Whirlpool ADG 4820 Manual

Whirlpool Opvaskemaskine ADG 4820

Læs gratis den danske manual til Whirlpool ADG 4820 (8 sider) i kategorien Opvaskemaskine. Denne vejledning er vurderet som hjælpsom af 29 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 15 anmeldelser. Har du et spørgsmål om Whirlpool ADG 4820, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/8
GB -1-
Chart
START/RESUME BUTTON
Push this button to start the selected program: the
indicator lights up and goes off at the end of the
program.
When the door is opened during a washing cycle,
the cycle is temporarily paused: the Start indicator
blinks. To resume the cycle close the door and
push Start button again.
PROGRAM SELECTION
BUTTON
Push “Programs” button
(repeatedly) until the indicator
of the required program lights
up (see “Table of programs”
below).
CANCEL/OFF BUTTON
Push this button to switch off the control panel.
If pressed when a program is running it cancels the
program ongoing draining water for 1 minute.
If pressed when the dishwasher is switched off it
drains any possible liquids from dishwasher (1
minute process).
If the indicator flashes repeatedly, see page 6 -
chapter ”What to do if ...”.
(see at right for options description)
1) Program data obtained in conformity with European standard EN 50242, obtained under normal conditions (without additional
options) and may vary depending on conditions. Differences of up to 20 minutes are possible with sensor programs as a result of the
appliance’s automatic calibration system.
2) Reference program for energy label in compliance with EN 50242 regulations. - Note for Testing Institutes: for detailed information
on the EN/Standard loading comparison test and other tests, contact the following address: “nk_customer@whirlpool.com”.
3) The antibacterial action has been tested by the Institut Pasteur of Lille (France), based on the NF EN 13697 standard of November 2001.
Table of programs Deter-
gent
Consumption
PPrograms Available
options Loading instructions Litres kWh Minutes 1)
1Pre-Wash cold Delay Crockery to be washed later. —4.0 0.03 14
2Quickwash 45°C Delay Lightly soiled crockery, with no dried-
on food. X11.0 0.80 30
3Eco 2) 50°C Delay Normally soiled crockery.
Energy-saving program. X12.0 1.05 165
4Antibacterial 3) Delay
Normally or heavily soiled crockery,
with additional antibacterial wash.
Program interruption (e.g. due to door
opening) can compromise elimination
of germs.
X13.0 1.50 115
5Intensive 70°C Delay Recommended program for heavily
soiled crockery, especially suitable for
pans and saucepans. X14.0 1.55 155
5019 396 01951ADG 4820
BEFORE USING THE APPLIANCE FOR THE FIRST TIME CAREFULLY READ
THIS QUICK REFERENCE GUIDE AND THE ASSEMBLY INSTRUCTIONS!
Options and display description
SALT INDICATOR
When lit (at the end of the
cycle), the salt reservoir
needs to be refilled.
DELAYED START
BUTTON
The wash cycle can be
programmed to start
after 2, 4 or 8 hours.
Then press the Start
button. The wash
program will start after
the set time.
RINSE AID INDICATOR
When lit (at the end of the
cycle), the rinse aid
dispenser needs to be
refilled.
THE CONTROL PANEL OF THIS DISHWASHER ACTIVATES PUSHING
ANY BUTTON EXCEPT CANCEL/OFF BUTTON.
FOR ENERGY SAVING THE CONTROL PANEL DEACTIVATES
AUTOMATICALLY AFTER 30 SECONDS IF NO CYCLE HAS STARTED.
TABLET SETTING
This setting allows to optimize the cycle performances
according the type of detergent used.
Push the Tablet button for 3 seconds (until the indicator
lights up) if you are using the combined detergents in
tablet (rinse aid, salt and deteregent in 1 dose).
If you are using powder detergent or liquid detergent,
the Tablet indicator on the control panel has to be off.
Quick reference guide
GB -2-
First time use
1- salt reservoir
2- rinse aid dispenser
3- detergent dispenser
4- racks system
5,6,7,8- available functions on the panel
9- filters
10- spray arms
1. Ask your water supply company what the
water hardness is... 2. ...enter this value on your
dishwasher Suggestions for detergent use
French
degrees °fH Water hardness
level
3 first PROGRAM LEDs
lit on the panel
(see table of programs)
P1 P2 P3
Gel or Powder
(rinse aid and salt) Tablets
0 - 9 Soft 1
go to step 1
(see “Daily
check”)
10 - 18 Medium 2
19 - 27 Average 3
28 - 37 Medium-hard 4if water is
HARD extra salt
needs to be added
(go to step 1,
“Daily check”)
38 - 50 Hard 5
51 - 63 Very hard 6
64 - 90 Extremely hard 7
Water hardness should be set only
before the first wash or if water
hardness has been changed
1Visual indicator
(depending
on the model).
Unscrew cap.
Fill the salt reservoir with water
before the first wash only.
(depending on the model)
The salt level indicator lamp may remain lit
at the end of several wash cycles. If the
water hardness level falls within category
(soft), no salt is required.
Salt indicator on the control panel Salt indicator on the salt reservoir cap
The indicator lamp lights up when SALT
NEEDS TO BE ADDED. green: OK. clear: NEEDS TO
BE ADDED
Daily check
Filling the salt reservoir - Dissolve limescale (not necessary if water hardness level is set to “soft”!)
-Press and hold together Programs and CANCEL/Off buttons for minimum 3 seconds.
- Programs LEDs will indicate the water hardness setting.
-Press the Programs button to increase setting (when the level reaches 7, the next key press will set the level back to 1.
- Wait 30 seconds (control panel switches off) or press START/Resume button to save setting.
Add salt (never add detergent!)
min. 0.8 kg / max. 1 kg
Water hardness level is factory
set for medium-hard water
(level 4).
Even if you use tablets which
include salt functionality, you
must still add regeneration salt
since such detergents are not
effective enough at softening
hard water.
Screw on the cap.
Salt residual
around the cap
need to be
removed. Some
salt reservoir have
a level indicator
integrated in the
cap (see below
how to check).
At first time use, the salt reservoir has to be filled independently from water hardness level (see description below in step 1 “Daily check”).
How to set water hardness in order to always assure the best cleaning results

