Winland HA-III+ Manual

Winland Luftfugter HA-III+

Læs gratis den danske manual til Winland HA-III+ (4 sider) i kategorien Luftfugter. Denne vejledning er vurderet som hjælpsom af 23 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 12 anmeldelser. Har du et spørgsmål om Winland HA-III+, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

Electronic Humidity Sensor

D-011-0105 Rev (0 /201 )F 7 5

SPECIFICATIONS

Power Requirement

Sensing Element

Sensing Range

Accuracy

Response Time

Operating Temp

Weight

Dimensions

Mounting

Case Material

Warranty

12 VDC @ 10mA

Capacitive / IC

5% - 95% R.H.

±5% (10% - 90% RH @ 77° F [25° C])

TC < 12 minutes

32˚ to 122˚F (0˚ to 50˚C); non-condensing For use in

environments. NOT for coolers or freezers. Indoor use only.

5 oz (0.14 g)

3.25 x 1.5 x 1” (8.2 x 3.7 x 2.5 cm)

Surface mount

ABS

1 Year Limited

CONTENTS

This package contains:

• 1 HA-III+

• 2 Mounting Screws and 2 anchors

• 1 Installation/Operating Instructions Guide

HA-III+

Tech Support 8:00am - 5:00pm Central Time

(800) 635-4269 • +1-507-625-7231 P

www.winland.com

G I ENERAL NFORMATION

The Winland HA-III+ is a sensor used for monitoring remote locations for rising or falling rates of humidity. The HA-III+ is

designed and approved to be used with the EnviroAlert® family of monitoring devices including the EA200-12, EA400-12,

EA800, and EA800-ip. The HA-III+ may also be used with Winland legacy monitoring devices including the TA-2HLD,

TA-3HLD, UTA-1, DTA-4 and DPM-4.

The setup of high and low limits is done through the interface on the monitoring device you are connecting to.

Important Note: HA-III+ must not be used with monitoring devices that are powered with 24V AC/DC. When

used with Winland legacy monitoring devices such as UTA-1, TA-2HLD, TA-3HLD, DTA-4 or DPM-4, the monitoring devices

must be set to read Fahrenheit.

T O HEORY OF PERATION

The HA-III+ senses the ambient room humidity electronically using a capacitive sensing element. Humidity should be

expected to vary from room to room and from one area of a room to another. Ventilation and airﬂow will greatly aﬀect

relative humidity.

When programming the HA-III+ sensor on the monitoring device, the initial reading you receive should be considered a

base reading. Allow at least 30 minutes of operation for sensor to stabilize prior to setting your high and

low limits. It is necessary for the temperature of the sensor to stabilize before the readings are considered accurate.

The outputs of Winland’s electronic monitoring devices react within seconds of a limit being exceeded. A sudden burst

of humid air from a door opening or a ventilation system starting, could cause a brief change in the humidity reading.

To avoid false alarms, a time delay should be programmed into the EA200-12, EA400-12, EA800, and EA800-ip, UTA-1

or TA-2HLD. It is strongly recommended to utilize a time delay unless your application requires instant

notiﬁcation.

Installation

The HA-III+ sensor should be ﬂush mounted directly to a ﬂat surface like a wall. The sensor should be located in an area

free from drafts, heat sources, and direct sunlight. It is recommended that the sensor is mounted at a height of

4-5’ (1.2-1.5 m) from the ﬂoor.

To begin installation of the HA-III+, you must ﬁrst remove the cover. Do not use excessive force while removing the cover,

you may crack or break the plastic housing. Grasp the HA-III+ between your thumb and index ﬁngers along the long

slotted surfaces of the sensor with the Winland logo facing you. Using a ﬂat bladed screwdriver, insert tip of screwdriver

into pry slot and pry open top cover until it swings loose from the base (See Figure 1). Remove screwdriver from gently

pry slot, grasp cover beneath detached ﬂange and swing to the right until cover fully detaches.

F 1IGURE

Produkt Specifikationer

Mærke:	Winland
Kategori:	Luftfugter
Model:	HA-III+
Type:	Indbygget
Bredde:	76 mm
Dybde:	50.8 mm
Højde:	44.5 mm
Vægt:	14 g
Driftstemperatur (T-T):	0 - 66 °C
Materiale:	Acrylonitrilbutadienstyren
Forbindelsesteknologi:	Ledningsført
Certificering:	TUV, CE, FCC
Bæredygtighedscertifikater:	RoHS
Formål:	Indendørs
Sensortype:	Luftfugtighedssensor
Nøjagtighed:	5 %
Temperatur måleinterval:	- °C
Fugtighed måleinterval:	5 - 95 %