Winland Temp Alert TA-1 Manual

Winland Luftfugter Temp Alert TA-1

Læs gratis den danske manual til Winland Temp Alert TA-1 (4 sider) i kategorien Luftfugter. Denne vejledning er vurderet som hjælpsom af 36 personer og har en gennemsnitlig bedømmelse på 4.0 stjerner ud af 18.5 anmeldelser. Har du et spørgsmål om Winland Temp Alert TA-1, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

Powerless Temperature Monitoring with Single Output

SPECIFICATIONS

Power Requirement No power required to operate.

Operating Temperature 50 to 130° F (10 to 54° C); non-condensing environments only.Alarm Use:

Alarm contacts may not function outside of this range.

-30 to 130° F (-34 to 54° C); non-condensing environments only.Display Use:

Low Limit Adjust Range -30 to 120° F (-34 to 49° C)

High Limit Adjust Range -20 to 130° F (-29 to 54° C)

Temp Accuracy ±3°F (±1.7° C)

Temp Response Time TC = 14 minutes

Temp Sensing Element Bimetallic Coil

Outputs Gold plated N.O. dry contacts (Not for high voltage use.)

Contact Output Rating 50mA @ 12VDC

Weight 6.5 oz (.18 kg)

Dimensions 6.25 x 3.75 x 2” (15.9 x 9.5 x 5.1 cm)

Material ABS

Mounting Key slot

CONTENTS

This package contains:

• One (1) TA-1

• Two (2) mounting screws and two (2) wall anchors

• Mounting template (inside this Instruction Guide)

• One (1) Installation/Operating Instructions Guide

TA-1

D-011-0113 Rev B (08/2012)

Tech Support 8:00am - 5:00pm Central Time

(800) 635-4269 • +1-507-625-7231 P

www.winland.com

INTRODUCTION

The Temp˚Alert ® has been designed for reliable monitoring of non-condensing (indoor only) environment

areas where high and low temperature limits are critical.

Select an acceptable temperature range by setting the adjustable high and low limit arms. If the monitored are

temperature either rises or falls to the limit arms, the temperature indicator will contact one of the limit arms.

This completes the circuit and provides you with a dry contact alarm signal. The TA-1 contacts are normally

open (N.O.) dry contacts rated at 50mA at 12 VDC . This output can be used to activate alarm systems, telephone

dialers, or other remote warning devices. Temp˚Alert ® is the ideal addition for any security system.

LOCATION

In specifying the location and number of TA-1s to install consider room size, eﬀectiveness of the ventilation

system, and critical monitoring areas. If the building already has an energy management system, an easy rule

of thumb to follow is to install a TA-1 near each thermostat. It should be mounted on a wall or other vertical

surface in the area where temperature is to be monitored. Make sure it is well clear of windows, doors, or heat

sources that could cause an inaccurate reading of air temperature. When protecting a building against freeze

damage, always install at least one Temp˚Alert ® on every level of the home or business.

INSTALLATION

Items needed:

· Standard screwdriver · 11/32” wrench · 22-18 AWG twisted pair

STEP 1 – A TA-1 M STTACH TO OUNTING URFACE

Position the mounting template in the desired location and mark the mounting holes. Depending on the type

of surface you are mounting to, you may need to predrill holes to accept the mounting screws alone, or use the

plastic anchors and mounting screws. Drive the screws into the mounting surface, allowing approximately 3/16”

between the screw head and the mounting surface. (See Mounting Template below.) Engage the key slots on

the back of the TA-1 case with the screw heads and press down.

To insure proper operation, test weekly.

M TOUNTING EMPLATE

Produkt Specifikationer

Mærke:	Winland
Kategori:	Luftfugter
Model:	Temp Alert TA-1
Type:	Fritstående
Bredde:	159 mm
Dybde:	95 mm
Højde:	51 mm
Vægt:	170 g
Forbindelsesteknologi:	Ledningsført
Formål:	Indendørs
Sensortype:	Temperatursensor
Nøjagtighed:	1.7 °C
Temperatur måleinterval:	-34 - 54 °C