Winland EnviroAlert EA-400 Manual

Winland Smart hjem EnviroAlert EA-400

Læs gratis den danske manual til Winland EnviroAlert EA-400 (4 sider) i kategorien Smart hjem. Denne vejledning er vurderet som hjælpsom af 32 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 16.5 anmeldelser. Har du et spørgsmål om Winland EnviroAlert EA-400, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

Q S GUICK TART UIDE

D-011-0099 Rev (0 /201 )F 7 5

ALWAYS TEST THE YSTEM S

Test the system to ensure proper operation prior to leaving the job site To test the system, either change the probe’s .

temperature so it exceeds your limits, or change the limits to simulate an alarm. If a delay has been programmed, take the

delay out, test the unit, and then put the delay back in.

FREEZER OOLER ONITORING/C M

Never install the EnviroAlert console in a cooler or freezer (condensing environment). Instead, use a remote probe (TEMP-L-S

or TEMP-L-W) and program your zone accordingly. Extend the length of probe wiring up to 1,000’ (304.8m) using 22-18 AWG

twisted pair.

AVOIDING ALSE LARMS ON A F A COOLER OR REEZER F

Both the EA200 and EA400 oﬀer an alarm delay from 0-120 minutes for each zone When a cooler or freezer door is opened, .

the temperature will rise and the probe will detect that rise. Freezers periodically need to enter a defrost cycle which may

also cause the temperature to rise above your limits. Set delays to avoid nuisance alarms under these normal circumstances.

We cannot advise you on what to set for delays or limits.

O -BN OARD TEMP ENSOR ONLY S (EA200 )

The EA200 has an on-board ambient temperature sensor and it is programmed on Zone 1.

More information and product manuals can be found at: www.winland.com

Tech Support 8:00am - 5:00pm Central Time

(800) 635-4269 • +1-507-625-7231 P

www.winland.com

STEP 1: CONNECT POWER AND PROBE(S)

Connect power to the PWR IN terminals, as shown in Figure 1. Be sure to observe proper polarity. Connect the probe(s) to the

zone(s) you intend to monitor. Extend the length of probe wiring up to 1,000’ (304.8m) using 22-18 AWG twisted pair.

EA200 NOTE: Zone 1 is dedicated for the on-board temperature sensor. Remote probes must be programmed on Zone 2.

There is only one input for a remote probe on the EA200 - this is Zone 2.

EA400 NOTE: The EA400 does not have an on-board temperature sensor and uses only remote probes.

STEP 2: UNLOCK CONSOLE FOR PROGRAMMING

To unlock the console, press and simultaneously release the ENTER and ALARM SILENCE buttons. The

“lock” icon should change to “unlocked”.

STEP 3: SET THE TIME AND DATE

Press the TIME/DATE button. Using either the INCREASE or DECREASE button, adjust the hours and then press the ENTER

button. Continue in this manner to set the minutes, AM/PM, year, month, and day. If power is lost, the time and date must

be reset.

STEP 4: PROGRAM THE ZONE(S)

1. Press the ZONE button. The active zone number will be ﬂashing.

2. Select the zone you wish to program using INCREASE or DECREASE and then press ENTER. The “no”

means “not operational” and indicates the zone is currently oﬀ. Any zone not programmed should

be set to “no” and therefore turned oﬀ.

3. Based on the chart (Figure 2), select the proper sensor type using INCREASE or DECREASE and press ENTER.

Figure 1 - EA200 and EA400 Wiring

POWER REQUIREMENTS:

EA200-12: 11 to 14 VDC @ 120mA 11 to 14 VDC @ 200mAEA400-12:

EA200-24: 23 to 26 VDC @ 120mA 23 to 26 VDC @ 200mAEA400-24:

AUX OUT

Zone 1

PWR IN

PWR OUT

Z one 2

REMOTE PROBE INPUT

ALARM OUTPUTS

(On-Board

Sensor)

Zone 2

(External

Probe)

EA200

AUX OUT

Zone 1

Z one 2

Z one 3

Z one 4

PWR IN

PWR OUT

Z one 1

Zone 2

Zone 3

Z one 4

REMOTE PROBE INPUTS

ALARM OUTPUTS

EA400

Lock Unlock

Produkt Specifikationer

Mærke:	Winland
Kategori:	Smart hjem
Model:	EnviroAlert EA-400
Type:	Indbygget
Bredde:	154.2 mm
Dybde:	31.8 mm
Højde:	120.7 mm
Vægt:	250 g
Produktfarve:	Hvid
Kontroltype:	Knapper
Indbygget skærm:	Ja
Skærmtype:	LCD
Skærm:	LCD
Forbindelsesteknologi:	Ledningsført
Certificering:	TUV, FCC, CE
Bæredygtighedscertifikater:	RoHS
Indgangsspænding:	14 V
Formål:	Indendørs
Sensortype:	Temperatur og luftfugtighedssensor
Indgangsstrøm:	0.2 A
Antal understøttede enheder:	5
Temperatur, måleenheder:	°C
Porte, antal:	9
Temperatur måleinterval:	-50 - 150 °C