications.

1. Turn off power at circuit box to avoid possible electric shock.

2. Thread mounting screws (A) into the cross bar (B).

3. Secure cross bar (B) to outlet box (C) with outlet box screws (D) (if applicable) (see fig. 1).

4. Affix the loop 1 (I) to the canopy (F) by hex nut (K) and star washer (J).

5. Thread stem (L) onto fixture.

6. Thread fixture cap (E) and loop 2 (I) onto stem (L), (carefully twist fixture cap (E) and loop 2 (I) to

stem (L), do not twist or kink wires)

7. Open one link on bottom end of chain (H). Attach to fixture loop 2 (I). Securely close link on chain (H).

8. Lace wires up through every other link on chain (H) then through canopy loop 1 (I), canopy (F) and

nipple (G).

9. Open one link on top end of chain (H). Attach to canopy loop 1 (I) and canopy (F). Securely close

link on chain (H).

10. Identify color coding of fixture wires (see fig. 3).

11. Connect the smooth wire with marking printed or molded from the fixture with the black wire

from outlet box (C) by wire connector (N), and wrap the wire connector (N) with electrical tape for

a more secure connection.

12. Connect the ribbed wire from the fixture with the white wire from the outlet box (C) by wire

connector (N), and wrap the wire connector (N) with electrical tape for a more secure connection.

13. Partially thread green grounding screw (O) into side hole (P) on cross bar (B).

14. Wrap grounding wire from fixture around green grounding screw (O) leaving enough excess

wire, then connect the excess grounding wire from the fixture with the grounding wire from outlet

box (C) by wire connector (N) (if applicable), then wrap the wire connector (N) with electrical tape

for a more secure connection.

15. Tighten green grounding screw (O). Do not over tighten.

16. Tuck wires inside outlet box (C).

17. Raise canopy (F) to ceiling over mounting screws (A).

18. Secure into place with cap nuts (Q).

SEMI-FLUSH MOUNTING AND WIRING INSTRUCTIONS

NOTE: Underwriters Laboratories (UL) does not require all fixtures to have ground wires. These fixtures

meet all UL specifications.

1. Turn off power at circuit box to avoid possible electric shock.

2. Thread mounting screws (A) into the cross bar (B).

3. Secure cross bar (B) to outlet box (C) with outlet box screws (D) (if applicable) (see fig. 2).

4. Thread stem (L) onto fixture.

5. Remove the loop 2 (I) from fixture cap (E).

6. Affix the canopy (F) to the fixture cap (E) by hex nut (K) and star washer (J).

7. Thread fixture cap (E) and canopy (F) onto stem (L), (carefully twist fixture cap and canopy to stem,

do not twist or kink wires)

8. Identify color coding of fixture wires (see fig. 3).

9. Connect the smooth wire with marking printed or molded from the fixture with the black wire

from outlet box (C) by wire connector (N), and wrap the wire connector (N) with electrical tape for

a more secure connection.

10. Connect the ribbed wire from the fixture with the white wire from the outlet box (C) by wire

connector (N), and wrap the wire connector (N) with electrical tape for a more secure connection.

11. Partially thread green grounding screw (O) into side hole (P) on cross bar (B).

12. Wrap grounding wire from fixture around green grounding screw (O) leaving enough excess wire,

then connect the excess grounding wire from the fixture with the grounding wire from outlet

box (C) by wire connector (N) (if applicable), then wrap the wire connector (N) with electrical tape

for a more secure connection.

13. Tighten green grounding screw (O). Do not over tighten.

14. Tuck wires inside outlet box (C).

15. Raise canopy (F) to ceiling over mounting screws (A).

16. Secure into place with cap nuts (Q).

FIXTURE ASSEMBLY INSTRUCTIONS

Warning: This fixture is for indoor use only.

1. Install lamp(s). Do not exceed recommended wattage.

2. Turn power back on at circuit box.

FIXTURE ASSEMBLY INSTRUCTIONS

Warning: This fixture is for indoor use only.

1. Install lamp(s). Do not exceed recommended wattage.

2. Turn power back on at circuit box.

Westinghouse Lighting, Philadelphia, PA 19154-1029, U.S.A. www.westinghouselighting.com

, WESTINGHOUSE, and INNOVATION YOU CAN BE SURE OF are trademarks of Westinghouse Electric Corporation.

WARNING

Turn off electricity to the mounting site before beginning installation.

Mounting instructions must be followed exactly as shown for the fixture to be safely supported.

CLEANING AND CARE

To clean, wipe fixture with soft cloth. Clean glass with mild soap. Spray from chemical cleaners can

discolor the finish of fixture. Do not use scouring pads, powders, steel wool or abrasive paper to

clean this fixture.

ORDERING PARTS

Keep this manual for future reference, and in case replacement parts are needed. Available parts can

be ordered from place of purchase. Use exact wording from diagrams when ordering parts.

FIGURE 2.