Produkt Specifikationer

Mærke: Whirlpool
Kategori: Opvaskemaskine
Model: ADG 4820

Har du brug for hjælp?

Hvis du har brug for hjælp til Whirlpool ADG 4820 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Opvaskemaskine Whirlpool Manualer

Whirlpool

Whirlpool WDT751SAPZ Manual

28 Juli 2025
Whirlpool

Whirlpool W8I HT58 T Manual

28 Juli 2025
Whirlpool

Whirlpool WBC 3C34 PF X Manual

28 Juli 2025
Whirlpool

Whirlpool WFP 5O41 PLG X Manual

27 Juli 2025
Whirlpool

Whirlpool WSFE 2B19 Manual

27 Juli 2025
Whirlpool

Whirlpool WIS 7030 PEF Manual

27 Juli 2025
Whirlpool

Whirlpool WFO 3T142 X Manual

27 Juli 2025
Whirlpool

Whirlpool WIC 3C26 N Manual

27 Juli 2025
Whirlpool

Whirlpool WDF341PAPW Manual

27 Juli 2025
Whirlpool

Whirlpool W8I HP42 LSC Manual

27 Juli 2025

Opvaskemaskine Manualer

Nyeste Opvaskemaskine Manualer

Frigidaire

Frigidaire FDSH4502BF Manual

29 Juli 2025
Siemens

Siemens iQ300 SN43HS11TE Manual

28 Juli 2025
Blaupunkt

Blaupunkt 5VS401AU Manual

28 Juli 2025
GE

GE GDF540HSFSS Manual

28 Juli 2025
Neff

Neff S255HTX00E Manual

28 Juli 2025
Neff

Neff S287HDX01A Manual

28 Juli 2025
Blaupunkt

Blaupunkt 5VF421AU Manual

28 Juli 2025
GE

GE PDT760SSFSS Profile Manual

28 Juli 2025
GE

GE GDWF460VSS Manual

28 Juli 2025
Blaupunkt

Blaupunkt 5VI311AU Manual

28 Juli 2025