Whirlpool WIS 9040 PEL Manual

Whirlpool Opvaskemaskiner WIS 9040 PEL

Læs gratis den danske manual til Whirlpool WIS 9040 PEL (33 sider) i kategorien Opvaskemaskiner. Denne vejledning er vurderet som hjælpsom af 18 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 9.5 anmeldelser. Har du et spørgsmål om Whirlpool WIS 9040 PEL, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/33

Before using the appliance carefully read Safety Instructions guide.

APPLIANCE

PRODUCT DESCRIPTION

1. ON/OFF button

2. PREVIOUS button

3. NEXT button

4. Multizone button

5. Display

6. Multizone indicator lights

7. Eco program indicator light

8. Start Delay indicator light

9. Program number and remaining time indicator

10. Closed water tap indicator light

11. Rinse Aid rell indicator light

12. Salt rell indicator light

13. Tablet Detergent (All-in-one) indicator light

14. Tablet Detergent (All-in-one) button with indicator light

15. Turbo button with indicator light

16. Power Clean® button with indicator light

17. Start Delay button with indicator light

18. START button with indicator light

CONTROL PANEL

0000 000 00000

Service:

1. Upper rack

2. Cutlery rack

3. Foldable aps

4. Upper rack height adjuster

5. Upper spray arm

6. Power Clean support

7. Lower rack

8. Lower spray arm

9. Filter Assembly

10. Salt reservoir

11. Detergent and Rinse Aid dispensers

12. Rating plate

13. Control panel

1 2 3 4 5 6 7 8 9 10 12 13 14 15 16 17 1811

INSTRUCTION FOR USE

THANK YOU FOR BUYING A WHIRLPOOL PRODUCT.

In order to receive a more complete assistance, please register your appliance on:

www.whirlpool.eu/register

FIRST TIME USE

SETTING MENU AND SALT

ADVICE REGARDING THE FIRST TIME USE

After installation, remove the stoppers from the racks and the retaining

elastic elements from the upper rack.

SETTING MENU

1. Switch on the appliance by pressing the button.ON/OFF

2. Switch o the appliance by pressing the button.ON/OFF

3. Hold down START button for 5 seconds, until you hear a beep.

4. The display shows the rst available setting (letter „A”), followed by

its value (for example: 3).

5. Press PREVIOUS/NEXT button to scroll the list of the available settin-

gs and to see their value (see the below table), then press START if you

want to change the value of the displayed setting: its value will start

blinking.

6. Use PREVIOUS/NEXT button to change the blinking value of the se-

lected settings, then press START to save the new value: it will stop

blinking.

7. To change another settings repeat steps 5-6.

8. To exit settings menu - press button. ON/OFF

LETTER SETTING VALUES

(Default - in bold)

Water Hardness Level

(see “SETTING THE WATER HARDNESS”

and “WATER HARDNESS TABLE”)

1 | 2 | | 4 | 53

Rinse Aid Level

(see “ADJUSTING THE DOSAGE OF

RINSE AID”)

1 | 2 | 3 | 4 | 5

Start Program

To set the cycle to show at switch on

of the appliance.

“E”= Eco, “L”= Last cycle run

E | L

Brightness Level

To adjust the brightness

level of the display.

“Lo”=Low, “Hi”= High

Lo | Hi

Sound Level

To adjust the volume of the sounds.

“OF” = sounds o, “Lo” = low volume,

“Hi” = high volume.

OF | Lo | Hi

Light on the Floor

(see OPTIONS AND FUNCTIONS)

“On” = On, “OF” = O

On | OF

Factory Settings

To restore to the factory default all

the values of the settings includ-

ed in the settings menu. After the

activation of this setting (ON), the

machine switches OFF and restores

the factory settings.

“On” = On, “OF” = O

On | OF

NaturalDry

(see “OPTIONS AND FUNCTIONS”)

“On” = On, “OF” = O

On | OF

FILLING THE SALT RESERVOIR

The use of salt prevents the formation of LIMESCALE on the dishes and

on the machine’s functional components.

• It is mandatory that THE SALT RESERVOIR NEVER BE EMPTY.

