Yamaha NS-U50 Manual

Yamaha Højttalersystem NS-U50

Læs gratis den danske manual til Yamaha NS-U50 (1 sider) i kategorien Højttalersystem. Denne vejledning er vurderet som hjælpsom af 31 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 16 anmeldelser. Har du et spørgsmål om Yamaha NS-U50, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/1

PRECAUTIONS

Read these precautions carefully before using your speaker.

• Any time you note distortion, reduce the volume control on

your amplifier to a lower setting. Never allow your amplifier

to be driven into “clipping”. Otherwise the speaker may be

damaged.

• When using an amplifier with a rated output power higher

than the nominal input power of the speaker, care should

be taken never to exceed the speaker’s maximum input.

• Do not attempt to clean the speaker with chemical

solvents as this might damage the finish. To clean, wipe

with a dry, soft cloth.

• To prevent the enclosure from warping or discoloring, do

not place the speaker where it will be exposed to direct

sunlight or excessive humidity.

• Do not place the speaker where it is liable to be knocked

over or struck by falling objects. Stable placement will also

ensure better sound performance.

• Placing the speaker on the same shelf or rack as the

turntable can result in feedback.

• This speaker system is designed for home use only. Never

use this speaker system inside a car.

• Secure placement or installation is the owner’s

responsibility.

YAMAHA shall not be liable for any accident caused

by improper placement or installation of the speaker.

ATTACHING STAND

Attach the included stands to the

speakers using the two included

screws. Place the speakers next

to a personal computer on a

desktop to achieve the optimum

listening position. Be sure to

attach the stands to the speakers

correctly as shown in the figure.

If you attach them in the opposite

direction or otherwise incorrectly,

the speakers may fall and be

damaged or cause injury.

■Non skid pad

To prevent the speakers from sliding around, attach the

supplied pads as shown in the illustration.

You can also use the screw holes on the rear of the speaker

for installing the speakers.

60 mm A screw with a diameter of 4 mm and a

pitch of 0.7 mm can be used.

(Depth of hole: 8 mm)

NS-U50

CONNECTION TO YOUR AMPLIFIER

BEFORE MAKING CONNECTIONS, MAKE SURE THAT

THE AMPLIFIER IS SWITCHED OFF.

■CONNECTIONS

• Connect the push-type input terminals at the rear of the

speakers to the speaker output terminals of your amplifier

with the provided speaker cord.

• One side of the speaker cord is marked by a red line.

Connect the (+) terminals on both the amplifier and the

speakers using this red-marked side. Connect the (–)

terminals on both components using the black-side of the

cord.

• Connect one speaker to the left (marked L) terminals of

your amplifier, and another speaker to the right (marked R)

terminals, making sure not to reverse the polarity (+, –). If

one speaker is connected with reversed polarity, the sound

will be unnatural and lack bass.

Procedures:

1Press the tab on the terminal down, as shown in the

figure.

2Insert the bare speaker wire end properly into the terminal

hole. [Remove approx. 5 mm (1/4") insulation from the

speaker cord.]

3Remove your finger from the tab to allow it to lock snugly

on the cord’s wire end.

4Test the security of the connection by tugging lightly on the

cord at the terminal.

ANALOG

PC IN

AUX 1

SUB

WOOFER

OUT

AUX 2

R L

ANTENNA

75 Ω

UNBAL

GND

DIGITAL

SPEAKERS

6Ω MIN./SPEAKER

–

USB

OPT OUT

AUX 1

OPT IN

COAX IN

OPT IN

R L

SPEAKERS

6 MIN./SPEAKERΩ

–

R L

Speaker (R)

(RP-U100)

Speaker (L)

Red line

Black line

–

Note:

Do not let the bare

speaker wires touch each

other as this could

damage the speaker and/

or the amplifier.

* Non skid

pad

SPECIFICATIONS

Natural Sound 2-way Acoustic

Suspension Speaker System

Printed in Malasia

V425250

Type : 2-way acoustic suspension

magnetic shielding

Driver : Woofer ..... 9 cm (3-1/2") cone

Tweeter .... 2.5 cm (15/16")

balanced dome

Nominal input power : 40 W

Maximum input power : 100 W

Frequency response : 75 Hz – 30 kHz

Sensitivity : 88 dB

Crossover frequency : 5 kHz

Impedance : 6Ω

Dimensions (W × H D) :×

110 (4.3") × 293 (11.5") × 192 (7.6") mm

(stand included)

Weight : 2.0 kg (4.4 lbs) (stand included)

Accessories : Stand × 2

Screws for stand × 4

Non skid pad × 8

Speaker cord × 2

Produkt Specifikationer

Mærke:	Yamaha
Kategori:	Højttalersystem
Model:	NS-U50

Har du brug for hjælp?

Hvis du har brug for hjælp til Yamaha NS-U50 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Højttalersystem Yamaha Manualer

Yamaha NS-35E Manual

7 Juli 2024

Yamaha NS-101 Manual

6 Juli 2024

Yamaha NS-125F Manual

6 Juli 2024

Yamaha NS-U50 Manual

6 Juli 2024

Yamaha NS-4HX Manual

5 Juli 2024

Yamaha NS-U40P Manual

5 Juli 2024

Yamaha Soavo-900C Manual

5 Juli 2024

Yamaha MCX-SP10 Manual

5 Juli 2024

Yamaha NS-515F Manual

4 Juli 2024

Yamaha NS-C444 Manual

4 Juli 2024

Højttalersystem Manualer

Nyeste Højttalersystem Manualer

Auna 10000147 Manual

12 Januar 2025

Jamo A500 Manual

25 August 2024

Paradigm MilleniaOne CT Manual

24 August 2024

Paradigm Millenia LP Manual

24 August 2024

Jamo C109 Manual

23 August 2024

Jamo 8A2 Manual

23 August 2024

Jamo IW 1060 SW Manual

23 August 2024

Jamo IW 625 Manual

22 August 2024

Jamo C10 Manual

21 August 2024

Jamo IC606FG Manual

21 August 2024