FIXTURE

WIRES:

Smooth

HOUSE

WIRES:

Black

(Hot)

HOUSE

WIRES:

White

(Neutral)

HOUSE

WIRES:

Bare

Copper

(Ground)

FIXTURE

WIRES:

Bare

Copper

(Ground)

FIXTURE

WIRES:

Ribbed

FIGURE 3.

*NOT SUPPLIED

Line art shown may not exactly match the

fixture enclosed. However, the installation

instructions do apply to this fixture.

FIGURE 1.

For Chandelier Mounting Option

*GROUND

WIRE

*LAMP

WIRE

CONNECTORS (N)

SIDE HOLE (P)

STAR WASHER (J)

HEX NUT (K)

GREEN

GROUNDING

SCREW (O)

LOOP 1 (I)

NIPPLE (G)

LOOP 2 (I)

FIXTURE CAP (E)

STEM (L)

CAP NUTS (Q)

CANOPY (F)

CHAIN (H)

CROSS BAR (B)

MOUNTING

SCREWS (A)

*OUTLET BOX

SCREWS (D)

*OUTLET

BOX (C)

FIXTURE CAP (E)

*NOT SUPPLIED

Line art shown may not exactly match the

fixture enclosed. However, the installation

instructions do apply to this fixture.

FIGURE 2.

For Semi-flush Mounting Option

*GROUND

WIRE

*LAMP

WIRE

CONNECTORS (N)

SIDE HOLE (P)

STAR WASHER (X)

HEX NUT (K)

GREEN

GROUNDING

SCREW (O)

STEM (L)

CAP NUTS (Q)

CANOPY (F)

CROSS BAR (B)

MOUNTING

SCREWS (A)

*OUTLET BOX

SCREWS (D)

*OUTLET

BOX (C)

W-481

042820

ASSEMBLY INSTRUCTIONS FOR INDOOR LIGHTING FIXTURE

Congratulations on your Westinghouse purchase. This fixture has been designed to give you many

years of beauty and service. For questions and comments, please visit www.westinghouselighting.

com/contact-us.

NOTE: Carefully unpack fixture and parts. Make sure all parts are included before discarding any pack-

ing materials (see figure 1).

Owner’s Manual

Indoor Lighting Fixture

Installation Instructions

Fixture Warranty

This Westinghouse lighting fixture is warranted against defects in material and workmanship for a period

of five years from purchase date. This warranty is in lieu of all other warranties expressed or implied.

This warranty does not cover acts of nature such as lightening damage, or corrosion and discoloration

of components, nor does it cover damages caused through abuse, improver installation, surges in

electric current, or acts of third parties.

This warranty does not cover the costs of removing and re-installing the lighting fixture.

If this product fails for any reason covered by this warranty, please contact us at www.westinghouse-

lighting.com/contact-us.

WARNING:

ELECTRICAL SHOCK CAN RESULT IN SERIOUS INJURY.

Read and follow instructions exactly as shown. If instructions are unclear, do not proceed.

Contact a qualified electrician. Read all instructions before beginning. Proper wiring is essen-

tial for safe operation of this fixture. When cutting or drilling into walls or ceilings, do not dam-

age electrical wiring, gas lines, or water lines. If any of the fixture or wiring components are

damaged, do not install fixture. Return to place of purchase.

For fixtures provided with 75° C or 90° C supply wire warning only. (These warnings are provid-

ed on the U.L. label and on the fixture carton.) Risk of fire. Most dwellings built before 1985

have supply wires rated 60° C. Consult a qualified electrician before installing.

Produkt Specifikationer

Mærke:	Westinghouse
Kategori:	Lys
Model:	Iron Hill 6129200

Har du brug for hjælp?

Hvis du har brug for hjælp til Westinghouse Iron Hill 6129200 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Lys Westinghouse Manualer

Westinghouse Avery 6577100 Manual

22 August 2025

Westinghouse 72020 Manual

21 August 2025

Westinghouse Dorney 6128100 Manual

21 August 2025

Westinghouse Bexar 6125700 Manual

21 August 2025

Westinghouse Iron Hill 6129200 Manual

21 August 2025

Westinghouse Borgata 6129500 Manual

20 August 2025

Westinghouse Sylvestre 6127000 Manual

20 August 2025

Westinghouse Sirino 6575800 Manual

20 August 2025

Westinghouse Elway 6351500 Manual

14 Juli 2025

Westinghouse Porter 6575600 Manual

14 Juli 2025

Lys Manualer

Nyeste Lys Manualer

Esylux ELX EL LED 3h/8h IR SC SM Manual

31 December 2026

Dals FGM4-CC Manual

31 December 2026

Casalux AFL-1 Manual

31 December 2026

Craftmade Modina 38061 Manual

31 December 2026

Dals HPD4-CC Manual

31 December 2026

Craftmade Cubic 41528 Manual

31 December 2026

Dals HPD6-CC Manual

30 December 2026

Dals LNR24-CC Manual

30 December 2026

Dals LEDPNLRTF56-CC Manual

30 December 2026

Genaray SSL-36-RGB Manual

30 December 2026