Whirlpool ADG 6600 IX Manual


Læs gratis den danske manual til Whirlpool ADG 6600 IX (8 sider) i kategorien Opvaskemaskiner. Denne vejledning er vurderet som hjælpsom af 22 personer og har en gennemsnitlig bedømmelse på 3.6 stjerner ud af 11.5 anmeldelser. Har du et spørgsmål om Whirlpool ADG 6600 IX, eller vil du spørge andre brugere om produktet?

Side 1/8
GB -1-
Chart
START/RESUME BUTTON
Push this button to start the selected program: the
indicator lights up and goes off at the end of the program.
When the door is opened during a washing cycle,
the cycle is temporarily paused: the Start indicator
blinks. To resume the cycle close the door and
push Start button again.
PROGRAM SELECTION
BUTTON
Push “Programs” button
(repeatedly) until the indicator
of the required program lights
up (see “Table of programs”
below).
CANCEL/OFF BUTTON
Push this button to switch off the control panel.
If pressed when a program is running it cancels the
program ongoing draining water for 1 minute.
If pressed when the dishwasher is switched off it
drains any possible liquids from dishwasher
(1 minute process).
If the indicator flashes repeatedly, see page 6 -
chapter ”What to do if ...”.
(see at right for options description)
1) Program data obtained in conformity with European standard EN 50242, obtained under normal conditions
(without additional options) and may vary depending on conditions. Differences of up to 20 minutes are possible
with sensor programs as a result of the appliance’s automatic calibration system.
2) Reference program for energy label in compliance with EN 50242 regulations. - Note for Testing Institutes: for
detailed information on the EN/Standard loading comparison test and other tests, contact the following address:
“nk_customer@whirlpool.com”.
Table of programs
Deter-
gent
Consumption
PPrograms Available
options Loading instructions Litres kWh Minutes 1)
1Pre-Wash cold Delay Crockery to be washed later. 5.0 0.02 10
2Glasses 40°C Delay Light soiling, for example
glasses and cups. X 13.0 0.90 97
3Quickwash 40°C Delay Lightly soiled crockery, with
no dried-on food. X 13.0 0.70 30
4Eco 2) 50°C Delay Normally soiled crockery.
Energy-saving program. X 15.0 1.05 165
5Intensive 70°C Delay
Recommended program for
heavily soiled crockery, especially
suitable for pans and saucepans.
X 15.0 1.50 140
5019 396 01960ADG 6600
BEFORE USING THE APPLIANCE FOR THE FIRST TIME CAREFULLY READ
THIS QUICK REFERENCE GUIDE AND THE ASSEMBLY INSTRUCTIONS!
Options and display description
SALT INDICATOR
When lit (at the end of the
cycle), the salt reservoir
needs to be refilled.
DELAYED START
BUTTON
The wash cycle can be
programmed to start
after 2, 4 or 8 hours.
Then press the Start
button. The wash
program will start after
the set time.
RINSE AID INDICATOR
When lit (at the end of the
cycle), the rinse aid
dispenser needs to be
refilled.
THE CONTROL PANEL OF THIS DISHWASHER ACTIVATES PUSHING
ANY BUTTON EXCEPT CANCEL/OFF BUTTON.
FOR ENERGY SAVING THE CONTROL PANEL DEACTIVATES
AUTOMATICALLY AFTER 30 SECONDS IF NO CYCLE HAS STARTED.
Quick reference guide
GB -2-
First time use
1- salt reservoir
2- rinse aid dispenser
3- detergent dispenser
4- racks system
5,6,7,8- available functions on the panel
9- filters
10- spray arms
1. Ask your water supply company what the water hardness is... 2. ...enter this value on
your dishwasher Suggestions for detergent use
German
degrees °dH
French
degrees °fH
English
degrees °eH
Water hardness
level
3 first PROGRAM LEDs
lit on the panel
(see table of programs)
P1 P2 P3
Gel or Powder
(rinse aid and
salt)
Tablets
0 - 5 0 - 9 0 - 6.3 Soft 1
go to step 1
(see “Daily
check”)
6 - 10 10 - 18 7 - 12.6 Medium 2
11 - 15 19 - 27 13.3 - 18.9 Average 3
16 - 21 28 - 37 19.6 - 25.9 Medium-hard 4 if water is
HARD extra salt
needs to be
added
(go to step 1,
“Daily check”)
22 - 28 38 - 50 26.6 - 35 Hard 5
29 - 35 51 - 63 35.7 - 44.1 Very hard 6
36 - 50 64 - 90 44.8 - 62.4 Extremely hard 7
Water hardness should be set only
before the first wash or if water
hardness has been changed
1Visual indicator
(depending
on the model).
Unscrew cap.
Fill the salt reservoir with water
before the first wash only.
(depending on the model)
The salt level indicator lamp may remain lit
at the end of several wash cycles. If the
water hardness level falls within category
(soft), no salt is required.
Salt indicator on the control panel Salt indicator on the salt reservoir cap
The indicator lamp lights up when SALT
NEEDS TO BE ADDED. green: OK. clear: NEEDS TO
BE ADDED
Daily check
Filling the salt reservoir - Dissolve limescale (not necessary if water hardness level is set to “soft”!)
- Press and hold together Programs and buttons for minimum 3 seconds.CANCEL/Off
- Programs LEDs will indicate the water hardness setting.
- Press the Programs button to increase setting (when the level reaches 7, the next key press will set the level back to 1.
- Wait 30 seconds (control panel switches off) or press START/Resume button to save setting.
Add salt (never add detergent!)
min. 0.8 kg / max. 1 kg
Water hardness level is factory
set for medium-hard water
(level 4).
Even if you use tablets which
include salt functionality, you
must still add regeneration salt
since such detergents are not
effective enough at softening
hard water.
Screw on the cap.
Salt residual
around the cap
need to be
removed. Some
salt reservoir have
a level indicator
integrated in the
cap (see below
how to check).
At first time use, the salt reservoir has to be filled independently from water hardness level (see description below in step 1 “Daily check”).
How to set water hardness in order to always assure the best cleaning results


Produkt Specifikationer

Mærke: Whirlpool
Kategori: Opvaskemaskiner
Model: ADG 6600 IX

Har du brug for hjælp?

Hvis du har brug for hjælp til Whirlpool ADG 6600 IX stil et spørgsmål nedenfor, og andre brugere vil svare dig