• It is important to set the water hardness.

The salt reservoir is located in the lower part of the dishwasher

(see PRODUCT DESCRIPTION) and must be lled when the SALT REFILL

indicator light in the control panel is lit.

1. Remove the lower rack and unscrew the

reservoir cap (anticlockwise).

2. Only the rst time you do this: ll the salt

reservoir with water.

3. Position the funnel (see gure) and ll the salt

reservoir right up to its edge (approximately

1 kg); it is not unusual for a little water to leak

out.

4. Remove the funnel and wipe any salt residue

away from the opening.

Make sure the cap is screwed on tightly, so that no detergent can get

into the container during the wash program (this could damage the

water softener beyond repair).

As soon as this procedure is complete, run a program without loading.

The “Pre-Wash” program alone is not sucient.

Residual saline solution or grains of salt can lead to corrosion, irreparably

damaging the stainless steel components.

The guarantee is not applicable if faults are caused by such circumstances.

After the salt has been poured into the machine, the SALT REFILL indi-

cator light switches o.

If the salt container is not lled, the water softener and the heating

element may be damaged as a result of limescale accumulation.

Using of Salt is recommended with any type of dishwasher detergent.

Whenever you need to add salt, it is mandatory to complete the pro-

cedure before the beginning of the washing cycle to avoid corrosion.

SETTING THE WATER HARDNESS

To allow the water softener to work in a perfect way, it is essential that

the water hardness setting is based on the actual water hardness in

your house. This information can be obtained from your local water

supplier.

The factory setting is “3” for average water hardness.

To change, follow instructions in section “SETTING MENU”.

Water Hardness Table

Level °dH

German degrees

°fH

French degrees

°Clark

English degrees

1 Soft 0 - 6 0 - 10 0 - 7

2 Medium 7 - 11 11 - 20 8 - 14

3 Average 12 - 16 21 - 29 15 - 20

4 Hard 17 - 34 30 - 60 21 - 42

5 Very hard 35 - 50 61 - 90 43 - 62

Produkt Specifikationer

Mærke:	Whirlpool
Kategori:	Opvaskemaskiner
Model:	WIS 9040 PEL
Vekselstrømsindgangsspænding:	220 - 240 V
Bredde:	598 mm
Dybde:	555 mm
Højde:	820 mm
Vægt:	35500 g
Kontroltype:	Berøring
Indbygget skærm:	Ja
Strøm:	10 A
Ledningslængde:	1.3 m
Pakkevægt:	37500 g
Strømforbrug (slukket):	0.5 W
Placering af apparat:	Fuldt indbygget
Installationsrum bredde:	600 mm
Installationsrum dybde:	560 mm
Installationsrum højde:	900 mm
Tilsluttet belastning:	1900 W
Støjniveau:	41 dB
Tilløbsslange, længde:	1.55 m
Antal vaskeprogrammer:	10
Forsinket start-timer:	Ja
Justerbare fødder:	Ja
Dør farve:	Rustfrit stål
Vandforbrug pr. cyklus:	9.5 L
Farve på kontrolpanel:	Black, Stainless steel
Antal kuverter:	14 kuverter
Cyklustid:	190 min.
Forsinket start (maks.):	24 t
Opvaskeprogrammer:	Eco 45°C, Glass/delicate, Hygiene, Intensive 65°C, Pre-wash, Quick, Self-Clean 65°C
Indikator for afspændingsmiddel:	Ja
Energiforbrug pr. cyklus:	0.748 kWh
Energieffektivitetsskala:	A til G
Glasbeskyttelse:	Ja
Indikator for resterende tid:	Ja
Installationsrum højde (min.):	820 mm
Udøsslange længde:	1.5 m
Produktstørrelse:	Fuld størrelse (60 cm)
Støjemissionsklasse:	B
Energieffektivitetsklasse:	C
Energiforbrug pr. 100 cyklusser:	75 kWh
Temperatur (maks):	65 °C
Saltindikator:	Ja
Øverste kurv indstillelig højde:	Ja
Lydalarm:	Ja
Maksimal varmtvandsforsyning temperatur:	60 °C
Ready-indikator:	Ja