Xvive AT-1 Manual

Xvive Ikke kategoriseret AT-1

Læs gratis den danske manual til Xvive AT-1 (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 6 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 3.5 anmeldelser. Har du et spørgsmål om Xvive AT-1, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

· Signal Generator:

Outputs a 1 kHz sine wave or pink

noise audio signal through XLR male,

1/4", and 1/8" connectors, with three

output level options: -10 dB, -20 dB,

and -40 dB.

· XLR Cable Tester:

Tests whether all three pins of the XLR

cable are functioning properly.

· Phantom Power Check:

Tests the output voltage of the phantom

power and ensures both pins are

functioning properly.

· XLR Input Metering:

Measures the input volume level of

the XLR female connector.

· Headphone and Speaker Monitoring:

When an audio source is connected to the XLR female / 1/4" input, you can

monitor the signal with headphones or speakers via the 1/8" headphone jack.

SPECIFICATIONS

You can use sine waves and pink noise to test the audio inputs of all kinds

of audio gear—including DI boxes, guitar pedals, wireless systems, eect

units, active speakers, mixers, etc.

Checks for phantom power

voltage, which is individually

metered on pins 2 and 3 of

the output XLR. If the voltage

detected is between 24V

and 44V, the LEDs will ash

slowly.

Activating phantom power

on the input channel you are

checking will allow you to

simultaneous test all three

pins in the XLR line.

SIGNAL GENERATOR 1 KHZ SINE WAVE AND PINK NOISE

Audio inputs are ¼” TS and XLR, and the 1/8” output can go to headphones

or a speaker.

The volume knob controls the output volume. When anything is connected

to the 1/8” output jack, the speaker is muted.

Regardless of the routing mode, as long as there is a 1/4" audio signal input,

it will be directly sent to both the speaker and the headphone output.

If you need to monitor the signal more accurately, plug your headphones

into the headphone jack and adjust the level using the volume knob on the

side of the unit.

Charge your AT-1 using a standard USB-C cable and any 5V/2A USB power

supply. A full charge cycle takes about one hour and the device can be

used while charging.

The LED by the USB-C port lights up while the battery is charging, and

turns o when the battery is fully charged.

Always power down your AT-1 after use. Depleting the battery may cause

irreversible damage, resulting in the device being unable to power on

again.

SPEAKER/HEADPHONE OUTPUT

The function LED (11) next to the SEL button will

blink white as a warning when the battery is:

• Low: 3 white blinks

• Out of charge: 6 white blinks

Consider recharging your AT-1 when the rst

‘low battery’ warnings appear.

BATTERY

CHARGING

ALERT

XLR INPUT METERING

XLR CABLE TESTER

PHANTOM POWER CHECK AND XLR PIN CHECK

48V

OUTPUT

Yellow LED: signal output via XLR

Blue LED: signal output via 6.35 mm (1/4”) TS

or 3.5 mm (1/8”) TS

TYPE

OUTPUT LEVEL

10 dB, 40 dB, 20 dB

Solid LED: pink noise

Flashing LED: 1 kHz sine wave

The PK (peak) and SG (signal) LEDs will

illuminate according to the RMS

amplitude of the signal present on the

input XLR. The SG LED is lit when the

signal exceeds -20 dBu RMS, and the

PK LED lights up when the signal

exceeds +10 dBu.

‘SG’ lights up when signal is detected.

‘PK’ lights up when the signal is very

loud. This feature is very useful in noisy

environments, or if you can’t get your

ears close enough to the speaker.

Connect an XLR cable to the input and output to test its 3 pins.

Hold SEL for 2s to enter XLR cable test mode. The LED will automatically

cycle through the pins.

Press SEL to stop the cycle and manually select a pin.

Press TO to resume the automatic cycle.

1 1

2 2

Line ok

Pin2 defective

XLR line

Solid LED: Line ok

Phantom power voltage: 44-52V

pin 1 defective

pin 2 defective

pin 3 defective

Flashing LED: Line ok

Phantom power voltage: 24-44V

_ 01

_ _ 02 _ _ 03 _ _ 04 _ _ 05 _ _ 06 _

English Manual

www.xvive.com

PORTABLE

AUDIO TESTER

AT-1

1. XLR-M output

2. XLR-F input

3. 1/4” output/input

4. 1/8” output

5. Speaker/headphone output

volume knob

6. Speaker

7. USB type-C charging input

8. Power and Charging LED

9. Phantom power pin voltage check

10. Output select: XLR, 6.35 mm

(1/4”)/3.5 mm (1/8”) or speaker

11. Output signal generator Type select:

1 kHz sine wave or pink noise.

Hold 3s for XLR cable tester

12. Output mode / battery life LED

13. Output volume (pad) select

14. Input volume check LED

15. XLR cable test LED

16. Power on/o

48V

ROUTE

XLR

OUTPUT

-5

-10

-20

-30

-40

-50

-60

-∞

+10

PHA NTOM

POW ER

IN P U T LEVEL

PHA NTOM

POW ER

INP UT L EV EL

1/4“ or XLRF input

Headphone or

speaker output

PHA NTOM

POWER

INP UT LEVE L

1/4“ or XLR-F input

Headphone or speaker output

This versatile and compact utility tool includes detection features and oers ve

main functions: a Signal Generator that can emit 1kHz tones or pink noise audio

signals, an XLR Cable Tester for detecting whether XLR cables are damaged, XLR

Input Metering to measure the strength of XLR input signals, a Phantom Power

Check to test voltage and ensure normal operation, and Headphone and

Speaker Monitoring to listen to input signals. It is suitable for testing powered

PA speakers, eect pedals, cables, DI boxes, IEM systems, mixers, and other

audio equipment, making it an essential tool for audio professionals.

Produkt Specifikationer

Mærke:	Xvive
Kategori:	Ikke kategoriseret
Model:	AT-1

Har du brug for hjælp?

Hvis du har brug for hjælp til Xvive AT-1 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Xvive Manualer

23 December 2025

23 December 2025

3 Juli 2025

3 Juli 2025

27 Juni 2025

26 Juni 2025

25 Juni 2025

30 Januar 2025

Xvive More You Manual

30 Januar 2025

Xvive A58 Manual

6 September 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

KoolStar Starter 950 Manual

25 December 2025

VOX SETSF5702B Manual

25 December 2025

Yamazen SUC-202 Manual

25 December 2025

Vaxcel OW37081 Manual

25 December 2025

Vaxcel T0253 Manual

25 December 2025

Reelcraft L 4525 123 7A Manual

25 December 2025

Reelcraft L 5700 Manual

25 December 2025

Viewsonic ViewBoard IN8621C Manual

25 December 2025

Yamazen YTY-A410 Manual

25 December 2025

BlaknBlu Oscar DSF Manual

25 December 2025