Winland WB-200 Manual

Winland Detektor WB-200

Læs gratis den danske manual til Winland WB-200 (4 sider) i kategorien Detektor. Denne vejledning er vurderet som hjælpsom af 46 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 23.5 anmeldelser. Har du et spørgsmål om Winland WB-200, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

Electronic Water Detection Device

D-011-0116 Rev C (08/2012)

SPECIFICATIONS

Power Requirement 8-28 VDC @ 35mA

8-28 VAC @ 100mA

Sensitivity Will not alarm due to high humidity or condensation.

Operating Temp 32˚ to 130˚F (0˚ to 54˚C); non-condensing environment (indoor use only)

Output 1 Form C Relay (N.O./N.C.)

1 Amp @ 30 VDC, resistive

1 Amp @ 24 VAC, resistive

Probe Options Includes 1 Standard Unsupervised Surface Probe (W-S-U)

Accepts up to 6 Unsupervised Surface Probes (W-S-U) wired in parallel or

Accepts up to 6 Unsupervised Under Carpet Probes (W-UC-U) wired in parallel.

Max Cable Length 1-2 probes; max recommended distance of 200’ (61 m)

3-6 probes; max recommended distance of 100’ (30.5 m)

Probe Cable Probes include 15' (4.6 m) cable. Extend using 22-18 AWG twisted pair.

Console Weight 2.4 oz (0.07 kg)

Console Dimensions 4.1 x 2.36 x 1.18” (10 x 6 x 3 cm) with ﬂanges

Probe Dimensions Surface: 2 x 3 x 0.88” (5.1 x 7.6 x 2.2 cm)

Under Carpet: 2 x 3 x 0.18” (5.1 x 7.6 x 0.5 cm)

Mounting Flanges

Case Material ABS

Warranty 1 Year Limited

CONTENTS

This package contains:

• 1 WB-200

• 1 Surface Probe - Unsupervised (W-S-U)

• 1 Installation/Operating Instructions Guide

WB-200

Tech Support 8:00am - 5:00pm Central Time

(800) 635-4269 • +1-507-625-7231 P

www.winland.com

INTRODUCTION

Thank you for your purchase of the Winland WaterBug® model WB-200. The WB-200 is completely electronic and is designed

to detect water only (distilled and deionized water cannot be detected). The WB-200 is not a self contained warning device.

For proper operation, it must be used in conjunction with an alarm system, sounder, etc. It is designed so that the control

console mounts on a wall or other ﬂat vertical surface and the remote probes are placed in the locations where water

leakage is most probable. Up to six remote probes may be connected to one control console. A ﬁlm of moisture forming a

bridge between the two metallic contacts on any remote probe is all that is needed for the unit to signal an alarm condition.

The output on the WB-200 is non-latching, but will remain in alarm state until the moisture bridge is broken. As sensitive

as the WB-200 is, it will not alarm due to high humidity or condensation. The WB-200 is ideal for use in homes, oﬃces,

computer rooms, warehouses, etc.

INSTALLATION

Locate the area where the WB-200 console is to be mounted. Using the WB-200 as a guide, mark the two locations on the

mounting surface where the holes will be drilled in order to use the case’s mounting ﬂanges. If mounting on drywall, use the

two provided drywall anchors. Once the holes have been drilled, place the WB-200 against the surface and drive the screws

into the holes or anchors.

Multiple probes must be hooked up in parallel to the two “sensor” terminals. The remote surface probes may be mounted

securely to the ﬂoor or a wall. Mounting the probe(s) to a vertical surface like a wall enables you to monitor an area for rising

water levels. This is useful in basement sump pumps and other types of water storage and drainage systems.

TERMINAL LOCK ONNECTIONS B C

Relay contacts are accessible on the terminal block (See

Figure 1). The WB-200 is in normal condition when

power is applied and no moisture is being detected. It’s

in alarm condition when water is detected by any one

of the remote probes.

Note: When connecting DC power to the WB-200 be

sure to observe polarity and test to see if the WB-200

is operating properly. This may be done by forming

a water bridge between two of the metallic contacts

located on the probe (See Figure 2) with a moistened

ﬁnger or cloth. If the WB-200 is not operating properly,

check the polarity of the power supply connections.

AC – Power input wires are interchangeable

DC – Positive to V+ and negative to Ground

VAC / +VDC

Relay Common

Relay N.O.

Relay N.C.

Ground (VAC / -VDC)

Figure 1

Produkt Specifikationer

Mærke:	Winland
Kategori:	Detektor
Model:	WB-200
Vekselstrømsindgangsspænding:	8 - 28 V
Bredde:	100 mm
Dybde:	60 mm
Højde:	30 mm
Produktfarve:	Hvid
Produkttype:	Sensmitter
Driftstemperatur (T-T):	0 - 54 °C
Forbindelsesteknologi:	Ledningsført
Strømkilde type:	Vekselstrøm
Transmissionsafstand:	61 m
Nominel udgangsstrøm:	1 A