WyreStorm MX-0404-HDBT-H2A-KIT Manual

WyreStorm Hi-Fi system MX-0404-HDBT-H2A-KIT

Læs gratis den danske manual til WyreStorm MX-0404-HDBT-H2A-KIT (4 sider) i kategorien Hi-Fi system. Denne vejledning er vurderet som hjælpsom af 6 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 3.5 anmeldelser. Har du et spørgsmål om WyreStorm MX-0404-HDBT-H2A-KIT, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

4x4 4K UHD HDBaseT (35m/115ft) Matrix with audio breakout,

HDCP 2.2 and PoH Receivers

MX-0404-HDBT-H2A-KIT Quickstart Guide

IMPORTANT! Installation Requirements

• Visit the product page to download the latest rmware, document

version, additional documentation, and conguration tools.

• Install the latest rmware (if available) to ensure that all features

described in this document are available during and after installation.

• Read through the Wiring and Connections section for important wiring

guidelines before creating or choosing premade cables.

In the Box

1 x MX-0404-HDBT-H2A-KIT HDBaseT Matrix Switcher

4 x HDBaseT PoC display receivers

1 x Handheld IR Remote (CR2025 Battery not Included)

4 x IR emitters

4 x IR Broadband Receiver (30KHz to 50KHz)

1 x IR Extension Cable

1x AC Power Cord with US Plug

1x AC Power Cord with UK Plug

1x AC Power Cord with EU Plug

2x Mounting Brackets and accessories (matrix)

1x Quickstart Guide (this document)

Basic Wiring Diagram

MX-0404-HDBT-H2A-KIT Quickstart Guide | 200205

UK: +44 (0) 1793 230 343 | ROW: 844.280.WYRE (9973)

support@wyrestorm.com

1 of 4

WyreStorm recommends reading through this document in its entirety to become familiar with the product’s features prior to starting the installation

process.

Wiring and Connections

WyreStorm recommends that all wiring for the installation is run and terminated prior to making connections to the switcher. Read through this section in this

entirety before running or terminating the wires to ensure proper operation and to avoid damaging equipment.

HDMI/HDBaseT Wiring

IMPORTANT! Wiring Guidelines

• The use of patch panels, wall plates, cable extenders, kinks in cables, and

electrical or environmental interference will have an adverse effect on HDMI

and Ethernet transmission limiting performance. Steps should be taken to

minimize or remove these factors completely during installation for best

results.

• WyreStorm recommends using high quality HDMI cables such as

WyreStorm Express to ensure the highest content performance available.

• The type of category cable and length used can restrict the available video

resolution. While Cat5e can be used, WyreStorm recommends using Cat6

or higher to ensure the highest content performance available. See Video

Resolutions in the Specications table before determining cable type and

length.

Pin 1

Pin 8

Wire colors shown follow EIA/TIA-568B standard.

Pin 1:

Pin 2:

Pin 3:

Pin 4:

Pin 5:

Pin 6:

Pin 7:

Pin 8:

White/Orange

Orange

White/Green

Blue

White/Blue

Green

White/Brown

Brown

IR TX/RX Wiring

IMPORTANT! IR TX/RX Guidelines

• WyreStorm IR ports function differently than standard IR ports. For this

reason only WyreStorm IR emitters and receivers can be used.

• WyreStorm IR emitter and receiver cables cannot be spliced as cutting

into the cables will short the shield. While an extension cable may be used,

WyreStorm assumes no responsibility for operation using an extension

cable.

• When connecting the IR TX to an IR connecting blocks or control system

with different plugs, a cable must be made following the IR TX Port Pinout

diagram.

• When connecting to an IR control system use the WyreStorm CAB-IR-LINK

cable. This cable compensates for differences between the WyreStorm RX

and the control systems TX connection. Visit the CAB-IR-LINK product page

for details.

IR TX Port Pinout

Tip: Anode

Sleeve: Cathode (IR Signal)

IR RX/Ext Port Pinout

Tip:

Ring: IR Signal

+5V DC

Sleeve: Ground (GND)

RS-232 Wiring

Most control systems and computers are DTE where pin 2 is RX, this can vary

from device to device. Refer to the documentation for the connected device for

pin functionally to ensure that the correct connections can be made. 5

9 8 7 6

4 13 2

Outside of DB9 chassis port shown.

Unidnetiﬁed pins have no function and should

not be connected.

Pin 3: RX (Receive)

Pin 2: TX (Transmit)

Pin 5: GND (Ground)

MX-0404-HDBT-H2A-KIT Quickstart Guide | 200205

UK: +44 (0) 1793 230 343 | ROW: 844.280.WYRE (9973)

support@wyrestorm.com

2 of 4

Produkt Specifikationer

Mærke:	WyreStorm
Kategori:	Hi-Fi system
Model:	MX-0404-HDBT-H2A-KIT

Har du brug for hjælp?

Hvis du har brug for hjælp til WyreStorm MX-0404-HDBT-H2A-KIT stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Hi-Fi system WyreStorm Manualer

WyreStorm MX-0606-PP-POH Manual

27 August 2024

WyreStorm MX-0404-HDBT-H2A-KIT Manual

27 August 2024

WyreStorm SW-0501-HDBT Manual

27 August 2024

Hi-Fi system Manualer

Nyeste Hi-Fi system Manualer

DPA d:vice MMA-A Manual

1 August 2025

Muse M-610 SH Manual

31 Juli 2025

Pro-Ject Head Box E Manual

30 Juli 2025

Pro-Ject Uni Box S3 Manual

30 Juli 2025

Hamilton Buhl PA-25 Manual

30 Juli 2025

SSL SQ4 Manual

29 Juli 2025

SSL ML46DB Manual

29 Juli 2025

SSL ML39USA Manual

29 Juli 2025

SSL Evolution EV2.200 Manual

29 Juli 2025

SSL Evolution EV4.400 Manual

29 Juli 2025