Xantech J-BOX BLAST-IR Manual

Xantech Blitz J-BOX BLAST-IR

Læs gratis den danske manual til Xantech J-BOX BLAST-IR (4 sider) i kategorien Blitz. Denne vejledning er vurderet som hjælpsom af 15 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 8 anmeldelser. Har du et spørgsmål om Xantech J-BOX BLAST-IR, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

- 1 -

INSTALLATION INSTRUCTIONS

380-20

Single Gang, J-BOX, BLAST-IR™ Emitter

DESCRIPTION

The 380-20 J-BOX BLAST-IR™ contains three high-intensity Infrared LEDs housed in a metal

enclosure that can easily be mounted inside a standard, single gang, J-BOX electrical receptacle.

The benefit of the 380-20 is that it can “flood” an enclosed area with an infrared signal. The 380-20

comes with mounting screws and a Decora® style insert that can be used with the popular Decora®

faceplate.

SPECIFICATIONS

 +12VDC, 200mA.

 Red IR talk-back LED (internal).

 Dimensions: 1-3/4” W x 4” H x 1-1/4” D.

 Recommended wire requirements: 3 or 4 conductor, 22 gauge solid or stranded wire up to

600 feet (unshielded OK).

 Able to achieve a distance well over 30 feet.

Breakawa

plaster-ears

Red IR talk-back LED

6-32 Threaded hole

(

)

for

Decora® -style cover plate

J-Box mountin

hole

(

)

4-Pin matin

plu

(included)

h-intensit

infrared LED

Decora

Insert with dark

tinted lens cover

(included)

Decora

faceplate

(not included)

- 2 -

INSTALLATION

The 380-20 is intended to be wired to the terminals of any Xantech connecting block such as the

CB12 and 789-44. Use 3 or 4 conductor cable, as specific above, to run between the connecting

block and the 380-20. The conductor cable will be used to connect the +12VDC, IR BUS, and

GROUND terminals.

While it is possible to make wired connections without a Xantech connecting block, it is not

recommended. The Xantech connecting block reduces installation time, helps to eliminate errors,

allows easy troubleshooting, and permits easy system upgrades later, if needed.

Connecting the power supply to the connecting block must be the last step. Be sure to verify all wires

are connected to the correct terminals. Incorrect connections may destroy the product. Two 380-20’s

may be connected in parallel.

Figure 1: 380-20 Basic IR Repeater System. 380-20 IR Repeater System.Figure 2:

NOTE: The 380-20 infrared intensity is so great that it is possible to place the unit in an indirect view

of the components to be controlled. This is due to the infrared waves “bouncing” off a wall and/or

object. An ideal location would be an enclosed closet where the system components are stored. It is

strongly recommended to experiment with the 380-20’s exact location before installing the single

gang box, J-Box, receptacle.

The three high-intensity infrared LEDs (light-blue) located on the front of the product are not visible to

the human eye. The red talk-back LED indicates the 380-20 is receiving an IR signal at the input.

Produkt Specifikationer

Mærke:	Xantech
Kategori:	Blitz
Model:	J-BOX BLAST-IR

Har du brug for hjælp?

Hvis du har brug for hjælp til Xantech J-BOX BLAST-IR stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Blitz Xantech Manualer

Xantech 283TPD Manual

29 August 2024

Xantech J-BOX BLAST-IR Manual

28 August 2024

Blitz Manualer

Nyeste Blitz Manualer

Neewer RF1-N Manual

29 Marts 2025

Neewer RF1-S Manual

29 Marts 2025

Bresser BRM-300AM Manual

27 Marts 2025

Rollei Studio 300 Manual

9 Marts 2025

SmallRig 4774 Manual

26 Februar 2025

Smith-Victor Orbit Pro Manual

24 Februar 2025

Pelican MityLite 1900 Manual

28 Januar 2025

Neewer NW665 Manual

8 Januar 2025

Godox V100 S Manual

8 Januar 2025

Godox V100 O Manual

8 Januar 2025