Yakima HoldUp +2 Manual

Yakima Cykelholder HoldUp +2

Læs gratis den danske manual til Yakima HoldUp +2 (21 sider) i kategorien Cykelholder. Denne vejledning er vurderet som hjælpsom af 38 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 19.5 anmeldelser. Har du et spørgsmål om Yakima HoldUp +2, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/21
1034431G-1/21
IMPORTANT WARNING
IT IS CRITICAL THAT ALL YAKIMA RACKS AND ACCESSORIES BE PROPERLY AND SECURELY ATTACHED TO YOUR VEHICLE. IMPROPER
ATTACHMENT COULD RESULT IN AN AUTOMOBILE ACCIDENT, AND COULD CAUSE SERIOUS BODILY INJURY OR DEATH TO YOU OR
TO OTHERS. YOU ARE RESPONSIBLE FOR SECURING THE RACKS AND ACCESSORIES TO YOUR CAR, CHECKING THE ATTACHMENTS
PRIOR TO USE, AND PERIODICALLY INSPECTING THE PRODUCTS FOR ADJUSTMENT, WEAR, AND DAMAGE. THEREFORE, YOU
MUST READ AND UNDERSTAND ALL OF THE INSTRUCTIONS AND CAUTIONS SUPPLIED WITH YOUR YAKIMA PRODUCT PRIOR TO INSTALLATION
OR USE. IF YOU DO NOT UNDERSTAND ALL OF THE INSTRUCTIONS AND CAUTIONS, OR IF YOU HAVE NO MECHANICAL EXPERIENCE AND ARE NOT
THOROUGHLY FAMILIAR WITH THE INSTALLATION PROCEDURES, YOU SHOULD HAVE THE PRODUCT INSTALLED BY A PROFESSIONAL INSTALLER.
SAFETY CLIP (1X)
BASE (1X)
WRENCH (1X)
REAR WHEEL TRAY
ASSEMBLY (1X)
FRONT WHEEL TRAY
ASSEMBLY (1X)
BOLT (1X)
LOCK WASHER (1X)
INsTAll ThIs
PROducT ON 2"
hITch veRsION Of
The hOlduP
PIN (1X)
PLUG (1X)
KEY (2X)
For Your
Safety
Warranty
Registration
on-line
YAKIMA.com
Safety Kit included:
See additional
instructions for
installation.
HEX WRENCH (1X)
1034431G-2/21
ReMOve eNd cAP
fROM hOlduP.
Using a flathead screwdriver, remove
the end cap from the HoldUp.
INseRT Plus2 BAse INTO hOlduP.
Insert the Plus2
base into the
HoldUp tube,
aligning holes.
Align
INsTAll MAIN BOlT.
• Insert bolt,
and lock-
washer in
order shown.
• Tighten with
adjustable
wrench.
ROTATe TO uPRIGhT POsITION.
• Squeeze knob to release lock.
• Pull spring pin to release base.
• Lift frame.
• Release spring pin. Pin should snap into place
and lock.
75 ft-lbs.
ReMOve fAsTeNeRs.
The fasteners are installed in the trays for shipping
purposes. Remove them to prepare for assembly.

Produkt Specifikationer

Mærke: Yakima
Kategori: Cykelholder
Model: HoldUp +2

Har du brug for hjælp?

Hvis du har brug for hjælp til Yakima HoldUp +2 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Cykelholder Yakima Manualer

Yakima

Yakima HoldUp +2 Manual

3 Oktober 2024
Yakima

Yakima JustClick 2 Manual

18 September 2024
Yakima

Yakima RidgeBack 5 Manual

10 August 2024
Yakima

Yakima FullSwing Manual

9 August 2024
Yakima

Yakima HoldUp EVO +2 Manual

3 August 2024
Yakima

Yakima RaptorAero Manual

2 August 2024
Yakima

Yakima RidgeBack 4 Manual

31 Juli 2024
Yakima

Yakima HighRoad Manual

31 Juli 2024
Yakima

Yakima HighSpeed Manual

30 Juli 2024
Yakima

Yakima HalfBack 3 Manual

27 Juli 2024

Cykelholder Manualer

Nyeste Cykelholder Manualer

Uebler

Uebler i21 Z90 Manual

18 September 2025
Uebler

Uebler i21 Z60-DC Manual

18 September 2025
Uebler

Uebler F34 Manual

18 September 2025
Uebler

Uebler i31 Z-DC Manual

18 September 2025
Uebler

Uebler X31S Manual

18 September 2025
Uebler

Uebler X21 S Manual

18 September 2025
Uebler

Uebler i41 S-DC Manual

18 September 2025
Uebler

Uebler i41 S Manual

18 September 2025
Uebler

Uebler P32-S Manual

18 September 2025
Uebler

Uebler i31 Z Manual

18 September 2025