Whirlpool ADPU 7453 Manual

Whirlpool Opvaskemaskine ADPU 7453

Læs gratis den danske manual til Whirlpool ADPU 7453 (8 sider) i kategorien Opvaskemaskine. Denne vejledning er vurderet som hjælpsom af 13 personer og har en gennemsnitlig bedømmelse på 3.8 stjerner ud af 7 anmeldelser. Har du et spørgsmål om Whirlpool ADPU 7453, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/8

EN -1-

Chart

PROGRAMS SELECTION

BUTTON

Push “P” button (repeatedly)

until selected program number

is shown on the display

(P1...Px) - see “Table of

programs” below.

START/RESUME BUTTON

Push this button to start the selected program: the

indicator lights up and goes off at the end of the

program.

When the door is opened during a washing cycle,

the cycle is temporarily paused: the Start indicator

blinks. To resume the cycle close the door and

push Start button again.

CANCEL/OFF BUTTON

Push this button to switch off the control panel.

If pressed when a program is running it cancels the

program ongoing draining water for 1 minute

(0:01 is shown into the display).

If pressed when the dishwasher is switched off,

it drains any possible liquids from dishwasher

(1 minute process).

(see at right for options description)

1) Program data obtained in conformity with European standard EN 50242, obtained under normal conditions (without any options) and may vary depending on

conditions. Differences of up to 20 minutes are possible with sensor programs as a result of the appliance’s automatic calibration system.

2) Reference program for energy label in compliance with EN 50242 regulations. - Note for Testing Institutes: for detailed information on the

EN/Standard loading comparison test and other tests, contact the following address: “contact@whirlpool.com”.

3) The antibacterial action has been tested by the Institut Pasteur of Lille (France), based on the NF EN 13697 standard of November 2001.

*Power consumption in Left-on mode: 1.27 W / Off-mode: 0.40 W

Table of programs

Deter-

gent

Consumption

Drying

Phase

Programs Available

options Loading instructions Litres kWh Minutes 1)

P1 Sensor 40°-70°C Delay

Antibacterial

rinse

Recommended program for routine

washes, with dried-on food

(e.g. EN 50242). X7-15 1.00-1.70 70-172 Full

P2 Pre-Wash cold Delay Crockery to be washed later. —4.0 0.01 14-16 NO

P3 Rapid 45°C Delay Lightly soiled crockery, with no dried-

on food. X11.0 0.85 30-50 NO

P4 Eco 2) 50°C Delay

Antibacterial

rinse

Normally soiled crockery.

Standard Program, the most efficient

in terms of its combined energy and

water consumption.

X12.0 1.03 170 Full

P5 Fast Daily 60°C Delay

Antibacterial

rinse Normally to heavily soiled crockery. X11.0 1.30 80-95 Full

P6 Steam Delay

Antibacterial

rinse

Program including steam action

dedicated for heavily soiled crockery,

pots and pans. Soaking or hand

pretreatment is no longer needed.

X14.5 1.75 180-190 Full

5019 300 00744

BEFORE USING THE APPLIANCE FOR THE FIRST TIME CAREFULLY READ THIS

QUICK REFERENCE GUIDE AND THE ASSEMBLY INSTRUCTIONS!

Options and display description

SALT INDICATOR

When lit (at the end of the cycle),

the salt reservoir needs to be

refilled.

RINSE AID INDICATOR

When lit (at the end of the cycle),

the rinse aid dispenser needs to

be refilled.

WASH TIME DISPLAY

Indicated the cycle duration and the remaining time (h:min). With “Delayed start” selected it indicates

the time remaining until program start (h.00) - below 1h (0:min).

If “Fx Ey” messages appears on the display, see page 6 - chapter “What to do if...”.

THE CONTROL PANEL OF THIS DISHWASHER ACTIVATES PUSHING ANY

BUTTON EXCEPT CANCEL/OFF BUTTON.

FOR ENERGY SAVING THE CONTROL PANEL DEACTIVATES

AUTOMATICALLY AFTER 30 SECONDS IF NO CYCLE HAS STARTED.

DELAYED START BUTTON

Push the button

(repeatedly) to delay the

start of the program –

delay indicator turns on.

Adjustable from 1 to

24 hours. With each press

of the button, the delay

increases by one hour and

after "h 24" returns to

"h 00”. When this option

is selected the delay

indicator turns on. Then

press the START button.

The dishwasher will start

after the set time.

ANTIBACTERIAL RINSE 3)

This function activates an

antibacterial rinse at the end of

the wash cycle, guaranteeing a

further reduction of bacteria.

Press the button to activate

or deactivate the function.

This function can be used with

the programs indicated in

the table of programs.

The dishwasher door must

be kept shut for the entire

duration of the program in

order to guarantee reduction

of bacteria. If the door is

opened the indicator lamp

starts flashing.

TABLET SETTING

This setting allows to

optimize the cycle

performances according the

type of detergent used.

Push the Tablet button for

3 seconds (until the indicator

lights up) if you are using the

combined detergents in

tablet (rinse aid, salt and

detergent in 1 dose). If you

are using powder detergent

or liquid detergent, the

Tablet indicator on the

control panel has to be off.

Quick reference guide

Whirlpool is a registered trademark of Whirlpool USA

EN -2-

First time use

5 786

1- salt reservoir

2- rinse aid dispenser

3- detergent dispenser

4- racks system

5,6,7,8- available functions on the panel

9- filters

10- spray arms

Water hardness should be set only

before the first wash or if water

hardness has been changed

(depending on the model)

The salt level indicator lamp may remain lit

at the end of several wash cycles. If the

water hardness level falls within category

(soft), no salt is required.

Salt indicator on the control panel Salt indicator on the salt reservoir cap

The indicator lamp lights up when SALT

NEEDS TO BE ADDED. green: OK. clear: NEEDS TO

BE ADDED

- Press and hold together PROGRAM Selection and CANCEL/Off buttons for minimum 3 seconds.

- The current water hardness setting will be visible on the display.

- Press the PROGRAM Selection button to increase setting. Value range goes from 1 to 7 (when the level reaches 7, the next

press of the start button will set the level back to 1).

- Wait 30 seconds (control panel switches off) or press Start/Resume button to save setting.

1. Ask your water supply company what the water hardness is... 2. ...enter this value on

your dishwasher Suggestions for detergent use

German

degrees °dH French

degrees °fH English

degrees °eH Water hardness

level Insert value is shown

in the display Gel or Powder

(rinse aid and salt) Tablets

0 - 5 0 - 9 0 - 6.3 Soft 1

go to step 1

(see “Daily

check”)

6 - 10 10 - 18 7 - 12.6 Medium 2

11 - 15 19 - 27 13.3 - 18.9 Average 3

16 - 21 28 - 37 19.6 - 25.9 Medium-hard 4if water is

HARD extra salt

needs to be added

(go to step 1,

“Daily check”)

22 - 28 38 - 50 26.6 - 35 Hard 5

29 - 35 51 - 63 35.7 - 44.1 Very hard 6

36 - 50 64 - 90 44.8 - 62.4 Extremely hard 7

Water hardness level is factory

set for medium-hard water

(level 4).

Even if you use tablets which

include salt functionality, you

must still add regeneration salt

since such detergents are not

effective enough at softening

hard water.

At first time use, the salt

reservoir has to be filled

independently from water

hardness level (see description

below in step 1 “Daily check”).

1Visual indicator

(depending

on the model).

Unscrew cap.

Fill the salt reservoir with water

before the first wash only.

Daily check

Filling the salt reservoir - Dissolve limescale (not necessary if water hardness level is set to “soft”!)

Add salt (never add detergent!)

min. 0.8 kg / max. 1 kg

Screw on the cap.

Salt residual

around the cap

need to be

removed. Some

salt reservoir have

a level indicator

integrated in the

cap (see below

how to check).

Once regeneration salt is added, immediately start a wash program (the “Pre-wash” program alone is not sufficient).

Residual saline solution or grains of salt can lead to deep-down corrosion, irreparably damaging the stainless steel components.

The guarantee is not applicable if faults are caused by such circumstances.

How to set water hardness in order to always assure the best cleaning results

Produkt Specifikationer

Mærke:	Whirlpool
Kategori:	Opvaskemaskine
Model:	ADPU 7453

Har du brug for hjælp?

Hvis du har brug for hjælp til Whirlpool ADPU 7453 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Opvaskemaskine Whirlpool Manualer

Whirlpool WDT751SAPZ Manual

28 Juli 2025

Whirlpool W8I HT58 T Manual

28 Juli 2025

Whirlpool WBC 3C34 PF X Manual

28 Juli 2025

Whirlpool WFP 5O41 PLG X Manual

27 Juli 2025

Whirlpool WSFE 2B19 Manual

27 Juli 2025

Whirlpool WIS 7030 PEF Manual

27 Juli 2025

Whirlpool WFO 3T142 X Manual

27 Juli 2025

Whirlpool WIC 3C26 N Manual

27 Juli 2025

Whirlpool WDF341PAPW Manual

27 Juli 2025

Whirlpool W8I HP42 LSC Manual

27 Juli 2025

Opvaskemaskine Manualer

Nyeste Opvaskemaskine Manualer

Frigidaire FDSH4502BF Manual

29 Juli 2025

Siemens iQ300 SN43HS11TE Manual

28 Juli 2025

Blaupunkt 5VS401AU Manual

28 Juli 2025

GE GDF540HSFSS Manual

28 Juli 2025

Neff S255HTX00E Manual

28 Juli 2025

Neff S287HDX01A Manual

28 Juli 2025

Blaupunkt 5VF421AU Manual

28 Juli 2025

GE PDT760SSFSS Profile Manual

28 Juli 2025

GE GDWF460VSS Manual

28 Juli 2025

Blaupunkt 5VI311AU Manual

28 Juli 2025